collinb Posted April 1, 2016 Report Posted April 1, 2016 When it comes to cutting them, it looks like smaller ones are conveniently done with a router bit and larger ones on the table saw with a jig, ala Incra, et al. Is that the general consensus? Quote
Brendon_t Posted April 1, 2016 Report Posted April 1, 2016 Nope. I never cut them on the router. The smallest box joints I use are 1/4" which so happens to be the narrowest cut my dado stack cuts. Quote
Ronn W Posted April 1, 2016 Report Posted April 1, 2016 I general I would say you are right. The one difference that I can see is that the table saw blade does not make a clean of a cut as a router bit unless you have blade that has square teeth or a good quality dado blade. I generally need to do a little clean up with a chisel if I use the table saw. You generally want to take small passes with a router. so, for larger joints you might consider cut the bulk of the material with the table saw or band saw and then shave the last little bit with the router. 1 Quote
Janello Posted April 1, 2016 Report Posted April 1, 2016 Yeah, I'd agree that router bit would only be the better choice if using a jig such as the Leigh or Omnijig. Quote
wdwerker Posted April 1, 2016 Report Posted April 1, 2016 I have cut 1/2" box joints with my Keller dovetail jig. Once you are set up its quite easy and efficient . Quote
mds2 Posted April 1, 2016 Report Posted April 1, 2016 Table saw for me. Never used a router for one ever. 1 Quote
Guest Posted April 1, 2016 Report Posted April 1, 2016 Never cut a box joint. i don't think I ever will. Quote
Chestnut Posted April 1, 2016 Report Posted April 1, 2016 I use the PC 4200 jig it works well for me. I just bought a couple strait bits so i can do mixed size joints as well. Quote
Barron Posted April 1, 2016 Report Posted April 1, 2016 You can go down as far as 1/8" by using a rip blade in the table saw. Looks nice on smaller boxes. Quote
wdwerker Posted April 1, 2016 Report Posted April 1, 2016 I use the tablesaw as well. Found plans for a variable finger joint jig in ShopNotes. I used it to make dentil molding that would end in a full tooth at both ends in a complex crown for a furniture piece. 1 Quote
wtnhighlander Posted April 1, 2016 Report Posted April 1, 2016 I've used the basic fence and pin type jig to cut bix joints on a router table. Worked ok in soft wood, but next time I plan to use the table saw. Quote
jussi Posted April 1, 2016 Report Posted April 1, 2016 Freud box joint blades with ibox for me. Quote
Coop Posted April 1, 2016 Report Posted April 1, 2016 I've been using one of these for a couple of years with a router with great success. Easy to set up and creates good tight joints. http://www.rockler.com/rockler-router-table-box-joint-jig Quote
Dylder Posted April 1, 2016 Report Posted April 1, 2016 Router table. I made a jig similar to the rockler one that works great. Also now I have a Incra LS Positioner on the router table that makes it easy. Quote
Eric. Posted April 1, 2016 Report Posted April 1, 2016 I've done both. They both produce clean results if your setup is right, but the table saw is faster. The router table acts like it's a big imposition to remove that much material. And I hate whining so I usually just say fine and go back to the table saw. Either way is acceptable but TS makes more sense, especially if you have big joints or a lot of joints to make. Quote
Cliff Posted April 2, 2016 Report Posted April 2, 2016 I used the table saw when I did it. I made a dado jig with a 3/8" key. It worked great but fell apart after about 200+ cuts. I have a Incra Jig Ultra now though so I plan to do an upcoming project with that. It's supposed to be pretty easy to use. Quote
Tom King Posted April 2, 2016 Report Posted April 2, 2016 There are not too many things that I've never built, but box joints are on that list. 1 Quote
Popular Post Janello Posted April 2, 2016 Popular Post Report Posted April 2, 2016 You have'nt experienced life until you boxed a joint....I mean, joint fingered a box.....I mean, glued little squares together. 3 Quote
collinb Posted April 3, 2016 Author Report Posted April 3, 2016 In this picture is why no dovetail. Though it is hard to see through the glass reflections, it is a Zone VI 4x5 that I'll be replicating, at least in this respect. No dovetail joints. Sent from my MotoE2(4G-LTE) using Tapatalk 1 Quote
Robby W Posted April 5, 2016 Report Posted April 5, 2016 Table saw. I use a very fancy jig made from a scrap of 1x4 double stick taped to my fence and my dado stack. Cut a piece the size of the finger, use the dado stack to cut a notch in the long edge of the 1x4 and glue it in. Set it up as described in many magazine articles. Because the jig acts like a zero clearance insert, there is little to no readout. Fast and cheap. Quote
Immortan D Posted April 5, 2016 Report Posted April 5, 2016 I use the Porter Cable jig whenever possible, otherwise the Incra Jig/router table. I never used the table saw for box joints, I don't have a dado stack. Quote
Tom Cancelleri Posted April 5, 2016 Report Posted April 5, 2016 I've got a router table jig thing. I've used it a few times. It does the job and it's a nice clean cut. I don't really prefer box joints, but the jig was like 50 bucks with the purchase of another router table jig thing I bought. Table saw will be faster for sure, just make sure you have either a box joint blade, or properly setup dado stack. Quote
Immortan D Posted April 5, 2016 Report Posted April 5, 2016 FTR I tried making box joints with my bandsaw once. Made a jig for that purpose, which included a long threaded rod attached to a sliding stop, a big handle et al. I failed miserably. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.