The Shop
1,954 topics in this forum
-
Due to a lack of space and a need for mobile power tools I got myself a combo tool. It is the Smithy Super Shop. http://www.smithy.com/index_inside.php?id=238&type=supershop The first time I used it I realized that I needed an outfeed table for the table saw function. My problem is that the height of the blade is set by raising or lowering the table and not the blade, so the outfeed table would have to move up and down. If you have any ideas I would love to hear them.
-
- 4 replies
- 8.4k views
-
-
Hey guys, believe it or not, my Colorado garage shop is waaaay bigger than my regular home. Today I am building two lumber racks, one of them inspired on Marc's video and another one inspired by me ... lol I will post pics manana.
-
-
- 4 replies
- 4.1k views
-
-
I spoke with an A/C contractor recently about putting in a minisplit system in my 3 car garage. Needless to say the cost had me overheating!!(pun intended). His recomendation was to look into a whole house fan for the garage. The side effect would be lower energy usage throughout the entire home. I was confused how a whole home fan in a garage would help the electric bill and he stated that the pulling of the cooler air from the garage(cooler then the attic air) would push out the hot stale attic air and thus lower the energy load on the A/C system. Has anyone looked into these and would anyone have experience with them in actual use?
-
-
- 14 replies
- 32.6k views
-
-
Hi guys. In short I live in Australia and have been a carpenter since 16 years old. Did my apprenticeship in a joinery shop, went on to work as a subcontractor then started a company 20 years ago building cottages in much the same way construction in North America is done. 2 x 4 frames, cladding, cut rafters to the roof and often exposed for show. I closed the company a couple of weeks back due to the massive down turn in the industry as well as personal circumstances and now am looking at setting up a joinery shop behind my garage to supplement my income. I am still a contractor but have decided no more house construction, maybe some fitout work for other contractors …
-
-
- 26 replies
- 10.3k views
-
-
Hi Guys. A couple of years back I bought a heap of GMC (Global machinery company) tools because I was told the company had gone out of business. Dirt cheap and was too busy to do anything other than open the boxes, have a quick look and then put them aside. Now that I am looking into getting into joinery rather than general cottage construction, I have unearthed a lot of these tools. Watching Marc's videos on the festool routers, I am noticing an awful lot of similarities with the 2200 festool to my 1500 watt GMC and my 1020 shares similar designs with the smaller festool routers. Of course I am hoping that these cheap tools will last a few years given weekend warrior w…
-
- 0 replies
- 3.5k views
-
-
Down here in Houston it's freakin HOT!!. Even though i've got a garage thats attached, insulated on all but one side, & has a orientation that keeps the sun at bay it's still hot. I was thinking of picking up one of those portable AC units from the lowes or home depot. I'll be cooling roughly 600 sq feet. Any personal experience with them. Are they worth the investment. Yada yada you know the routine!! Thanks guys.
-
- 20 replies
- 16k views
-
-
I was curious if anyone has ever broken a cleat with excessive weight, or more to the point, if there is a theoretical limit for the system?
-
-
- 23 replies
- 42.8k views
-
-
The internet is helping to level the playing field regarding price of tools. You guys in North America may not be aware of how cheap things are there in comparison to the rest of the planet. The driving force is your numbers. America has 528 million compared to Australia's 20 million. This is some serious buying power! To give you an idea, here are a couple of price comparisons on items that do not require electricity so that we don't get into the debate regarding different voltages and electric motors. Also, the Australian dollar is buying $1.07 US at present, has been for the past three months and will probably continue to do so for another year or so. Festool Routi…
-
- 7 replies
- 4.4k views
-
-
What would you do if you had; 300 acres of timber shop that could be renevated to anything you want (40'50' your own sawmill I'm curious to know what other would do.
-
- 9 replies
- 4.7k views
-
-
I do not sell these things, lol I can see that people may think I do, but I am scouring the web looking for bargains and solutions for my new shop. My crime is that I am one of those people that enjoys sharing info with others. So here we go. I noticed in one of Marc's videos that he had purchased some wall units and placed them at the rear of his shop, the first time round. He later commented when moving back into his garage/workshop that he should have invested in something stronger and more secure. These cabinets measure 710 x 710 x 300 deep, that would be 28" x 28" x 12" deep, lockable with a key and they are French cleat mounted to the wall. I think these sizes ar…
-
- 2 replies
- 4.4k views
-
-
so, i've had enough of the garage. too hot, too cold, concrete floor, car parked outside, etc.. you guys know the drill. i'm going to leave my machines in the garage for the rough work and frame out a room in my basement for the hand tools. i'd like to have a comfortable floor to work on but i know nothing about hardwood flooring or any of my other options for a slab basement. i seem to remember someone using a nice paneling material over osb and insulation but can't seem to find it. any ideas or pointers on where to look? jason
-
- 8 replies
- 4.6k views
-
-
To let every one know I am the new owner to a Rigid table saw R4512. A Incra 1000se miter gage and a Ridgid 13 planer. The three new tools have improved my woodworking skills 1000 times over. Its truly amazing how the right tool improves your skills. Woodworking is once again so much fun. The table saw and miter gage make cuts dead on. I stand by all Ridgid tools. Some people don't like them. For what reason I have no idea. this weekend I hope to put all of these tools through there paces. By making matching end tables.Somethingg me and my wifeHavee beenwaitingg to do for several months. Ill post what they look like.
-
- 1 reply
- 3.9k views
-
-
i would like to hear about the smallest shop or work space that you guys have come across and there space saving Solutions
-
- 17 replies
- 6.3k views
-
-
-
I am building my first router table and need some help in selecting the right router plate insert. What dose every one recommend? It's a cabinet stile that is 36" tall and the table will be 24" by 30". I see some with a micro adjust built in them. Is this worth spending the extra money?
-
- 5 replies
- 4.6k views
-
-
I just got a new stereo so the old one found a new home in the garage shop. It's pretty nice equipment and I'd like to keep it that way. I'm trying to figure out how to keep the bulk of the dust off of it without suffocating and overheating it...it pushes a fair amount of juice to a couple pretty heavy speakers. Thinking about building some kind of housing that would utilize furnace filters on two sides, and putting a fan or two in there. You guys have any brilliant ideas for keeping the electronics in your shop clean and cool?
-
- 9 replies
- 4.2k views
-
-
Has anyone used a Lee Valley Right-Angle Assembly Clamp or another brand of the same type of clamp? If you are not familuare with these clamps they have no "force" to them. They just act like an extra hand. At least thats what the add says. I just need to know if the 10 bucks is worth the it. Of course I would use full force clamps (corner or pipe)when doing a glue up. Thanks; Scotty
-
- 1 reply
- 4.6k views
-
-
Hello , Just moved into a new home with a 3 car garage. I'm "allowed" to use to bays of it , as long as my fiance gets to park her car in one. Here are some pics of the progression so far. More to come.
-
- 6 replies
- 4k views
-
-
ok i need to update the dust collection system in schools wood shop. the previous shop teacher put in the clear plastic piping and hooked up 3 shop vacs to the ends which covers a length of about 100 feet. it works well enough to make my bosses happy but not great. We have delta dust collector(model 50-840) in the shop that was buried because my curent teacher is eather lazy or enipt and does not put any work into the shop he just collects a pay check. (let not go into my frustraiting work conditions right now maybe letter after i work out on a punching bag). the system is set up like this V:115/230 A:9/4.5 Hp:1 Rpm 3450 Ph:1.3 wire HZ:60 i know a little ab…
-
- 10 replies
- 5.5k views
-
-
Say all the tools, cabinets, etc in your shop were gone in a fire, tornado, theft, whatever, and you had a nice fat insurance check to replace everything. What would you do differently? I'd get a parallelogram jointer instead of my 6" Rigid, even if I had to save up for it. And I'd seriously look at getting a shaper instead of my home made router table, Jessem lift, and dedicated PC 690 router. I'd get shorter rails on my table saw, the 52" rails don't really fit in my shop. I'd look long and hard at a CMS with better dust collection. My DeWalt CMS is fine, except it sprays dust all over the room and there's no easy way to capture it. The main thing is that I'…
-
- 7 replies
- 4k views
-
-
After I finish my next project, I'm going to change a couple of things in my shop. As I'm writing out my wish list, I couldn't help but wonder what some of you are planning. I'm going to: 1. Take out a closet so I have more wall space for big power tools 2. Remove my never used radial arm saw and move my miter saw down so I can add a longer fence with stop block. 3. Build a cabinet base for my contractor table saw and add dust collection to the router that's mounted in the wing. That's it for the major stuff. What are YOU going to change?
-
- 21 replies
- 5.7k views
-
-
Some of you may already know - I took a trip to Springfield, Missouri last weekend and visited Grizzly Industrial. I bought a new 3hp Grizzly cyclone at a super price. I took another trip yesterday - about a 7 hour round trip drive - to buy my duct pipe for the collector. I'd already sent a rough drawing of my machine locations to Grizzly showing ceiling height and distances from my machines. I plan on setting the cyclone in the middle of the shop to save money on pipe and to improve the cfm to each machine. We're talking no more than 10 feet from the collector to the furthest machine, as the crow flys. I'm only going to connect the cyclone to the jointer, planer, table s…
-
- 21 replies
- 7.8k views
-
-
Marc's recent video on building a lumber rack gave me the kick in the pants I needed to fix something that I've been needing to do for quite a while now -- revamp my lumber storage. I was originally going to use horizontal racks like the ones in this thread. But then I found pictures and descriptions of a vertical lumber rack, which I proceeded to completely copy. This was good, because now I see that my original plan to mount horizontal racks would have been less than ideal for me in many ways. Here's what I started with -- a big pile of wood on 2x4's that I bought at an auction a couple of years ago. As you can see, I couldn't get to the wood on the bottom or toward…
-
-
- 9 replies
- 113k views
-
-
Hey folks, I've got what is possibly the smallest shop I've ever heard of - the skinny half of a one car garage (about 6'x18 for the shop). Who here is dealing with similar circumstances, and what solutions have you come up with to get everything to fit? Right now I just bring everything out to the yard under a canopy as needed, but winter comes quick around here, so that won't be a good long term solution. Here's a list of what needs to fit: Work bench 9" lathe (table mounted) 8" grinder 12" bandsaw Benchtop tablesaw Lumber rack Benchtop planer Benchtop jointer Miter saw Clamps, clamps, clamps, and also some more clamps for when I need a few extra Ha…
-
- 12 replies
- 5.5k views
-
-
Hi all, I've been very slowly working on this because spring has had me doing a lot of honey-dos and regular spring wake up chores. I just finished today and posted on my blog. Let me know what you think.
-
- 6 replies
- 4.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·