Finishing
2,922 topics in this forum
-
I am making a simple earring holder similar to the one in the attached photo. I am going to use some left over purpleheart and was wondering what would be a good finishing option. The other earring holders have been made from cherry with a clear oil finish and then waxed. I know that purpleheart likes to change colour over time and I would like to keep the purple colour as long as possible. Thanks.
-
- 10 replies
- 5.3k views
-
-
Ok, quick question. Is there a "correct" combo of marker/sharpie and finish? I have tried sharpie under shellac (spray and wipe). It dissolves the sharpie. I would imagine poly would do the same? The project I am working on is a gift for my nephew's baptism. I made a simple cross with oak and walnut. We a writing a little message on the back. (along with To, From, Date type of stuff) (Just for the curious mind - cross is about 8" tall and 4" wide. oak is 3/8" thick and walnut is 3/16".) All I am trying to do is protect the message a little bit. The obvious easy way to avoid the issue is to just not have the issue. Do not put the finish over the marker. …
-
- 5 replies
- 21.3k views
-
-
Hi All, Any suggestion on a small polisher/buffer? I have many boxes I have made and will use shellac and then wax so I would like to use a small polisher/buffer to save some time and my arm! I have been looking at the porter cable 7424 but it looks a little big for what I need. Thanks NYHump
-
- 17 replies
- 10.8k views
-
-
Does anyone have respirator recommendations ? Especially for paint, varnish, lacquer or other noxious sprays. Will also use for general dust inhalation. I have the AOS and the head strap is difficult to use with glasses (bifocal) on.
-
- 10 replies
- 5.3k views
-
-
Just getting into the world of shellac and picked up Vijay's video. Great process walk through on French Polishing! I'll definitely have to give it a try sometime. But as to my question, what hues of shellac do you use with certain woods? I've heard that Platina or Super blonde are great for sealing the wood and then I've heard that using garnet or orange will help with popping the grain. Then I've heard that orange or garnet are great on mahogany or cherry. Any thoughts on colour wood combos? It's soo confusing!
-
- 9 replies
- 7k views
-
-
The wife has me building some cabinets for her and although I've painted them white and they look nice she would like the glass smooth finish that the bathroom cabinets have. The cabinets from what I can tell have no brushstrokes but are obvioulsy painted. Any professional guys know any tricks that could be passed on? I had planned on using my earlex 5000 HVLP gun to spray the latex paint and possibly spray a waterbased topcoat to finish them out. would that get me the glass smooth finish or no? Thanks Adam L
-
- 3 replies
- 7.9k views
-
-
I have a log cabin that is about 100 years old that I am renovating. The interior logs are pretty beat up. I have blasted them down with ice pellets and have smoothed them down with an Osborn buffer. Any suggestions on what sort of finish I should use? We are trying to be as environmentally sensitive as we can. There are lots of photographs online if you want to get a better view. Thanks for any suggestions. I've only recently found this site and it looks very nice!
-
- 1 reply
- 3.4k views
-
-
So when using paste wax (S.C. Johnson's in this case), it's recommended to use a power buffer to generate enough heat to get a good finish. My question is, what do you do about the corners where the buffer won't fit? I try to prefinish where I can when everything is flat, but sometimes that's not possible, and of course there's the issue of re-applying later. Do you just do what you can with a rag and just not worry about it, or are there some tricks to getting the little details?
-
- 1 reply
- 3k views
-
-
Can someone tell me what size compressor (33 or 60 gal.) I need for some semi-pro work. I don't need a constant feed but at least enough to finish the drawers then the case etc.. Thanks
-
- 5 replies
- 4k views
-
-
Hello Everyone, I've been using the internet ever since Al Gore invented it but this is the first time I've ever posted on this type of forum, so I hope this goes right. I am in the process of dismantling a 112 year old barn that I plan to transform into the furniture in a new house. I am wondering if any of you have any words of wisdom and/or caution on what to use as a finish/finishing techniques, so that I can keep the "patina" (sp?). Also, any thoughts on the best way to clean and prepare the wood for use. Thanks, Todd
-
- 10 replies
- 12.2k views
-
-
Soliciting the collective wisdom of the forum as time ticks towards the final stages of the build challenge over at Sawdust Chronicles. I'm building a Scrabble board and am looking ahead to potential finishing pitfalls. Conceptually, it's very much like a face grain chess board (not an end grain cutting board) just with more pieces and a more complicated pattern. This is only one half (OK, actually eight fifteenths) and it'll be flattened, sliced open, bookmatched and veneered onto a sheet of ply. Bits of panga panga, purpleheart, koa and padauk are scattered around a field of alternating maple and ash. A ways back, I discovered the hard way that the pigment in p…
-
- 1 reply
- 3.3k views
-
-
Asked about this on another thread but don't want to totally hijack so here goes. Saw Norm using a poly/stain mix and got me thinking about a problem I'm having. Used Marc's shellac seal coat technique on pine, applied a few coats of minwax oil based stain (red mahogany) and now I have nice deep dark absorption on most of the wood, but the grain pattern sealed too much and is still almost a natural pine color. Tried a gel stain over that to darken up the grain, but still much lighter than the surrounding areas. So, ultimately my question is: Typical wipe on mix looks to be 1 part each poly-mineral spirits-BLO. Since it's an oil based stain, would it be ok to sub…
-
- 3 replies
- 3k views
-
-
looking for some advice on a stressed painted finish. On this current build my wife is doing a stressed finish. 2 coats white primer,2 coats historic yellow and 2 top coats of brick red. She then sands the edges and the yellow comes thru it looks cool. Well before I put some clear coats on it I was thinking I should try to wet sand? some of the scratches out in the areas that are not stressed. She got carried away with the sponge when she was sanding. She is telling me to leave it that it just makes the finish look more authentic. Any thoughts? I also noticed 3 sets of small waves in the plywood top which are really aggrivating me because i hand sanded it and didnt see i…
-
- 2 replies
- 3k views
-
-
It was recommended to put a coat of Seal Coat on the stained wood prior to the poly coat by one of the guys over at woodcraft. Overkill or good advice?
-
- 7 replies
- 6.5k views
-
-
I am looking for a technique on filling the pores of walnut. Ive watched marc's video on his re-finishing segment but im not sure either method is right for my situation. I have a blanket chest made out of walnut and leopardwood, and im looking a filling the pores of the walnut especially the top. the problem is I incorporated sapwood into the design of the product so the last thing I want to do is darken that with a colored filler or the heartwood dust if I wet sand with a varnish. Any help I can get from you guys would be great
-
- 7 replies
- 3.8k views
-
-
So... been playing around with the pre-seal stuff... trying different things... This may be coming down to my inner critic bitching and moaning again. Also wondering if I have been "over sanding." I just did a test piece where I hand sanded the piece instead of busting out the machinery. THEN... I actually read the instructions on the can of stain and applied "liberally" ACROSS the grain. Let it pool up a bit and then wiped with the grain to smooth it out. It's in the garage drying at the moment so I will try and take a pic and see if you guys can tell the diff. With the hand sanding it almost looks like the blotching (what little of it there is) on the untre…
-
- 17 replies
- 5k views
-
-
Need some expert advice before I make things worse. I have hand built a new dining table using Maple wood. To finish the table I applied MinWax Wood conditioner to try and prevent uneven staining. The next day I applied MinWax Stain (Dark Walnut) only to find out that the wood stained very unevenly. I guess I didn't do my homework very well becuase I know see online that staining Maple is considerably harder that many other woods (Most of my other projcets used Poplar which I've found stains very well after the wood conditioner has been applied). I applied a couple more coats as the first one was very light but was still very unhappy with the uneven staining. Tonig…
-
-
- 19 replies
- 86.8k views
-
-
I know you all think I am a MASTER woodworker, but yes yes I too need help every so often. So I have never finished anything before, I have made a coffee table for my wife out of red oak. I know it is a very poris wood and if I remember right it needs to be filled before finishing. Am I right or wrong? I want to stain it to make it darker because my wife likes a darker look. Please help me out here guys, I have put a lot of time into this table and want it to turn out right.
-
- 14 replies
- 12.1k views
-
-
Ok, I have almost finished my project(s) and now it's time to complete the sanding, I plan on putting 3 coats of shellac sanding in between coats with 220 grit then after the 3rd coat buff with steel wool and wax. My question is to what grit should I be sanding the wood before the 1st coat of shellac. I'm thinking that the 3 coats of shellac will fill the wood so can I get away with just sanding to a 150 grit or must I get it to 220 grit or better. Just to let everybody know there are 7 different types of wood, walnut, purpleheart, cherry, hard maple, paduak, zebra, and yellowheart. Thanks, NYHump
-
- 9 replies
- 18.2k views
-
-
Hi All, I am into sealing my first piece with Polyurethane. I used Minwax pre-stain, stained with minwax natural stain and have completed my 2nd coat of polyurethane - Minwax as well. Now, the instructions recommend that you sand with 220 grit between coats. I applied the 1st coat to 6 drawer fronts. 3-4 hours later I sanded the fronts. I started with an electric sander with 220 grit but stopped after only 1 front because it seemed like I was taking the polyurethane completely off the drawer. I hand sanded the remainder of the drawers with 220 grit and completed a 2nd coat. The finish looks better than the 1st but has some small defects such as brush st…
-
-
- 20 replies
- 7.9k views
-
-
Hi Folks... I recently made a decent little box out of cocobolo, and having had good luck with this approach on some walnut, proceeded to attempt to build up a finish using wipe-on poly. After a few coats, maybe four, it seemed like it was not drying or curing properly. It seems this has to do with the natural oils in the wood not allowing the varnish to cure. I think. And then I noticed a similar thing maybe starting to happen with some ziricote, but I nipped it in the bud after the second coat, fine-sanded it and buffed it a bit, and it seems to be stable, and still shiny -ish. But for the cocobolo box, I ended up having to sand the crap out of it to take away …
-
- 6 replies
- 6.2k views
-
-
I need to make a toner to match the top of a dresser with it's sides. I have the tints.....now what do i use as the medium? Shellac? Lacquer? Urethane? And what is a good ratio to thin it out to? Thanks
-
- 7 replies
- 8k views
-
-
Okay. Finishing drives me a bit nuts. I'm making my girlfriend a pencil holder for her office, and it took ten minutes to dimension, ten to cut, and maybe five to glue up; I'm half an hour into building the thing. So far, it has four coats of a hand sanded oil finish, and probably three more to go before I'm happy with where it is. This will take far more than half an hour. I'm refinishing a buddy's wooden countertops, and a friend recommended 10-15 coats of thinned poly. That seems reasonable, but an extreme amount of time. (I'm going with three coats of danish oil and a strong prayer.) Seems like everything that doesn't involve a spray booth... takes…
-
- 5 replies
- 2.9k views
-
-
hi all, new guy here.w i was wondering if any body has used the sikkens product cetol door and window clear finish over a minwax oil stain. I just completed a wood screen door i made for my sisters house in St louis mo..Talked to a lady rep of the company and she cannot say yes because i did not not use their product under the coating.This product is supposed to be superior to spar urethanes such as minwax helmsman.This door facing north is under a 8 foot deep 25 wide porch so it never receives direct sun or rain.Should i just use the helmsman and not worry about it?
-
- 2 replies
- 3k views
-
-
I'm building a vanity with doors where there will be a solid wood panel (1/4" thick). Should I finish the panels first before building the doors so they float in the door or should I just build them and finish all together? Michael
-
-
- 6 replies
- 4.3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·