Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Wood Whisperer Guild

Building a Wood Whisperer Guild project? Ask questions about the plans, share your progress, and see how other members approached the same build.

  1. Started by Brendon_t,

    I'm in the appropriation phase of my bench and really like the more traditional look of the handled vise over the wheel. The wooden screw is a bit too traditional so the BC classic seems like a shoe in. Anybody made their bench with this hardware? Does the detent hold well enough to spin it closed when centered?

      • Like
    • 8 replies
    • 3.2k views
  2. Started by Coop,

    Are most guild members planning on building this amazing piece? I'm at awe when I see the the ones at Cracker Barrell, and they are stamped out by the hundreds. It may look and rock like an old HD shopping cart, but I've gotta try it

      • Like
    • 40 replies
    • 10.1k views
  3. Started by Tim Kohl,

    Night stand Started the night stand couple weeks ago, after hitting a few walls Ive made good progress this week. Had to figure out how to make the stopped mortises and lay out a jig for the loose tennons I was going to use. This is a very loose dry fit still need to doctor the loose tennons a little side panel dry fit I milled to 3/4inch used the jig I made earlier to have panel alignment inserts then milled to final thickness. Top unclamped dry fit.

      • Like
    • 8 replies
    • 4k views
  4. Started by Chris H,

    I am going to be traveling for work over the next few months, and much of the time without internet connection. I would like to download several of the project video series to a flash drive to feed the woodworking addiction while I am away from the shop. Is there an easier way to download the entire project, other than opening each video, and then saving the MP4? I did it this way for one project, but it's a slow process. If not, no biggy, but just thought I would check to see if I was just missing something obvious. Thanks!

    • 5 replies
    • 3.3k views
  5. Started by Jim L.,

    Hello All, I'm sorry if this topic has already been beaten to death here, but I'm finishing up my Roubo and trying to decide how to attach the suede for the vises- it seems like there are a lot of conflicting opinions. Marc used 3m spray adhesive, but I read a few forum posts saying that it doesn't hold up well over time. Benchcrafted recommends contact cement, but I read a few other posts that THAT doesn't hold up well. I would appreciate hearing from a few of you guys that built the bench years ago- which adhesive did you use, and has anything come loose?

      • Like
    • 8 replies
    • 7.8k views
  6. Morris Chair Video: Side Rails and Slats (morris-12-side-rails-slats-hd.mp4) Marc uses a 4-wing slot cutter to make a slot in the top and bottom sides (explanation starts at 2:38). I can't find a 4-wing cutter. I'd like to purchase a set (the arbor(s), bearing(s) and cutters) to use for this project. Does anyone know what set Marc is using? Thanks

      • Like
    • 2 replies
    • 3.3k views
  7. Started by tomk,

    I finished my Roubo, and I must say I am very pleased with my decision to use a combination of the soft maple and purpleheart. Two coats of Danish oil have given it a pleasant matte color. Love when the oil hits the purpleheart. My neighbor asked me how long it took to make it (one of the first questions most people ask), and I told him that the project lasted 6 months. That's not the actually man hours of labor, though, and I am trying to get a good estimate. I should have logged in the actual labor time. So, my best estimate is just a bit over 120 hours. Does anyone have a more precise estimate of the amount of hands on time it took to make their bench? just cur…

      • Like
    • 19 replies
    • 5.2k views
  8. I've been toying around with woodworking for a couple years and would really like to get serious with it. I've never had a proper bench and I've done all of my work with my outfeed table. I've seen the Roubo in use and decided a while ago that's the route I wanted to take. Now I've pulled some triggers and am gearing up to get started. I purchased the Benchcrafted bench package yesterday. I went with the traditional "C" style -- I couldn't justify spending an extra $150 just for a polished look. After getting quotes from lumber yards around here (soft maple), I decided to get the bench package from Bell Forest as it's about $200 in savings from the cheapest option her…

      • Like
    • 79 replies
    • 16.2k views
  9. Started by wojo2,

    I am installing the tail vise, but am running into a problem with the nut binding. Initially, the nut moves very freely, but about ¾ of the way towards the end cap, the nut binds. I have tried the following: Run nut without any rails install, nut runs freely. Run nut with only one rail dry fit(not screwed) nut runs freely, with single rail on either side Run nut, with both rails dry fit, and the nut binds. I drilled the hole through the end cap on a drill press with a fostner bit, so I am confident that the hole is true. I have used small levels across the rails, level, Level over the length of the rail Circle level on nut plate, remains level…

    • 5 replies
    • 4.3k views
  10. Started by wojo2,

    I am having an issue with the installation of the tail vise. Like others, the nut starts out moving easily then binds as it gets closer to the end cap. I drilled the hole for the screw on a drillpress, so I am confident that the hole is true. I have used a set of small levels on across the rails, and the rails seem to be level across the gap. I have also used a bullet level on the plate as the nut travels, and it seems to remain steady. I have tried the following: Nut with NO rails, moves the length of the screw no problem. Ran nut on one rail at a time again no problem. Did both sides, one rail at a time. Two rails loose fitting, prob…

    • 0 replies
    • 3.1k views
  11. Started by pridmore,

    All- I just purchased the DVDs of the wall-hanging cabinet and a few other guild projects from TWW store at 50% off. I'm going to do this build first. I'll probably build a "prototype" or two to use as shop cabinetry, but want to go ahead and buy some good wood to acclimate to my shop. Does anybody have a rough idea of the number of BF? Thanks for the info in advance. Andy

    • 2 replies
    • 3.6k views
  12. Started by morganew,

    I have the benchcrafted classic, just finished installing it. In an attempt to see how tight I could make the vice, I sheared the pin. I'll try and get a hold of benchcrafted tomorrow, but if not does anyone know the pin size off hand? (yes, I can grab my calipers, blah blah blah). Thanks in advance.

    • 0 replies
    • 3.3k views
  13. I saw a thread on another forum where a user suggested a larger slab up front. I think the idea of roughly two 12" pieces that can go through a planer is cool, but if you are willing to pass on that feature, which I think I am, would it be better to have a less symmetrical set up - say a 16" slab and an 8" one? It seems like it might give more flexibility when using the planing stop in the split, but I'm sure those of you who have actually built one would know better than I would. (And if we did need to use a planer, I'm sure Shannon wouldn't mind if we all showed up to plane that 16" slab on his giant planer since he loves the sound of power tools at work, right?)

    • 4 replies
    • 3.6k views
  14. I'm upgrading my vise to a BC leg vise and am going to (for now) move my quick release vise to an end vise (something I've never had). Some day I'd love to build the split top and upgrade to a BC end vise, too. If you've done this do you miss your quick release vise at all? (I'm trying to figure out if it is worth trying to fit it on the bench somewhere or not - my hope is that the answer is no). All that said, I recognize that my bench is made of inexpensive material and was made when I was a relative beginner, and is not thing of beauty, but it is certainly fine, relatively functional, and not a major limiting factor in my woodworking even in its current state …

  15. Started by AdamAronson,

    All, Been loving my Roubo! Thanks again to Marc and and the fellow Guild members for the help. I'm looking for suggestions on how to get to actually make use of my hold fasts. Simply put ... they don't hold. I can't get them to grip in the holes I drilled in my 4" thick Ash top. I drilled the holes by hand with a power drill and a 3/4" brad point bit. As a result some of my holes are not 100% square to the top and some are slightly irregular. Could this be the problem? If so, would the best remedy be to plug the holes with 3/4" Ash dowels and glue and then re-drill with a guide? I've tried sanding the shanks of the hold fasts with 80 grit paper... not help…

    • 13 replies
    • 5.9k views
  16. Started by SeventyFix,

    1. Dogs I assume that no finish goes on the dogs or in the dog holes, correct? 2. Suede (a) I used contact cement to glue the suede to the dogs and it was a total failure. The glue did not hold at all. I peeled it off, roughed up the dog face with sand paper and used CA glue (cyanoacrylate/super glue). Instant bond and worked perfectly. The suede is permanently attached to the dogs. As Marc suggests, I am going to use spray adhesive on the leg vise chop and bench front (though I haven't done so yet). ( Have any of you put suede on the leading edge of the guide block and the opposite face, where the guide block closes as you turn the wagon vise?…

      • Like
    • 3 replies
    • 3.6k views
  17. Started by morganew,

    I've got an odd situation with my newly installed crisscross. It closes very smoothly and cleanly, but it's stiff when opening. The threaded rod is not touching wood anywhere and I've got about 1/4 of toe-in. Spec from benchcrafted is between 1/8 and 3/8, so I'm well within the range. ANyone else had this happen?

    • 1 reply
    • 3.3k views
  18. Started by jhoward967,

    Just a quick question: do you recommend filling the pores on the bottom veneered panel of the humidor? And if so, would you recommend filling and sanding before assembly of the outer box (to facilitate easier sanding)? Thanks much! AHo

    • 25 replies
    • 7.1k views
  19. Started by shanesmith80,

    My toy box has been finished for a while now, but has taken me a while to work out how to shrink the photo size to allow to post. That and I have been lazy. So here it is.. Made from New Guinea Rosewood, with Jarrah for the plugs. 5 coats of shellac. Bottom and draw lined with putting green grass carpet. Overall I'm fairly happy with how it turned out for my first project of this size.

  20. Started by popper,

    I'm a guild member and a member of the Hand Tool School. I would like to thank Marc and Shannon for their videos and email support though the build. I built my bench with mostly hand tools, except for the planing marathon for the top and the 3/4" wide 1 1/2" deep by 47" long mortise for the deadman, which was the last thing and I was about to be a dead man myself. I used walnut for the legs, chop and end cap, got it from a local supplier. Eric at Bellforest worked with me to get the rest of the wood I needed for the build, which was all maple. I was really happy to find 16/4 walnut for the legs. This was only the second real woodworking project I have do…

      • Like
    • 23 replies
    • 4.4k views
  21. Started by morganew,

    Making a new chop for a crisscross, and I was able to get some extra thick and wide Cherry. it's currently s4s and still 2 3/4 thick. I could plane it down, or bandsaw and then plane, but it's only an extra 1/4. Is there anything I am NOT thinking of that would make the extra 1/4 a problem? Thanks in advance; Morgan

    • 4 replies
    • 3.3k views
  22. Started by HunterL,

    Hey guys. Pulled this piece out of the press this morning and there is some shiny spots. It's walnut burl. I've tried my card scraper but it doesn't seem to be very effective. I also CAREFULLY went over it with 180 grit with my ETS 125. Thoughts? Sent from my iPhone using Tapatalk

    • 7 replies
    • 3.5k views
  23. Started by gwlorenz,

    I just veneered my first piece of bubinga veneer to the spanish cedar and noticed a fairly significant amount of glue bleeding through the pores of the veneer. My veneer came extremely flat and there was no need to use the softening agent to flatten it out. Not sure if this was the reason for the bleed through or if I used too much glue (there was not much that sqeezed out from the sides, though). Has anyone else had this problem? And, now that it has happened, what do I need to do to get rid of the glue before continuing? I'm especially concerned about having glue on the surface or even in the pores for the pore filling and finishing processes.

    • 3 replies
    • 4.7k views
  24. Started by Slmize,

    I have just got back in town from work and see the guild is on to bigger and better things. I have decided to build the blanket chest and have a question on the bottom. Decided to do the alternate method but am not clear on the method of attaching the plywood to the deck. I'm pretty new at woodworking, is it just glued or is there another means to attach it. Would appreciate any advise I can get,I realize this is kinda behind for everyone. Thank you and merry Christmas

    • 4 replies
    • 3.3k views
  25. Started by t3e871,

    I had a little trouble with the square plugs breaking when inserting and I believe they took me the longest to make. These chairs started at 8/4 cypress with purple heart plugs. I finished with a seal coat of shellac and covered with 2 coats of (50%) thinned epifanes clear. Thanks for the build Marc - it was very rewarding! See more of the progress and my cramped garage shop here: https://picasaweb.go...feat=directlink

    • 6 replies
    • 5.4k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.