Isaac Posted December 16, 2016 Report Posted December 16, 2016 So, I'm thinking of selling my miter saw. It seems like I can get most of the same performance from my table saw and it would clear up space for a jointer. What do you guys think, is the miter saw redundant, or will I regret letting it go? Mine is a Dewalt 12", double bevel, but not sliding. It does work well, no complaints about the tool itself. Quote
Popular Post gee-dub Posted December 16, 2016 Popular Post Report Posted December 16, 2016 I too made the mistake of buying a CMS early on because "you have to have one, right?". I found it to be of no use in my furniture making once I had a decent tablesaw but, found the resale to be disappointing. I stow mine in the shed and use it once every few years for trimming out a bathroom or something. Nice little DeWalt, works well for its intended purpose and doesn't take up much room. I would post it and see if you can get enough for it locally to make it worth selling. Shipping pretty much kills any distant customer. Of course, sometimes I sell things cheap or donate them to schools or whatever just to get the space they occupy back for something more useful. 3 Quote
bleedinblue Posted December 16, 2016 Report Posted December 16, 2016 Set it aside and see if you miss it after a few projects. I use mine too often to get rid of it...though mine is a 10 inch non-slider, so it takes up a smaller footprint. 1 Quote
Chet Posted December 16, 2016 Report Posted December 16, 2016 I have the 12 inch Bosch Glide. I am extremely happy, it is really accurate and do a majority of my cross cuts with it unless they are to wide for the saw and then it is the table saw and sled. 1 Quote
Immortan D Posted December 16, 2016 Report Posted December 16, 2016 I also have the 12" Bosch glide and I use it a lot, the main reason being I have to drive 20 minutes to get to my table saw... 1 Quote
CandorLush Posted December 16, 2016 Report Posted December 16, 2016 I do far too much remodeling stuff to get rid of my miter saw but I can certainly see the potential for redundancy once you have a good cabinet saw with crosscut and miter sleds in a purely woodworking shop. Quote
BonPacific Posted December 16, 2016 Report Posted December 16, 2016 Mike and Gee-dub pretty much nailed it. I have one, but it's only used for remodeling and outdoor projects. It's a big old 12" Hitachi, worth keeping around, but not in the shop. Quote
Andy Wright Posted December 16, 2016 Report Posted December 16, 2016 if you need to pick between a miter saw and a jointer I would pick the jointer. I have two miter saws - a SCMS that is attached to a workstation in my shop and a second 12" mitersaw that is "loose" that I use away from my shop. I use both of them regularly, but the one in my shop is mostly for rough cuts so I could live without it Quote
SawDustB Posted December 16, 2016 Report Posted December 16, 2016 I'm in a similar situation, with a 12" non sliding makita. I can't see getting rid of it, since I find it incredibly useful for when the stock is too long to easily crosscut on the table saw. I find I'll get it out a couple of times on a project, with everything else being on a table saw. I don't leave it set up all the time, though - I put it up on the folding stand for the hour I'm using it, then get it out of the way again. As I'm seeing on the Roubo build, too, it has more depth of cut than the table saw. Not usually an issue, but it's certainly nice for cross cutting the legs and other parts. 1 Quote
drzaius Posted December 16, 2016 Report Posted December 16, 2016 I have a good SCMS that I got at least 15 years ago. It still gets used, but less & less. For quick stuff that needs to pretty accurate, that's my go to. For anything than needs to be real accurate, it's the table saw & sled or Incra miter guide. I can't see getting rid of it, but if it died tomorrow, I'd just get a smaller cheap one to replace it. Quote
HuxleyWood Posted December 16, 2016 Report Posted December 16, 2016 My miter saw is usually the first machine to touch wood at the beginning of a project. Stock is cut to rough length before I start the milling. I also use it for a variety of either quick or repetitive cuts. I would not want to lose the capacity it gives me BUT it would be one of the first tools I would get rid of if I needed to pare down for any reason. Quote
ben_r_ Posted December 16, 2016 Report Posted December 16, 2016 Ive thought about trying to go without one, but honestly its just so much easier and quicker to me for crosscuts that fit in its capacity that I just cant imagine the convenience of not having one. Plus I still have a lot of crown molding to do! Quote
Chet Posted December 16, 2016 Report Posted December 16, 2016 Another thing to think about is I am not sure how much you could get for the saw. Would it really be worth your effort to sell it fro a few buck vs. storing for possible use for around the house projects Quote
..Kev Posted December 16, 2016 Report Posted December 16, 2016 Everyone's shop and flow are different. I know I wouldn't consider going without mine and good woodworkers like Mike and Gee-Dub get along just fine without it. My suggestion would be to set it aside for a few months and see how it changes the flow in your shop or see if you even miss it. Quote
wnaziri Posted December 17, 2016 Report Posted December 17, 2016 This a very timely discussion, so thank you all. I also have had the notion that I"need" a miter saw because any good workshop probably has to have one. I have looked at the Festool and Bosch Glide. I ruled out the Festool based on price. I came close to ordering the Bosch unit but could not do it. Reading above opinions convinces me that I can spend my money better on other tools. Quote
wdwerker Posted December 17, 2016 Report Posted December 17, 2016 I use mine at least once or twice a week. I use my sliding tablesaw for large accurate crosscuts ( just like a large sled ). I've got a 12" Dewalt sliding mitersaw and its facing replacement with a Bosch Glide. Quote
Coop Posted December 17, 2016 Report Posted December 17, 2016 Am I the only one that uses a circ saw to break down the lengths of boards. I've seen folks on here use miter saws, with and without a dedicated station, and jig saws (which I've never understood), but never circ saws. I have a ms, not a slider, but rarely ever use it. 1 Quote
wtnhighlander Posted December 17, 2016 Report Posted December 17, 2016 Coop, I use whichever saw is handiest, meaning a hand saw for one or two cuts, a circ saw for a half dozen, and I'll dust off my SCMS for more than that. Never used a jig saw, but only own a crappy one from HF, anyway. I have actually used a reciprocating instrument of destruction (sawzall-type) on occasion. 1 Quote
RichardA Posted December 17, 2016 Report Posted December 17, 2016 I've got a 12" slider, and it's in the way. I never use it, and won't miss it when it goes. I break down rough stock with either a circular saw or a jig saw depending on my wife. She's spending more time in the shop with me, and when she's there she wants to use the jig saw because the circular saw is to heavy for her. Quote
Isaac Posted December 17, 2016 Author Report Posted December 17, 2016 Thanks everyone. I've got it on Craigslist, but so far the response isn't to encouraging, everyone wants a great deal, I'm not desperate to sell, so I'll probably hold onto it. Quote
wdwerker Posted December 17, 2016 Report Posted December 17, 2016 Find the best price on your saw when new. Ask 60% of that to begin with, don't be surprised if the best offers you get are 40% or less . Including accessories or extra blades will make it sell quicker but rarely adds to the price. Craigslist brings out the bargain hunters. 2 Quote
BillyJack Posted December 18, 2016 Report Posted December 18, 2016 I use the miter saw in furniture making. Not everything requires me to set the table saw for cuts. Not everything that comes off the CNC is always that perfect. It can be used here and there and certainly would be missed. Quote
Isaac Posted December 18, 2016 Author Report Posted December 18, 2016 7 hours ago, wdwerker said: Find the best price on your saw when new. Ask 60% of that to begin with, don't be surprised if the best offers you get are 40% or less . Including accessories or extra blades will make it sell quicker but rarely adds to the price. Craigslist brings out the bargain hunters. Yeah that is kind of what I'm seeing. At that point it certainly makes sense to keep it. I guess I'll figure out what I want to do on the jointer end, and then scramble to figure out what to do with the miter saw. Quote
Rex Edgar Posted December 20, 2016 Report Posted December 20, 2016 I find it (meter saw) invaluable in cross cutting long stock. I think one or two others reached the same conclusion. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.