The Shop
1,954 topics in this forum
-
So my shop don't currently have power and I'm wanting to run new lines out to it. I don't know anything about electrical but based on what I figured out at home depot, I need UF-B 12 AMP 2 Conductor with ground. Does anyone know if that sounds right? or am I on the right track? Thanks for any help
-
- 11 replies
- 4.5k views
-
-
Merry Christmas everybody. I'm in the process of building a 24x24 shop, it's pretty much 75% completed. Some paint, electrical, and shop furniture still remains to be completed. And of course setting up my tools. I received an iHome radio for Xmas this year. I was thinking about building a "dust resistant" cabinet for the radio and DVD/TV combo that I currently have. In my previous 11x15 basement shop (with average Dust Collection) it seems that dust is attracted to electronics and I was constantly wiping them down. I was wondering how do you guys protect your electrical devises from saw dust. On a side note the iHome radio does not have an aux speaker jack/ou…
-
- 6 replies
- 9.3k views
-
-
Hello, I was lucky enough to get a new Grizzly 6" jointer (Model: H0452P) for Christmas, but as I was happily setting up the machine, I found what appears to be a crack on the bottom side of the outfeed table. At first I thought it was the paint, but when I looked further, I noticed that the crack reached around the bottom and up the other side of the table. The crack does not appear to have any easily noticeable effect on the table, but I'm afraid that the crack will only get worse with time until it becomes a structural issue that will have an adverse effect on the outfeed table's flatness. Am I correct? Should I have the jointer replaced, or am I over reactin…
-
- 3 replies
- 3.7k views
-
-
Here is a brief photo tour of my shop. It stands alone from the house. I still have some work that needs to be done to it like wiring and bringing out 240V. Here it is as of today, project mess and all. It's not the prettiest, but it's MINE! Let's see your workspace!
-
- 50 replies
- 21.6k views
-
-
I'm currently starting to set up some basics in my shed/shop and right now it doesn't have power due to the lines being pulled down during an ice storm a couple years ago, so I have a 100ft extension cord ran out there and have 3 shop lights and a small 2 gallon air compressor hooked up. (Also have a table saw but haven't used it yet) but the lights flicker each time the compressor kicks on and I'm a little worried I may have too much going off one outlet and haven't even began to use my saw yet. Is the light flicker common? should I do something different? any tips/advice? Thanks Jason
-
- 9 replies
- 4.5k views
-
-
How to finish around the window? The first pic shows a piece of 2x4. So there's 1.5 in of depth to get to the level of the framing. The drywall will add another 5/8". So, Do I glue up to get 1.5+.625 (2-1/8th) thick piece the width of the gap there, about 2.5 in, drywall meets it, and molding covers the joint? This project is slowing to a crawl, lots of not whole sheets of drywall.
-
- 2 replies
- 10k views
-
-
For the past two evenings I have been dismantling the far right section of my previously “finished” chop saw station. This was a small platform section, immediately to the right of the chop saw and … in between the chopsaw and the radial arm saw table. Remember … these surfaces are flush and the fence on the RAS is aligned with the fence on the chopsaw. Recently, I stumbled on a Craigslist gem, a little-used Delta power mortising machine. I brought it home and put it on the platform on the chopsaw station where I had always hoped that “a mortising machine would go.” My big concern was … would it fit? It came mounted on a very heavy steel base which was almost as …
-
- 1 reply
- 4.3k views
-
-
Here's a two part shop tour video I just posted at penultimatewoodshop.com Next time I'll try to plan it through first.
-
- 17 replies
- 6.1k views
-
-
I am planning on putting in a real workbench top. My local supplier has large cants of air dried white oak. He can saw it up into any dimensions I want. What would y'all recommend? 1. A large 1 piece slab top 2. Cut it down into 12/4 boards and then glue them back together 3. White oak would suck as a workbench wood Thanks Renee
-
- 5 replies
- 4.2k views
-
-
What's up wood nerds? Once we moved into our new home I got half of the basement to turn into man town. So 15x25' of workshop awesomeness is slowly but surely coming together. Built a temporary workbench and the Woodsmith Shop Sliding Cabinet so far. With each project i'm learning more and slowly building up my shop tool collection, but air cleaner and dust collection are next on the list. Any recommendations? TWW has been a great source of info and ideas and I'm thinking the guild may be a next step as well. Shop tour to be posted soon and good to hear from everyone. RB
-
-
- 22 replies
- 11.6k views
-
-
I am finishing the basement mostly to create a nice sized workshop a keep the dust from getting all over. The ceiling plan is to use CeilingMax which are plastic strips that screw to ceiling and hold up drop ceiling tiles. I am first putting up 1x2s (furring strips?) which will hold up the plastic channels and also leave that room to run the wiring. Note - This was approved by the inspector. Permit pulled and electrical inspection passed rough in. I have go ahead to drywall, and call him back once outlets are in. Also, this room will be a dance rrom for my 12yr old. That lower pipe is now 7'2" off ground, will lose no more than 2 more inches between final floor and ceil…
-
- 5 replies
- 9.7k views
-
-
The price of LED tube lights are coming down finally and I will be investing in a couple for lighting over my workbench....replacing standard CFL tube lights.... My question is what color lighting to go with for best lighting that would be comparable to natural lighting outside?
-
- 2 replies
- 4.3k views
-
-
I'm looking for anyone who has experience moving the PM2700 into a basement workshop. Weight is about 600 pounds. I have an exterior basement entrance with six stairs that is easily accessed from the garage. Because the shaper is top heavy one idea is to place it on a heavy duty appliance dolly with the cast iron top against the dolly frame. The shaper would be on its side and I'd fasten it to the appliance dolly with straps. I'd appreciate your thoughts. Thanks, Pete ******SUCCESS****** Thanks for all your suggestions they sure helped! With the help of a professional safe mover and my son-in-law we moved her into the basement today. Took advantage of …
-
- 8 replies
- 5k views
-
-
After wrestling with an "almost too wide for the miter gauge" board one too many times, I finally broke down and built a cross-cut sled. This isn't one of those deluxe sleds that you are going to use for all your cross-cuts, but it's a way to cut those wider boards that aren't practical to cross-cut with your miter gauge. If you don't have one of these things, drop what you're doing, get out to the shop, and go build one already! It takes about an hour, can be made from scraps you already have laying around, and afterwards you'll wonder how you ever got along without one. Mine is made from a 14" x 16" wide piece of 3/4" MDF. Plywood would work too, but I'm finding …
-
- 5 replies
- 4.8k views
-
-
Hello all, I can sure say things have finally fallen in place and because of deciding to live elsewhere and selling our retirement property, I'm currently building my own shop. This will be 28' x 34' and will be a dedicated wood shop. I've been doing like so many others on this site and other sites, search the internet, read articles in books/magazines until it's all a jumble in your head and you really don't care anymore, you just want it finished. Anyway, I will be doing all the interior work but there are some things that I haven't quite made up my mind on yet and others I have so I'm wondering what you all think? The ceiling height is 11' so I've had (6) 2'H x …
-
- 9 replies
- 4.1k views
-
-
Hello everyone. I recently joined the Guild and am looking forward to being active in the community. I am putting together my shop slowly in an unfinished room in our basement. I have easy access to a subpanel for power. I need a lot of light. The space is approximately 10'x20'. I would like to put up flourescent shop lights. Any suggestions on output, bulb type, number of units?
-
- 15 replies
- 4.9k views
-
-
-
Do any of you have suggestions on outlet placement? In a home they are generally a foot or so off the floor. I'm thinking in the shop you probably want them just above bench height, and maybe some that are closer to the floor for whatever purpose. Any insight or wisdom on this topic? Thanks
-
- 23 replies
- 15k views
-
-
Saw stop saved my finger on 11/10/10, this is the message or testimony that I sent to SawStop when I reported the accident. I would like to say that I am very glad that the extra money spent went to good use in buying a SawStop Contractors Table saw. I had a kickback that hit my left hand, thus causing me to flinch and hit the blade. I did not have the blade guard installed, just the riving knife as I was cutting a narrow piece from the board. After the activation, or loud "BANG" I looked at the saw and wondered where the blade went, not realizing what had just happened I looked at my left hand and the index finger was red with blood. I looked at the finger and s…
-
- 22 replies
- 16.7k views
-
-
I have looked before and always it ended up on the backburner but thanks to Onboards great topic it is back in my mind. My shop is a seperate structure about 100ft away from the house so if God forbid there was a fire I would have no way of knowing until it was too late, does anybody know where I can get an alarm that would alert me in the house? Nate
-
- 4 replies
- 4.4k views
-
-
When my wife and I bought our house we knew that the basement takes on water from time to time. About once a month we seem to get a lot of rain and I get three large but shallow puddles. I am working on the drainage issues but I doubt we will ever be totally dry. We actually looked at it as a positive. Expect water from time to time. Don't expect to ever be tempted to make it living space and don't feel guilty making it a dedicated shop. I spent the last few days cleaning and rearranging in anticipation of building a new workbench. Came down today and a few of my jigs were sitting in a puddle. It got men thinking about my upcoming bench. I try and keep…
-
- 16 replies
- 5.7k views
-
-
I just recently watched the assembly table base get constructed by marc and had a thought about the air hose system. When I build mine, if the measurements allow I would like to mount a retractable hose pully inside with a roller guide to protect the hose as it exits the base. I've been looking all over the internet for the guides but can't seem to find them. Does anyone know the proper name for them? Its 4 roller assemblies arranged in a square that sorround the hose.
-
- 3 replies
- 4.8k views
-
-
Long ago I was told that “it’s easier to obtain than to maintain”. I’ve seen confirmation of that adage many times over the years, and I’m sure you have made similar observations. I imagine that the collective of woodworkers is all over the board when it comes to having done an inventory of the contents of their shop. Just read a good article on doing such an inventory primarily for insurance policy purposes. It includes a downloadable pdf Workshop Inventory form, and also has a link to the 5s method that can be applied to the shop environment.
-
- 5 replies
- 4.6k views
-
-
I am using the tools more and would like to make the band saw "stand alone", also I can no longer lift it with back issues. The Shopsmith stand at $335 would be a budget strain. I have some salvaged motors the bigger one is 3450 rpm rated at 1/2 hp. Anyone ever do this? Any suggestions? Thanks Wiskey
-
- 4 replies
- 5.4k views
-
-
OK, next question for my backyard shop. Should I frame things myself or buy a prefabricated shed/garage/storage building? Prefab kit prices seem quite high, especially when you add in what the manufacturers deem to be "options": doors, shingles, a floor. Metal (i.e. Versatube) seems even pricier. As carpentry goes, I'm thinking it doesn't get much more basic than a 12'x24' box with a gable roof. What would you do? What do you have now? Kit or from scratch?
-
- 9 replies
- 3.9k views
-
Who's Online (See full list)
- There are no registered users currently online
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·