Jig & Fixtures
489 topics in this forum
-
So I have been in a update the shop kick where I’m adding better surface to tables, handles on drawers, band saw blade storage, mounting dust collector ect..... I have a pile of tablesaw jigs that I use every great while but still really useful and don’t want to throw out like spline jig, table saw sled, box joint maker raised panel jig, and sacrificial fence as well as the usual table saw assessories. How do you guys store these things in your shop?
-
-
- 20 replies
- 10.5k views
-
-
Thinking about shelling out some cash for the Digi Align jig and would like opinions on this and as to whether its a waste of money etc for example, am I better off making my own, using readily available tools or can this tool be beneficial Im starting to find that (particularly making french cleats) that the timber is burning towards the last part of the cut and also seems to start binding slightly at the last part of the cut making me think things are not aligned as they should be Regards Geoff
-
-
- 9 replies
- 6.8k views
-
-
I had time yesterday afternoon to put together a quick-attach fence for resawing for the new MM20. It's based on the Fine Woodworking article on a universal fence (hanging on the wall to the right of the DP with the drill on it) for the table saw that I use a lot, using toggle clamps for a friction attachment to the existing saw fence. The face is attached using ¼"/20 screws into threaded inserts on the backer. That way I can have a couple of different height resaw fences, a short (lower height) rip fence along the lines of the Laguna, Powermatic and others. I'm really growing attached to the new addition to the family! 9" widths
-
-
- 22 replies
- 9.3k views
-
-
I believe I did a thread on the style of clamp rack I settled on a while back. The "v2" design was primarily Bessey K-Body focused so that gives you a time frame of when I started using this form. My deep-reach and other "odd" clamps often ended up in the raters or who-knows-where. I wanted to improve that and ended up with a variation on the form that I already use which is this: The variation is a narrow overall, three-arm affair. This allows me to hold deep, large head, and other odd clamps while spacing the fixtures on the cleat as best suits the situation. In my defense, the shop is non-operational right now . . . . . . so I…
-
-
- 8 replies
- 5.4k views
-
-
First post, I'm just getting interested in doing some woodworking. I started with a Ryobi BT1000 table saw, it's been a good one so far; yet I have a question when it comes to making a sled. You see, the BT1000 doesn't have the slots, so I'm looking for an option. Bottom line, I'd like to have/use a sled, yet my table saw doesn't have any slots. TIA, Jim
-
- 4 replies
- 8.9k views
-
-
Pretty quick and simple to make. There's quite a few videos out there on making them, this is just my take..
-
-
- 7 replies
- 4.3k views
-
-
I was recently changing blades on my Jet bandsaw and finding it a pain to squirm behind the machine to pull the power plug. Jet power switches have a pin tract for inserting a pad lock shackle. So I came up with this highly engineered solution. The device is manufactured from hard to find (it was at the bottom of the scrap bin) 3/16" oak dowel. This is the cut to some precise length by eye-chrometer. The ends are then conically machined (in a pencil sharpener) and the whole meticulously hand colored (with a Sharpie). As you can see I have limited stock and when they're gone they're gone (I don't have any more dowel). So in the spirit of One Time T…
-
-
- 4 replies
- 4.2k views
-
-
I ordered one of these and it will ship soon. I'm wondering if any of you can lend advice on the bit. They also have the Whiteside Spiral Upcut bit for sale for $50. Any advice on this bit as a good purchase or any others?
-
-
- 3 replies
- 4.2k views
-
-
I saw these on an old episode of Woodsmith Shop and decided to make 4 to use when breaking down my stock with the jig saw. They raise up your stock to allow you to cut over the bench instead of having to have you cut hang off the edge and needing to hold the off cut with one hand to keep it from breaking away and splintering. For storage I put an eye screw in he end of each to hang from hooks over head when I done with them.
-
-
- 7 replies
- 4.7k views
-
-
I am about to begin my next build, and it has 8 drawers. As many of you know, I like making drawers ... complex drawers. And these ones are no exception.[ It got me thinking about the improvements I'd like to make to my Moxon vise. I have plans to make a new Moxon vise, using steel screws and iron wheels ala BenchCrafted, and all the parts are waiting in my workshop. But they will wait until this build is completed. And so I decided to modify the Moxon vise I have been using for the past 8 years. The Moxon vise is not simply about holding a board to saw dovetails. It is also about holding two boards together to transfer the tails to the pin board. I…
-
- 3 replies
- 4.6k views
- 1 follower
-
-
For those of you who use a drum sander you know that sometimes you'll get snipe just like on a planer. The quick trick to eliminating that is just like with a planer - use a sacrificial board in front of and behind the work piece. Now, that's all fine and dandy if you have straight edges on your work piece but if it's oddly shaped or round, then what do you do? Well, what I do is save the cut-offs from the work piece. They're the same thickness and should fit pretty closely to run in front of and behind the target work piece. A few weeks ago I cut a large Lazy Susan and didn't allow enough on my scrap pieces to use them on the drum sander. What I ended up with was a…
-
-
- 9 replies
- 8k views
- 1 follower
-
-
I made this jig up to hold picture frames for finishing. really simple, a couple of slides with finish nails pounded in them, cut off the head end and sharpen them with a dremmel tool, slides are secured with a carriage bolt and wing nut. tighten one end down, squeeze the nails into the frame with hand pressure, squeeze the other end into the frame and tighten the wing nut. holds good for finishing and can be held with one hand to finish all parts then hung up somewhere out of the area to dry. made several of different lengths and can put 4 slides on one to do two frames at once. made them way back when wood frames were popular, they still are around my house anyway, pict…
-
-
- 6 replies
- 4k views
- 1 follower
-
-
I was griping about the foolishness of blister type buttons on a woodturning forum when one of the members wrote back: "Hi,For all who suffer from "Blister Button Switches," there is a reprieve. My X-wife is blind and uses numerous appliances, etc. that have these cursed switches. But, the blind community has long used small, self-adhesive plastic pieces called "Bump Dots" which allows them to both locate and actuate the appropriate switch(es) on said appliances. They are relatively soft. come in various sizes and colors and are available on Amazon, Blindaccessories markets, and probably in many department and craft stores as well." For those interested I was ab…
-
- 2 replies
- 4.5k views
-
-
First, my apologies for those who actually carve and sharpen their tools more normally Even those of us who would never consider ourselves wood carvers may use a gouge now and again. I made this helper for my Worksharp years ago out of a random scrap of wood. It gives me a really nice edge that I hone a bit more before cutting wood like buttah. However, there was always this little divot that existed in the original piece of scrap that left an irregularity. It obviously really bothered me since it took me years to carve out (pun intended) about 20 minutes to make another one. Do yourself a favor, mill your blank square a…
-
-
- 1 reply
- 4.6k views
-
-
For those who don't have commercial versions these are quick to make out of scrap and very reliable. I use these when I am doing one of those rare "production" runs where I need a lot of duplicate parts of a similar dimension but, varying length. These are out of white oak milled to 1" x 1" but, any very hard wood will serve you well. You will want one piece about 3-1/2" long and one about 1-1/4" long for the clamping point. This will make more sense in the following pics. I use 1/4" bolts with a counterbore for the bolt head and a nylon-insert style lock nut on the other end. A 1/4" hole drilled in a piece of scrap clamped to the sander m…
-
-
- 22 replies
- 7.7k views
-
-
This seems as good a place as any to post a question or two about adhesives (if not, feel free to move it). I am getting a lot of end grain tear out on these projects I'm doing. Someone has suggested to me that I glue sacrificial pieces to buttress the vulnerable end grain areas. Seems like a good idea and I have some sacrificial pieces sized up, but I am wondering about what adhesive to use? The ideal material would hold tight until I wanted it to let go and would leave no residue. OK, returning to reality, hide glue (the hot type) might work, but I don't have any nor the apparatus for heating it. Hot melt glue is a thought and I have some, but is…
-
-
- 6 replies
- 3.9k views
-
-
Wow, I've been slacking. No tip since June!?! I imagine we've all been working on something where a bit of "handling damage" occurs in the worst spot. I knocked this little corner off and of course it would be right where two parts butt up to each other in what should be a tight seam. If you are lucky enough to find the wandering bit of material, use a length of clear scotch tape to pick it up. Use a nice long piece, tape doesn't cost much and this gives you adequate "handles" to hang on to. You can see through the tape so that you land the repair right on target. You can see that I actually missed a bit in this demo shot. The tape m…
-
-
- 12 replies
- 4.4k views
-
-
@wdwerker thank you for the excellent tip on DAP Rapid Fuse: it worked great on this "pink wood" project! if it isn't obvious it's a fold out floor flattening dog bed -- yoga mat to follow. I don't know what's in the bottle, but it bonds polystrene foam where CA and epoxy do not. And there are no application temperature range limitations listed on the packaging. It's about 40* F today and it seems to work fine. Otherwise it seems to be like CA only with a little time to reposition.
-
- 4 replies
- 4.5k views
-
-
I simply do not have the floor space to knock down plywood either on the tablesaw or on sawhorses. I needed the ability to cut plywood while standing on edge. I could not justify the $$$ for a retail panel saw, so I came up with a solution that lets me accurately rip and crosscut full sheets while they stand. What started as a harbor freight moving dolly (four wheels for $16!) quickly evolved into a functional cart (or giant skateboard) and then into a simple plywood cart with two sides; one for plywood storage and one for plywood cutting. The sides are sloped 10 degrees to allow plywood to rest and I kept the height pretty low at around 30" to give some space for storage…
-
- 4 replies
- 6.4k views
-
-
I tipped my bucket over and knocked off the top cap. Broke the seal. When I emailed about repair they informed me of which adhesive to use to repair it. They didn't move me to buy a new one. Nice company. I like that.
-
- 6 replies
- 4.7k views
-
-
@Ronn W had suggested moving host post here for searchability, but rather than interrupt the flow of the original thread, I thought perhaps a link would do.
-
- 0 replies
- 2.9k views
-
-
I just spent an afternoon in the shop and it was good and bad. Good to get in the shop (with heat, we were in the high 20’s today), bad in that I was going to make some box joint with a homemade jig. I made the jig a few years ago and marked the shim needed to make snug joints. Well it worked the last time I used it. I set the Freud dado stack with the requires chippers and blades and the recorded shim. The shim marked was a 4mm. The joints were much too loose. Anyhow, long and the short, the last result i came up with after adding and subtracting shims was sockets at .5” and pins at .010” larger. I think I am saying that’s right, the pins were too fat for the sockets. I …
-
-
- 31 replies
- 13.8k views
- 1 follower
-
-
Many thanks to Micks for showing his tablesaw dovetail jig in his medicine chest thread. I have wanted to try dovetails on the tablesaw for some time but, always wanted to do both tails and pins. I had seen various methods for doing one or the other but, Micks showed a combined method. This knocked some rust off my thought process and I drew something up at lunch today. After work I took a shot at version 1. I try to make anything that will do it, pull double duty. My percolation led me to a mod for this small sled that I use primarily for boxes. I make all my sleds with replaceable ZCI's. When I make up blanks I make a bunch. That way blanks are han…
-
-
- 10 replies
- 7.1k views
-
-
For any not following the rebuild of Tally Ho, this router sled inspired jig looks like it might benefit some slab builders.
-
-
- 2 replies
- 3.5k views
-
-
This tip targets those folks who post about poor results when jointing longer stock. We all understand that a jointer uses the freshly cut material as a reference surface against the outfeed table. When jointing particularly irregular stock that is longer than your jointer, the freshly milled reference surface may extend past the outfeed table with still uncut material trailing behind. Many of us deal with this by first knocking down particularly high spots with a hand plane but, some do not. I had occasion today to mill a long piece of stock and thought it was a good time to share a couple of pics. I use roller stands or other forms of support equal to…
-
-
- 12 replies
- 6.4k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·