The Shop
1,954 topics in this forum
-
I am doing some upgrade work on my 1970s Craftsman table saw. The gentlemen that I purchased it from had added a dust collector kit that attaches to the motor and has hoses going to the blade guard as well as into the base of the saw. Runs great, cast iron top with cast iron extensions on both sides, little rust that I cleaned up, and at $100, a complete steal. I am waiting for a Delta T2 replacement fence to arrive by UPS - the factory fence is absolute junk. I have read the work it takes to get this fence installed, but have read great reviews. Now to my issue, I am removing the saw from the factory steel 4-legged base. One of the legs is bent, and since my shop i…
-
- 3 replies
- 5.2k views
-
-
I am considering building the Wall Mounted Lumber Rack System which I found plans for from WoodSmith® Plans. Check out the plans and tell me if you think the rack system would be a good and strong system. I do not want to waist my time and wast a good piece of plywood making something that is going to be junk. I have included the link to the plans below. http://www.woodsmithshop.com/download/211/lumberrack.pdf Thanks Jeff
-
- 18 replies
- 18.8k views
-
-
Stampy this is for you.... My workshop site dates back to 1364, but the building I occupy now is from circa 1600. So fairly old you could say, it was a dairy up to about 1600 then became the estate carpenters shop from about 1750 and has been such from that time. My great great great grandfather purchased the farm buildings in about 1870ish and has been ours since. My grandfather was a cabinet maker so I became one too, he didn't use any of the buildings for his shop, but worked for other people. I however worked with my grandfather in his shed, and was hooked that way. I decided to start my own woodworking business 2 yrs ago, and decided to use the old carpenters shop…
-
- 16 replies
- 6.9k views
-
-
For some time now I have been wishing for a larger table saw top. Until I recently built my out-feed table I made due; however, the new out-feed table spurred me on to work on my table saw too. Over the weekend I used angle iron leftover in my shop from another paying project and one 27x20 piece of 10GA metal to make a side extension table for my saw. Now my saw table and out-feed table are matched in width. I already used the extension this weekend to cut some shelving to length. I did not have to push down to hold the shelving from tipping off the saw and could better focus on cutting the piece instead! Hallelujah! I am including one photo as a "before" showing t…
-
- 5 replies
- 6.7k views
-
-
Hi. I am a noob. I love Mr Whisperers stuff. I watch his podcasts religiously and repeatedly. As an Aerospace Engineer, I thought it'd be fun to over think things. So, I'm seeking comments on this: I chose the wood craft trash can design, as it was the simplest by far. http://www.woodcraft.com/Articles/Articles.aspx?ArticleId=408 (used with out permission) So far, I've spent 29.99 on a 32 Gallon Trash Can. I plan to mount it above the blower motor on a shelf. That way, I'm using as little footprint as possible in my little two car garage (that still holds two cars). For my cubic feet per minute (CF/M) variable, I used 500CF/M based on Bill Pentz data…
-
- 16 replies
- 15k views
-
-
I am looking for a good method to store all my scrap wood. Much as wood cost I hate to throw stuff away. You never know when you will need it. I would like to have you share with me what type of process do you use that works. The best way I can think is new long boards be stored on rack, smaller pieces be put on shelves, but if someone would have a unique way to do so, I would love to hear. Thanks Tom
-
- 17 replies
- 25.7k views
-
-
I have just recently installed the duct work for my dust collector, was wondering what everyone else's thoughts were on grounding the PVC piping. Is it needed? how to do it? and issues that you all may have had? Thanks Guy
-
- 27 replies
- 35.8k views
-
-
here are some pics of my shop i built 3yrs ago. it's just a tease it's such a mess right now i'll show some inside pics at a latter date. scroll down a bit i was able to add pictures instead of files
-
- 5 replies
- 5.4k views
-
-
Okay, here's the deal. My wife and I are currently in the process of buying a new house. I currently don't have a shop and any woodwork I've done was done in my father-in-law's shop. The new house has an absolutely amazing detached garage. Neither of us care about keeping any vehicles in the garage, so it is going to become a workshop (at least, some of it is). My wife wants (at least some of) it to become a workout room. Based on the size of the garage, I think that we'll be able to do both and still be plenty happy. It's not set in stone by any means, but I imagine that the RV portion of the garage will become the shop (with the possible exception or the lo…
-
-
- 13 replies
- 4.6k views
-
-
So seeing someone else post their nice assembly table motivated me enough to post a couple pictures of mine. Mine is inspired heavily by Marc's assembly table design, but I've made the following changes/features: Much smallerAdded wheels, remove the toe kickMade it the same height as my table saw so it's also an outfeed tableUsed only drawers, I have enough shelf space already (for the time being at least) I still need to put some sort of finish on it, but it's functional as the somewhat beat up top indicates. This was my first wood working project of any size, so I made quite a few mistakes: The center of the case is taller than the sides because the center divider di…
-
- 4 replies
- 5.8k views
-
-
Hey Friends, Just a picture of the project that got me to this guild. I had been checking out the FWW site and saw Marc's video on building this assembly table. I thought it looked awesome and decided to give it a go. I'm usually not a great video fan, but Marc's whimsical but knowledgeable style held me like a Jet full body clamp. After I finished the project I did a search to see if he had any other little things drifting around and was floored when I found this site. Looking forward to our current build and I hope you enjoy photos of my finished project. Thanks Marc for everything you do. Dave
-
- 19 replies
- 7.5k views
-
-
I am moving into a new home in the next few week and will have a stand alone shop. Right now my shop is in my basement. unfortunatly my new shop does not have any heat. Living in New england it gets pretty cold in the winter. I do most of my woodworking in the fall and winter months but i do sometimes build in the summer. My question is will the cold have any affect on my tools? right now my basement stays about 50 degrees or so all winter long so it's not too bad. I plan on keeping all of my finishes in the house. also right now I run a dehumidifier year round so I dont worry to much about keeping wood down there. How bad will the humidity of the summer affect any of the…
-
- 7 replies
- 4.3k views
-
-
I'm building a workbench and I am planning on using four layers of 3/4 MDF or four layers of 3/4 plywood as my top, but I am wondering as to how MDF/plywood will hold up as a work surface, or should I top the MDF with a layer of 1/4 in. Hardboard to protect it! I'm gonna wrap the edges in Oak or Maple. I would love to build a traditional bench but cost is the major factor here. I'm thinking that if I go with the Hardboard top at least I can remove it and replace it should it gets too beat up. One of my concerns with using MDF, the lag screws for my vise will not last. I plan on using the bench for both hand and power tools, and there will be dog holes. What do you think…
-
- 8 replies
- 24.7k views
-
-
I looked at a lot of plans and took pieces I liked from various ones. It's made of jointed and planed Douglas Fir 2x4's and 2x6's and finished with danish oil. Took about 2 weeks to build in my off hours. Maybe 12 - 14 hours not counting glue and finish drying time. All the bolts are recessed so they can't get caught on anything and all the edges are eased so nothing's sharp on the legs. The top will be secured to brackets with hex bolts. The brackets then slide into saddle joints on the legs. The feet are connected with wedged and glued M&T joints (the only glue used on the whole thing other then laminating the milled dimensional wood together) and have height b…
-
- 1 reply
- 3.6k views
-
-
Just finishing the base and top and am really, really pleased with the results. Never had a worktop that flat and straight before. It will be a pleasure o work and build on. Thanks to Marc for the video and plans to follow. I applied 3 coats of General Arm-r-seal to the top and it got really smooth and looks like a furniture top. One slight issue Im having is that i used semi gloss instead of satin like Marc used on the demo video, and its a little too shiny and slippery. Any solutions for this besides putting on a couple coats of satin Arm-r-seal? I have a non slip pad that I use sometimes for this purpose, but even that seems to slide a bit.
-
- 1 reply
- 4.5k views
-
-
A week or so ago I finally finished a small shop project. Once I started it didn't take that long. I built two of these boxes for my work bench. They hang on the horizontal rail on either side of the bench. All you have to do is lift them up to reposition them. Both can be on one side or one on each side. The bottom is a piece of stainless steel expanded mesh. This allows saw dust and wood chips to drop through. It also allows for screw drivers or other tools to stick through. I recently started putting the long driver for my Kreg screw down through there too when attached to my impact driver. It keeps me from knocking the driver off the bench and it keeps it fr…
-
- 3 replies
- 4.3k views
-
-
Hello all, I'm hoping to get some help and opinions from the folks out there. I have recently moved to a new house and am trying to sort out a new shop. Given some various factors (small lot size, township codes, available funds, etc) it looks like the biggest size I could have for a standalone shop would be 12'x20'. I am considering a manufactured building such as this: My old shop was 20x35 and plenty big so I don't need something huge. I've been playing around with the Grizzly shop configuration tool and can't seem to find a good layout. I'd like to hear everyone's opinion on whether a 12x20 would do the trick. I am currently thinking that it's a bit t…
-
-
- 33 replies
- 74k views
-
-
I finally got tired of the wimpy little tool rests that came with my grinder, and made this thing: It's much better. Check my blog for more information and a set of detailed drawings for building your own. -- Russ
-
- 3 replies
- 7.6k views
-
-
Hey all; Just joined the forum, so I figured I'd show you my hiding spot. The building is 10'x16' and originally was an implement shed built in 1910ish for the orchard that is now my neighbourhood. (Lots of fruit trees around) I poured concrete over the old rough floor and put in more wall studs as the old ones were on 21....22...26...inch centers. There are only 2 original studs as a result. Natural light and a view of the back yard was key in this project. My wife has an amazing garden. So I replaced the two 10"x10" windows with the ones you see in the pictures. I found the windows locally. The came out of an old estate home in the area. I installed a 40 amp servi…
-
- 11 replies
- 6.1k views
-
-
Howdy all, I'm in the middle of getting quotes to add more power to my shop, and I'm looking for any advice on what to look out for, tips, or things to consider. I'm currently in a 20'x20' two car garage (one side of which is currently consumed by the biggest waste of space, my wife's car ), and sadly I only have 3 110V outlets in the whole space! I'm planning on filling up the shop with larger power tools in the next year or so, and with that comes the need for 220V. I know a lot of you have some great experience with building shops, or have had work like this done before, or just know what you like and dislike about your power setup. So I'm just looking for any…
-
-
- 13 replies
- 9.3k views
-
-
Currently I'm using a laminated beech (I think) worktop that's about 1 3/4" thick and is actually pretty nice if plain. No dog holes, no clamps. Just a flat top. It has steel legs which aren't the most stable in the world so I am building a new base for the top now out of laminated douglas fir. The next step will be to determine what I want to do with the top. I definitely need to think about clamping capability and features like bench dog holes, bench dog storage, tool holders, etc. Anyone have pics of your workbenches or ideas that you have found useful when customizing an existing workbench? My shop is broken in two with my power tool shop being in part of …
-
- 10 replies
- 13.1k views
-
-
Ok everyone, just made the jump from the standard shop Vac, to that of the Jet dc-1100a dust collector. I'm planning on keeping out side of the garage ( covered in a shed next to the garage) and cutting a hole into the shop. The collector says it can have a 6" or two 4" hoses. Is it best to use a 6" then step down or just run two 4 inch hoses? I don't have a large shop at all so is 67" worth it? any comments would help. Don
-
- 5 replies
- 5k views
-
-
-
anyone in the colder climates have a heated cabinet to put there finishing supplies in when the shop isnt heated?
-
- 8 replies
- 4.9k views
-
-
With the build of my new basement shop I am starting to think of some ideas as far as storage goes. The space will fill up fast so I am gonna be limited on doing a whole lot of base cabinets. Show show me how you guys are storing your bits, hand tools, glues, clamps, jigs, etc. I kinda like the idea of open shelves/cubbies...but I really am needing some inspiration.... Thanks in advance!
-
- 8 replies
- 6.1k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·