The Wood Whisperer Guild
Building a Wood Whisperer Guild project? Ask questions about the plans, share your progress, and see how other members approached the same build.
500 topics in this forum
-
I am going to build a variation of the COD but am going to start with some nightstands before I tackle a dresser. I want to use the Domino for the M & T joinery but not sure it will work with the grooves in the legs for the panels. Do I need to make a stopped groove instead of having it run the length of the leg? I know that Marc used haunched tenons for part of the joinery. I think I can do something similair using different sized domino stock, has any one ever tried this? Thanks in advance! James
-
- 3 replies
- 4.1k views
-
-
Hey everyone, I'm starting the Humidor, but I've just recently gotten rid of my table saw. I do have a TS75 track saw, and I'm hoping I can accomplish the tasks in this project with the track saw and router. Did any of you do this without a table saw? If not, do your prolific imaginations have any good ideas for ways to accomplish the various tasks involved in the build? I know it will be a lot slower of a process as setting up cuts will take longer and such, but my situation is reality and I don't want that to stop me. Thanks!
-
-
- 12 replies
- 3.7k views
-
-
Made a trip out to Amish country and picked up my cherry from Yoder Lumber on Friday morning. There is a Morris chair in there somewhere :-) Sent from my VS980 4G using Tapatalk
-
-
- 10 replies
- 4.8k views
-
-
Hi folks, I'm part way through my build and unfortunately I don't have stock wide enough for the legs. The legs I've made up are around 4" wide. I've only now just noticed an issue ... When I line the base up on the top with the shoulder vise, I notice that my leg vise leg doesn't fall right in the middle of the dog hole strip gap. Wondering what options I might have (aside from building the entire base again!)? Also, is the narrower legs going to be an issue for the leg vise? Cheers, Af.
-
- 2 replies
- 3.6k views
-
-
I built my Roubo in March of 2012 and I really enjoy it except for the pin of the leg vise. I dislike the pin so much that I almost never use the leg vise. Well today I installed a chain kit form Ancora Yacht Service and I just have to say this thing is fantastic!! My leg vise glides even smoother than before and will clamp anything within it's range of travel just by spinning the hand wheel. It only took me a couple of hours to install and I only had to drill a few holes in my existing chop and bench leg. I'm sure my bench will see even more use now.
-
- 3 replies
- 4.1k views
-
-
Hi, The front and rear slabs of my bench are laminated and have been run thru the planer. I am ready to trim the ends of the slabs square. I thought I was going to use my 10 inch sliding miter saw to saw half way thru then flip the slab to saw the rest of the way. But much to my dismay only about 3.75 inch of wood will fit under sliding head of my Makita saw. So my remaining options include an old circular saw, router, hand saw or buy something like a fancy track saw. Any suggestions? I have not had great luck accuracy wise with the circular saw. How did you trim your slabs to length? Thanks for the advice. Paul
-
- 10 replies
- 4.5k views
-
-
Hi all, I am getting prepared to start the workbench but am having trouble sourcing the Benchcrafted Vises in Australia. Any ideas? EDIT: Corrected to Benchcrafted.
-
-
- 3 replies
- 5k views
-
-
Given the upgrade to the Benchcrafted Roubo hardware, has anyone found a use for the old screw and hand wheel after upgrading?
-
-
- 5 replies
- 3.5k views
-
-
I meant to start this thread earlier but never got around to it. I'm building out of cherry because I like how it ages naturally and I already have a few other G&G pieces that I've done with it. I'm leaving my stock as thick as I can so most of it comes in around 7/8'ish The base and breadboards are about 1 1/4". I built the finger joints in my glue up. The other changes I'm making are I'm going with more of a finger joint base like Darrell's, and I'll go ahead and do the ebony splines that bridge the top and the breadboards (mostly because I already have all the jigs built to batch them out). So this is how far I've gotten so far.
-
-
- 21 replies
- 6.3k views
-
-
I'm way behind on the wall cabinet build, so I'm just now looking at getting the material for the back of the cabinet. The cabinet is made out of blue stained pine (bunch of images here: http://www.google.com/search?q=blue+stained+pine&hl=en&prmd=ivns&tbm=isch&tbo=u&source=univ&sa=X&ei=PsDCTZryJ6eC0QGF0sTuAw&ved=0CEIQsAQ&biw=1207&bih=679 ) There's no plywood I can get for the back, so I'll need to do something else. I can just go with any random plywood and it would probably be fine, but I was wondering if anyone had any good ideas. I suppose I could plain some wood down down 1/4" and slide it in the back, but I don't thin…
-
- 2 replies
- 4.7k views
-
-
Made some shop cabinets that are based on this guild build. Since this is my first woodworking project my goal was #1 to learn some woodworking skills and a distant 2nd to get some cabinets. Virtually everything was a first time to me, from milling to finishing. Even made some jigs along the way including a cross cut sled (my favorite tool). All possible using Marc's guild videos plus the huge amount of advice I got on this forum, thanks everyone! Used cheap construction lumber (once again, this was a practice project), the wood is presumed to be spruce (called white wood at the store), the ply for the doors is birch. Finished with 4 coats of matte water base poly …
-
- 17 replies
- 5.4k views
-
-
Has anyone with the classic leg vice had an issue where the screw doesn't fit into the hub? The flange fits fine, but the hub won't go on at all. In their video it looks like it should just slide right on without any resistance, so I don't know. I don't really want to whack it with a hammer because I'm afraid I won't be able to rotate it to line up the holes for the pin. I emailed Benchcrafted so hopefully they get back to me, but I was just curious if anyone had a similar issue?
-
-
- 7 replies
- 3.9k views
-
-
Since there are quite a few people making the Adirondack Chair, I thought it would be a good opportunity to road test some outdoor finishes. I'm sure most of us will wind up using different products and of course we all live in different climates. So it would be super duper cool if each of us starts a thread here in the Adirondack Chair forum where we discuss the finish we used and post a picture or two. Then as the seasons/years go by, we can each come back and update our post to reflect the current condition of the finish. What do ya say?
-
- 3 replies
- 4.7k views
-
-
Hello all, I am very interested in learning how everyone's chairs have held up to the finish chosen. I am looking to start this build over the next couple of months and since it has been a few years now since the initial build, I'd like to learn some feedback on the finish you used. Please post some pics and a few words about what finish you used, if you had to re-apply and how you went about the re-appication (maybe the wood type you used as well). Also, did you cover up? Hope to hear from you all. I'm a new guild member and looking to get my first guild build under way. Loved all the pics. Really great job by all, Fred
-
- 13 replies
- 5k views
-
-
Greetings everyone! I just got my chairs back from the upholsterer and I think they look fantastic. I'm still waiting on the ottomans, and I'll send the pics when I get them in about a week. In one of the pictures you can see the Greene and Greene blanket chest from last year's guild build. The pieces really compliment each other, I think. A bit about my project: - Species: African Mahogany - Finish: General Finishes Dye Stain (3:2 mixture of Medium Brown and Cinnamon), with Qualaq lacquer finish. - Webbing: Jute webbing with trimmed dust cover - Seat: Natural leather hide with batting-covered foam cushion core - Back: Natural leather hide with polyester fil…
-
- 11 replies
- 4.8k views
-
-
As i look over the plans i see the legs are mortised in to the top one inch on each leg. Since the top is held down to the base with the spax fasteners, what is the purpose for the mortises? I do not see any draw pegs. Just curious. Thanks
-
-
- 4 replies
- 3.8k views
-
-
I was in a hurry to finish up and well.... I cut the legs 1" shorter than the plans called for. I had plenty of scrap and so I cut an extra block and using epoxy extended the leg. I have plenty of extra to recut to the right size now, but the glue line is pretty obvious. I tried again and still got a pretty significant glue line. I was thinking about cutting down just below the glue line essentially making a giant tenon and then cleaning it up w/ a shoulder plane and then applying a thick veneer to at least two of the sides that are going to be easily visible. Is this a viable option or does anyone have any better options?
-
-
- 5 replies
- 3.5k views
-
-
I'm sure I'm not the only one to gaze lovingly at the benchcrafted vise hardware package, but be just a bit unsure about whether or not to spend the money. I'm working on the top of my guild Roubo build, and agonizing over that particular purchase decision. I'm doing this very much on a budget, for instance, using big-box SYP lumber instead of the maple I'd like to have. DIY is a sickness that runs deep in my veins, and so the more I looked at the benchcrafted vise hardware, the more I started to think that I could build my own for a fraction of the price. I've mostly reverse engineered it from the photos on their website and the dimensions in the sketchup dr…
-
-
- 27 replies
- 14.8k views
-
-
Coming up for air after lots of milling and mortising and it seems like a good time to share my progress. You will also see some adirondack parts in the background. I got started on that as a warm up project in April and I am trying to keep it moving along with the Morris. I'm fairly new to woodworking. Long time DIY type, but had some projects during the holiday season that required some woodworking. I started out bringing an old table saw back to life, but since then I have gone fully down the rabbit hole. I got my lumber home and as I was laying things out I realized that I had nearly enough 8/4 lumber to make 2 sets of legs and arms. I decided to double down and m…
-
- 19 replies
- 5.1k views
-
-
My calendar on the guild page is highlighted for today with the finishing video scheduled. Up top, in the highlighted banner with member information it says next video is upholstery on july 18. Did I miss something?
-
-
- 10 replies
- 3.6k views
-
-
Anyone else having issues downloading the videos? I save them to my laptop so I can watch them at work without getting in trouble for using their bandwidth, but they are only downloading about 88kb/sec and my download speed is 18-22MB/sec. So the video downloads are take over an hour per. Is it me?
-
- 7 replies
- 3.7k views
-
-
I believe I have finally convinced my wife that we need a chest of drawers...so I am starting to get things in order to build along (albeit a bit late starting). The catch here is that she really wants a slightly lower cabinet that is double wide. This will be a big hall table/chest for things like hats and gloves and so on. I'm starting to draw up what I plan to build using the chest of drawers as the base, reusing all of the construction techniques/etc. This brings me to my first issue. Given that this will be double the width, I'm debating how to handle the case structure in the center (between the drawers). 1 - one option is to just build a center frame …
-
- 6 replies
- 8.8k views
-
-
A member posted that he's having difficulty getting over some hurdles with this build. Likely there are others. As many are already well advanced on their project, they could likely help someone stuck a little ways back. I'm guessing most of the needed help is in the form of jointing/planing stock be it by electricity, ATP, or frenzied beavers. So, if you want to put yourself out there to possibly help out, reply to this thread. Someone stuck can find someone in this thread and PM them to see if they can help out with whatever hurdle is in the way. To the requestors, be sure to put some detail in any query. And also: it is to get over a hurdle, not get side-b…
-
-
- 36 replies
- 12.1k views
-
-
Hi Marc, What would you say is the minimum resaw capacity required for this build? Looks like the final arm dimension is 5 1/2" Can I get away with 6" capacity? Thanks, Fred
-
-
- 20 replies
- 5.1k views
-
-
I need to clean up the tenon cheeks on the front legs a bit. what is the best approach. I was going to use my low angle rabbit plane but am worrying about blow out in the ends of the tenon which would be really bad given its a through tenon. typically i would chamfer the ends to lessen the blow out but won't that impact the look of the tenon when it shows through? Do I just plane from each end towards the middle?
-
- 3 replies
- 3.6k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·