Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Shop

  1. Started by Vic,

    These are a few pics of my studio/shop. The explanations are attached to the flickr shots. This shop took me five years to build and is extremely energy efficient for heating and cooling. The walls have a nominal 3 inches of polyurethane spray foam and the attic has R50 cellulose. It has very little impact on our energy bills, except for the big power tools. I still need to build my assembly/outfeed/bending table and a Roubo bench. Other than that, it's pure heaven to me. If you would like a live tour or have any questions, I'm very often streaming from http://thewoodwhisperer.com/live/# Here's the link to my Flickr page. http://www.flickr.com/photos/30350434@N07…

    • 37 replies
    • 12.4k views
  2. Started by TheSwede,

    Gents, New to the forum. Have been fideling around with woodworking for some time now and hope to be living off it one day. First step to do that is to set up a propper shop. I have one which I equipped about 8 years ago but now found it not sufficent for me needs. I thougt I post about its progress here and hope to hear some comments. The total shop is about 6 x 10 meters (sorry for the metric, dont understand your inches ) First thing was to improve insulation, we have about 5 month of winter here in Sweden Second thing was to even out the floor, it is just raw concrete that was never even when first poored out. I'm gooing to use a selfe evening mass for this…

    • 12 replies
    • 8.7k views
  3. Started by nikbrown,

    Ok right now I have a sub panel in my shop. The entire shop is on 2 15amp 110 lines... needless to say I keep popping breakers. I have to turn out the lights to run the dust collector and the 110v contractor table saw at the same time I'm not afraid to to do my own 110v stuff but I stay away from wiring my own 220. (Plus they will have to pull wires from the house to the shop, probably). The current shop subpannel is full and has 60amp service (there is also a well pump runing off this panel). I'm betting I'll need more amps than that but I'm not sure. So I need to get an electrician out here to upgrade the shop. I plan on switching to 220v tools over the next few …

    • 10 replies
    • 5.4k views
  4. Gang, My cabinet manufacture and furniture building business has grown to the point where I am moving into a larger space. Through word-of-mouth the side-business has grown. Now I have to move a lot of heavy equipment; cabinet style table saw, shaper, drum sander, and jointer; just to name a few. It seems the best approach is to disassemble the machines then crate or otherwise protect the parts. Are there other approaches? Thanks, Bobbie

      • Like
    • 11 replies
    • 4.2k views
  5. Started by Roger T,

    Morning all, I have come to the conclusion that having all my tools on wheels and having to move them in and out each time I use them is a real pain in the rear. So, I am wanting to redesign my shop to have as many of my tools stationary as possible. I work in kind of cramped quarters, and also have 2 steel support posts that inhibit my open floor space to work around. Also have a furnace and water softener that share my space. Is there a program, and or guidelines that would help me in getting a working layout for my shop? My most used tools are my bench of course, 2436 lathe, MM20 bandsaw, jointer and planer. Are there templates to use for tool placements? G…

    • 13 replies
    • 16.4k views
  6. Started by Dave H,

    i've been bulding a new workbench and want to put a leg vice on it. i've been looking at the shop fox bench screw h5577 in the 2011 grizzly catalog on page 261, it looks like it should do the job my question has anyone ever used this product and if so where you happy with the purchase? also in picture on p 261 it shows the screw, and nut with a flange for bolting to the leg of my bench but it doesn't show any such bracket or flange that would attatch to the jaw of the vice. am i missing something or is there another part thats not showing. i'd really like this to work beacause it's in the budget $31. maybe someone else knows of another bench screw that won't break the ban…

    • 2 replies
    • 5k views
  7. Started by newbiewoodworker,

    Frankly, I am always tripping over stuff… Also, it is a pain work for long periods in. But, maybe you can provide me with some ideas on how to make the shop a little more cozzy… Don’t get me wrong.. I love my little shop… its where I go to stress relieve… but when you trip and go falling into the workbench.. it is never fun…. Here are the pics, for you to provide suggestions from.

    • 8 replies
    • 3.9k views
  8. Started by d8nk,

    My air compressor seized 2 nights ago and the motor kept running. The motors built in protection didn't trip, the circuit it was on had GFCI protection and didn't trip, and last, the circuit breaker at the panel did not trip. So I entered the shop to a noise you never want to hear coming from your equipment and the room was filled from floor to ceiling with thick blackish blue smoke. The belt melted, started on fire and melted the plastic belt guard. After clearing the smoke out of the shop, I am left with a horrible smelling shop. What was once a great smell of wood is now a sickening smell of burnt petroleum based products. I have a professional restoration specialis…

    • 7 replies
    • 6.4k views
  9. Started by IveGotWood,

    I am currently helping my brother remodel his garage into a modest 550 sqft shop. Our current design has our dust collection unit housed in a small shed that is connected to the exterior of the garage with the dust running through the shop wall. We thought this would help reduce the noise and the amount of fine dust that would be recirculated into our shop. We thought this was pretty slick until we saw a clip TWW did for Powermatic's site where he said that this type of setup could pose potential problems if there was a hot water heater in the shop. The reasoning behind this was the dust collector would be pulling fresh air out and this air would not be replaced. Thi…

      • Like
    • 10 replies
    • 7.9k views
  10. Started by toneslinger,

    Ok, pretty much a newb in the the forum so if I post in wrong area, my apologies. I recently asked Marc, Matt, and Shannon about recommendations for next steps in upgrading my garage/shop. The resounding recommendation was dust collection. As I was hoping. Here is the challenge. I have a budget of $350 and of course, like everyone else, limited shop space. The question is, can I get "adequate" dust collection or at least a really good start on a dust collection system in that budget? Currently, my only solution is the poor rigid 6HP Shop Vac. Here are the specs on my two car garage shop. Large open area in the middle with most tools on the walls. Ro…

    • 30 replies
    • 15.2k views
  11. Started by gary-g-k,

    hi i am currently haveing a power issue in my shop. as of rite now i only have 110 outlets. the main problem is that the braker box is full. we have no more room to add a 220 outlet. and iam trying to get some nicer tools but all the tools that would be upgrades need 220 outlets. is there any way that i can get a 220 out in my shop for theses tools? any sujestions would be nice thanks gary.

    • 12 replies
    • 5.1k views
  12. Started by Sully,

    I was given an old 60"x60" woodworking table about 5 years ago. It is the type that many of us used when we were in Jr. High/High School wood shop class. It's a beautiful maple table top about 4 inches thick and has 4 vises. My dilemma: I checked out the flatness of the top and found it had a pronounced crown, about 1/4". I proceeded to use a couple of methods to flatten it; Belt Sander and hand planning. So far it's a very slow go. I would continue planing, but had shoulder surgery, which makes me sore for days. Belt sanding "seems" to work, but it slow. I've reduced it a bit, but wondering if there is a better way. Does anyone have suggestions? The top weig…

    • 5 replies
    • 3.7k views
  13. Started by ChetlovesMer,

    My previous shop had a false floor with laminate flooring. It was nice because I ran dust collection and electrical under the floor. My new shop is a standard 2 car garage. Now I have a concrete floor. My lower back aches after too many hours out there. So, I recently bought a ton of those "puzzle-piece" rubber flooring mats. Now my floor is softer much easier on my back. I think it also helps keep it a little warmer in there, but that may be psychosomatic. Just curious, what do you all have for flooring in your shop?

    • 20 replies
    • 7.6k views
  14. Started by ssrt3,

    Picked up my new table saw yesterday from sears, cant wait to set it up today. ill post pics as i get it unpacked.

    • 11 replies
    • 5.1k views
  15. Started by Dean Hummel,

    Is white oak a suitable wood for a Roubo style workbench top? Oak is an pen grain wood. A lot of purists recommend a close grain wood such as maple for a bench top. In my opinion, people made workbenches out of local woods on hand and I have a good line on some wide (like 10 inch wide) straight grain 8/4 white oak. Second question is there a minimum thickness for a Roubo style bench top? I think 6 inches is way overkill but 2 inches may not be enough, even if it is oak. Finally is it acceptable to use face grain for the bench top or should I cut the oak into strips and laminate it up on the edge grain? Thanks for the collective wisdome! Deane

  16. Started by Mikpohl,

    Background...assuming I have a garage shop about 18ft by 22ft, I'd like a bit of clarification on Dust collection needs. I'd like to hook up Router table, Planer, Jointer & Table saw and keep the Dust collection unit in one place. Not exactly sure of duct lengths needed. With this in mind I'd like to overbuy a bit in HP/air suction. 3 questions... 1) Is there a noticable difference between 1 & 2 HP? Does 2hp equate to twice as much suction as 1hp? 2) I see Delta 1hp model is highly recommended on Amazon, like 183 reviews, yet Jet & others have very few (1 or 2) reviews. Is Jet 2hp a solid choice? I see a PennState Model for 3hp in same price range ( m…

    • 2 replies
    • 4.1k views
  17. Started by gardnesd,

    Hey all, I'm currently working out of my garage. I have been doing serious woodworking for about 6 months. The garage is essential covered by 1 15amp circuit. It's definately not enough. I cannot ALWAYS run my track saw and festool dust vac at the same time. God forbid I have a space heater as well. Also, when we move into this house we "moved" the laundry room. Now the dryer and washer are on the same circuit as well. It's good times. I have plans to build a shop in the backyard in the next 2 years and most of my troubles will be gone. However, it appears that all of the breaker spaces on my panel are taken. Is there a way to add a second panel? I know very …

    • 10 replies
    • 4.4k views
  18. Started by ChetlovesMer,

    Seeing Dave's shop has made me absolutely itchy to go out and make sawdust. However, I am still in the process of setting up my current shop. I've been here since August and I'm still setting things up. To my defense, I did change jobs in October, and I have a 6 month old in the house, so its not like I've had tons of time. (But I admit I miss this old shop.) But, because Dave shared his beautiful shop. I decided to share what was my previous shop. This shop was great to me and I built some projects in there that I was really proud of. However, I didn't get my sawstop until after the shop was built, so you won't see it in the video. Also, you might notice a lack of q…

    • 10 replies
    • 4.8k views
  19. Started by nayliner,

    I have the Powermatic PM2800. I have not been able to find a good clamping solution using the slots in the table. All the drill press clamps I have found are bolt on through the table. Just curious if anyone has a solution for the Powermatic drill press or if I should just invest in some nice deep throat clamps. Thanks for your input.

    • 1 reply
    • 4.7k views
  20. Started by jgfore,

    I have just bought a (not new, but new to me) Powermatic Dust Collector for my shop. I need to run the duct work for the DC around my shop. I am planning on using PVC pipe instead of metal due to cost. Does anyone have any do's and don'ts for running the pipes. I have not done this before, so any suggestions are welcome. Thanks Jeff F

  21. Started by JeffWaggoner,

    Has anyone ever used this or know of someone that has? I like that you can change the bit with just a hex wrench but I am concerned about vibration. http://www.amazon.com/gp/product/B000EXQ2FA/ref=s9_simh_gw_p60_d0_i1?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=center-2&pf_rd_r=1TT63V444WBPR0HR8S1Y&pf_rd_t=101&pf_rd_p=470938631&pf_rd_i=507846

    • 3 replies
    • 4.7k views
  22. Started by 00101,

    Okay, I am in the process of cleaning my shop and have turned to the good ol' stockpile of wood, which was in disarray from having pulled boards out of the middle and just leaving it to lean and collapse as necessary, and started to pull it out to reorganize it. Well, the dilemma is do I organize based on what best fits a solid continuous pile, species of wood, general size, color, thickness, others? I have one bay of shelves around 12' long and 2' wide so I can't have like 30 different piles. So basically, how do all of you store your wood?

    • 3 replies
    • 3.9k views
  23. Started by ssrt3,

    ok im sure youv'e guys heard this a hundred times no im setting up a permanent dust system, i have all the trunks run and the drop offs now what i cant find is flex hose at a good price here. cheapest i found was 4.50 ft,does any one have a place to get hose at a better price than that? Thanks the main is 6" and drops are 4"

  24. Started by jgfore,

    I have the wall mounted storage area for my lumber, and I am assuming that most people have some sort-of the same type of storage. This would include a nice lumber rack to a pile of wood on the floor. But what I am wanting to know is, does anyone store BULK lumber. Let me explain. My father is about to cut down a LARGE oak tree and a pretty good size cedar tree. I have already spoke to a portable sawmill about cutting it up into lumber for me. My problem is that I do not have a place for........2000 board feet of lumber. I am going to trade a good portion of the lumber off to the sawmill for cutting it up, but this will still leave me with enough lumber to fill my entire…

    • 11 replies
    • 6.1k views
  25. Started by A_Vitale,

    So As of now I am working out of the garage. I have a three car garage and am using the small one car as my shop. I am here in Mi so I have to deal with warm summers and cold/snowy winters. I have the luxury of moving from the garage to my homes basement, here are some of the pros and cons. But I really need input, cause I am torn! Garage Pros -Easy to bring in materials and machinery -Natural light during the warm months -noise in at a minimal from the inside of the house -Dust is kept out of the house -Currently have storage built Cons -Temps swing greatly from summer to winter months. -I would have a heate…

    • 20 replies
    • 14.4k views

Who's Online (See full list)

  • There are no registered users currently online

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,010 Total Members
  • 3,644 Most Online
  • Lolli4 Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.