Finishing
2,922 topics in this forum
-
I may have totally lost it now...while riding over the weekend I got the great idea to build a set of saddlebags for my '95 HD Dyna Wide Glide. I have a leather set (20"L x 10.5"T x 6.5"D) but they are small so I plan to build something more substantial (~ 22"L x 15"T x 9"D). Before I even start drawing anything, I already feel like the finish for this project could make it or break it. My initial thought is to finish the project as if I had built a boat, ie epoxy & fiberglass. Does anyone have any thoughts? My biggest concern is that 1 of these bags will be "hung" over the muffler/tailpipe. I'm a worried about the effects of heat on the epoxy finish and any s…
-
- 4 replies
- 2.9k views
-
-
Hey Everyone, I am new to this community. I decided to join because im trying to find harware for my grandfathers old directors chairs that i am restoring. I am having trouble finding the locking knife hinges that are attached to the legs and allow them to fold up. Through extensive internet research ive tryed rockler, vandykes and other websites and this wedsite, but i cant seem to find what Iam looking for. Can anyone point me in the right direction? Thanks
-
- 4 replies
- 8.1k views
-
-
I noticed a day after applying and oil based poly that I had a small drip mark then ran onto a painted surface. How can I remove the spot with out removing or damaging the painted finish. Am I just wishful thinking? Thanks
-
- 1 reply
- 2.9k views
-
-
I'm wondering what the advantages of using Waterlox on projects are vs. using some other lesser/cheaper brand of wiping varnish. I often hear that many woodwokers default to this finish in a variety of situations, but I'm wondering exactly how it compares to other brands and what characteristics make it so great. I've used it, as well as Formby's and Minwax as well as some oil/varnish mixes to throw into the comparison and to be honest i can't tell that much of a difference, much less a difference that would justify paying 3-4 times as much. I remember coming across an older article in Fine Woodworking that compared like 30 finishes and their conclusion was that the be…
-
- 9 replies
- 8.7k views
-
-
Is there an easy way to remove a bathroom counter top without tearing up all the cabinet work. I can only see 4 screws that may be holding it down, but I believe the top (MDF) has been glued to the cabinet structure (oak, oak/plywood). I am afraid it may take chunks with it. Any help is much appreciated.
-
- 4 replies
- 2.9k views
-
-
Is this a solid choice for a wooden countertop? I have also heard of people mixing mineral oil with beeswax, and then applying. Anybody try this? Also, where would a person purchase mineral oil?
-
-
- 5 replies
- 3.1k views
-
-
Not to drudge up an old topic again, but...... I'm in the process of making a custom gunstock out of quilted maple and I'm to the point of seriously planning the finish. The more I work on it, the more the beauty of the grain strikes me and I would like to preserve as much of this as possible. I had planned on using Lin-speed "Gunstock Finish and Care Oil" which is a highly refined linseed oil. Then I saw the "Popping the Grain" video. Bill White at Lin-speed said using Shellac to fill the pores will stop the action of their product. He even did a test mixing Behlens Walnut Dye with Lin-speed. He said that he preferred Lin-speed alone as it did a better job of pr…
-
-
- 9 replies
- 21.6k views
-
-
I tried to merge my last 2 posts, but to no avail. Anyway, is Shellac a good choice for a wooden countertop?
-
- 5 replies
- 19.1k views
-
-
I'm replacing all the baseboard moldings in my living room and kitchen, along with the casing around the doors. We bought stain grade moldings and I laid them all out in my garage to start staining them. My wife decided to help me by staining them while I was at work. She put 2 coats of stain on and thought it looked pretty good until she gets brought them in the house, and into better lighting. The stain turned out to look a lot more grey than brown. This might be a dumb question, but is there anyway to get it darker, or more of a brown color now that they are stained? I know the proper way would be to sand them all down and restain a different color, but that's a lot …
-
- 6 replies
- 3k views
-
-
Will pop goes the maple hve the same effect on birdseye maple as it does on the curly?
-
- 14 replies
- 3.8k views
-
-
I tthought walnut was the the stuff used for micro scratching- almond is new to me. Thank you.
-
- 2 replies
- 2.9k views
-
-
I'm going to be building a bunk bed for my boys and looking for a finish. After doing a search here first, I think I've decided to use Real Milk Paints (color not decided - yet my oldest son wants green). So I'm wondering if anyone has any advice in using Milk Paint with Douglas Fir? Should I put a white coat on first, followed by the actual color? What about a protective finish over the Milk Paint? Thanks, Michael
-
- 2 replies
- 3.7k views
-
-
I'm talking with a potential customer about building a large custom rustic style table from reclaimed barn wood. They like the "bleached" lighter color as found in these pictures from Restoration Hardware's website (See also pictures here). The table pictured is made from pine and NOT protected with a finish. My customer wants some protection on the table surface to make it more durable and easier to wipe/clean while keeping the light color. I also will probably try to use a hardwood rather than pine, depending on what barn wood I can access. Any suggestions on how best to accomplish this finishing challenge? The last picture is a collapsed local barn that I hav…
-
- 9 replies
- 11.5k views
-
-
This is what happened, I built myself a tv stand with alder and used minwax cherry 235 stain. I used dovetail on the corners and mortise and tendon for the shelves. I applied stain on the project in the morning and checked it out before I went to hit the sack. I just noticed that the dove tails where not flush. I didn't think at this moment but I got the sander out and smoothed it out to 220 grit. I applied the stain and I sanded sticks out and now it really bugs the hell out of me. Could I 1. apply the stain again but let it sit for a little longer? 2. sand the outside surface and stain again to match or 3. did I just ruin my project from a newb knee-jerk reaction?
-
- 1 reply
- 3k views
-
-
spent the last few hours learning more than i'll need to know about finishing. I've got about 4 different options for protecting my workbench: I can do straight BLO and straight varnish. I can do a oil/varnish mix (varnish, boiled linseed oil and mineral spirits) I can do a ''wiping varnish" (varnish, mineral spirits) I can do a straight varnish. I'm wondering what main differences I'm really going to see between all the options. I don't mind adding a little color but I don't want it to be yellow. I have light pine so that might be an issue. I'm leaning away from straight BLO/straight varnish unless it would give far superior results but then I have to worry…
-
- 7 replies
- 3k views
-
-
Does water based spar varnish perform as well as the tung oil based varnish? I need to finish an outdoor white pine sign.
-
-
- 7 replies
- 7.3k views
-
-
Here's a bench/big shelf I just made out of home depot wood (not sure what type of wood it is but it seems soft). Didn't put the bottom shelves on yet. Wondered what you guys thought about staining it. It will in my garage permanently i'm just wondering if I should make it prettier or leave it natural looking. Would this be the type that needs a pre-stain also what color would you go with. Post your own pictures if you want.
-
- 8 replies
- 6.2k views
-
-
Hey everyone, new guy here. Just thought I share my recently learning experience and hopefully get some advice. I haven't built anything myself yet (a quick explanation - ) but my wife and I bought a night stand from an unfinished furniture store (red oak, I think) with the intent staining and sealing it a few years ago. Fast forward to yesterday when I finally started making good on our orignal intent. Having recently watched Marc's video on pre-sealer and gel stains I got myself set up. Now, I was pretty confident I knew what I was doing and felt pretty good after applying stain last night. I had used a combination of applying and wiping with a seperate clean rags…
-
- 4 replies
- 2.9k views
-
-
Hello - I'm finishing a small piece of cherry (wood) furniture using BLO for the first time. I am three coats in (last coat 3 days old), and about half of each board is very slightly tacky (much less so than a post-it note glue strip). Up until this point I have been leaving each coat pretty wet but not dripping. (And it's starting to look great!) My questions: 1. My guess is that the fact that some of each board is slightly tacky must mean that the wood pores are getting full and the BLO will start to build a surface finish. 2. Should I wait until the oil is completely dry before putting on subsequent coats. And how wet should subsequent coats be? 3. When …
-
- 1 reply
- 4.1k views
-
-
I have some cherry cabinets almost ready for finish. My original plan was to seal several coats of shellac to get a little amber color and clear coat with lacquer. Now that I'm in a little bit of a time crunch, I'm thinking I can get the same effect using Danish oil then lacquer. Are there any comparability issues with Danish oil and lacquer?
-
- 3 replies
- 11.2k views
-
-
I am refinishing my white oak kitchen cabinets. I have applied 2 coats of General Finishes water-based stain. Over that I wiped on a coat of Bullseye Sealcoat dewaxed shellac. I had planned on then sanding before applying several coats of Arm-R-Seal. When I began to sand the shellac with 320 it immediately burned through the shellac and through the stain. I was surprised it sanded off so easily. My next idea was to try 600. With 3 strokes of the finer sandpaper the finish had been burned through. Not sure what I am doing that the finish has burned through so easily. I know the shellac was thin as I had wiped it on. I obviously need the shallac as a barrier between the …
-
-
- 5 replies
- 3k views
-
-
looking for the best way to finish a birdseye maple box.
-
- 1 reply
- 4.1k views
-
-
Anybody try this finish? I was thinking about using it for a wooden counter top. It is food safe, but have never used it. http://www.leevalley.com/en/wood/page.aspx?p=45105&cat=1,190,42942
-
- 9 replies
- 3k views
-
-
Hi Marc, I am planning on useing your mix for my front door.I was wondering if you have any updates and or changes since this was about 3-4 years ago when the video came out.My door had a thick poly film on it and was a bear to strip down to bare wood,so I am double and tripple checking my finsh scheduleI.I live in Palm Desert and get allmost the same conditions that you do.As you did I am leaving the door installed.Please tell me if I have this right. 1part mineral spirits(cant find naptha) 1part blo 1/2 part epifanes(bought the one you had a link to) apply let dry lite sanding reapply let dry lite sanding 3 and finall coat use just min. spirits and epifane…
-
- 0 replies
- 3k views
-
-
Im making a couple wooden hand planes. I would like to protect them with some type of oil or top coat. I use a lot of different finishes in the shop and want to make sure whatever I put on my planes wont effect finishing my work. Any suggestions out there?
-
-
- 1 reply
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·