Finishing
2,922 topics in this forum
-
I am refinishing my white oak kitchen cabinets, but I seem to have goofed. I am using a GF water-based stain, and I accidentally washed the bare wood cabinets with mineral spirits/paint thinner right before I was to apply stain. I realized my situation soon afterward before I applied any stain. Knowing that the mineral spirits are not going to mix with the water-based stain, what should I do to correct the situation? Can I simply apply some denatured alcohol and the issue is corrected, or do I need to re-sand etc? Also, I have read that naphtha is possibly better than denatured alcohol anyway. Dries faster? Any help at all would be greatly appreciated!
-
- 3 replies
- 13.7k views
-
-
Yesterday, I applied some Danish oil (Watco "Natural") to some pieces, including both pine and some hardwoods. The instructions said to apply one coat, wait 30 minutes, apply another coat, wait 15 minutes, then wipe off the excess. Well...I neglected to entirely follow the last of those instructions, and today, I found basically these sticky patches of apparently half dried, unabsorbed oil. I tried to wipe those up, but all I accomplished was to scuff-up those areas and get lint into the sticky stuff! :-( What's my best bet for a fix? Remove the excess with mineral spirits, perhaps? Or wait several days until everything dries, then steel-wool the surfaces until they…
-
-
- 2 replies
- 4.4k views
-
-
Hello everyone, I have a project that I am working on that uses curly red oak side panels. I would like to use a finish for them that is relatively simple. I don't want to use any stains or dyes (ie. "pop goes the maple" ), etc., because other parts of the piece that are NOT made out of curly red oak (different wood species) would be changed, and I'd ideally like to use the same finishing proceedure for the entire project. It's very important that I don't significantly change the color of some of the other woods in the piece. I'm thinking of doing a base coat of dewaxed shellac, followed up by several coats of Arm-R-Seal. Does this sound like a good way of…
-
- 7 replies
- 6.8k views
-
-
Marc, I recently watched your video about making figured wood POP. I am making a picture frame for my brother-in-law and I want to make it in two colors. He is a really big fan of the Detroit Tigers and my wife bought him a poster of an old newspaper headline from 1984 when they won the World Series. I got an Idea to make the frame Tiger striped. I thought I would use curly/tiger maple and first dye it with ebony to pop the grain then sand it down and dye it orange to look like a tiger. Do you have any recommendations for doing this procedure? I made a sample on a scrap piece to show you what I mean.
-
- 12 replies
- 4.2k views
-
-
Can you give any suggestions for a good finish on a 30"X74" butcher block island top? Beside the normal mineral oil or vegetable oil. Also do you have any better finish options for finishing cabinetry or interior trim work besides a pre cat lacquer? It works great but the smell is really getting to me. I have to use it a lot in my business and looking for more water based options.
-
- 4 replies
- 3.6k views
-
-
I want to make a few trivets out of scrap wood - is there a best way to finish them? Do I finish them at all? I am concerned with the finish holding up to the heat of hot pots and pans. Thoughts? Thanks.
-
-
- 1 reply
- 3.7k views
-
-
Hey everyone, I have a sea trunk that my Grandfather traveled with from Italy in early 1910-1912. It’s has a leather outer layer. I would like to get it restored but cannot find a place to do it. Does anyone know of a place I could send it to get done. Thanks Pat
-
- 5 replies
- 4.5k views
-
-
I have finished building a couple aromatic cedar chairs for the backyard and not sure what finish to put on them. I don't really want the weathered look in a year or two so looking for a durable finish. Any help be great
-
- 4 replies
- 3.2k views
-
-
Fuji has a new sprayer on the market. I don't have an HVLP, and have been considering getting a "mini-mite 3". The "Semi-Pro 2" is more affordable, but is a 2 stage unit. I don't really know a lot about HVLP sprayers. I've read the specs, but they don't hold a lot of meaning for me. Does this one look like a high quality unit? I would use it to spray mostly water based poly. Not sure if a "2 stage" unit is lower quality that a 3 or 4 stage unit. http://www.fujispray.com/hvlp_systems.html
-
-
- 6 replies
- 6.1k views
-
-
Hello all, Iam refinishing my front door and would like some ideas as to how to get it ready.there are many drips and globs of finish from the previous owner,and spots where the finish has started to peel.I live in palm desert and the door gets some morning sunlight and some sand blasting when windy.I was planing on useing Marc's finish from his "desert outdoor finish".I have alot of sanding to do,the flat parts are easy,but, as you can see there is 18 recessed panels with a small molding.That is what I need help with.Would a sanding mop work?(on a power drill) I dont have a curved scrapper but I would get one if it was the tool for the job.thanks for reading and any advi…
-
- 5 replies
- 4k views
-
-
Hi guys, Just finished a trestle picnic table along with trestle benches. I didn't stain the bottom of the table, benches I did though, not sure of my reasoning there. But anyhow, when I go to spar with the 20/80 min/spar, do I do the bottom also? Does this need protection as much? Thanks, D
-
- 8 replies
- 3k views
-
-
I am in the process of opening a new shop and am currently addressing my finishing setup. I just got a Coral spray booth and am looking to upgrade my spray guns. I have been told that Air assisted airless gives the best finish but I do now know a lot about them and especially which one to get. I was just looking at getting a better HVLP (Apollo 1050VR) but was told by other shop owners not to waste my time on an HVLP and just go for the AAA. I know that there are probably a lot of you who spray all the time with an HVLP without any problems and get a high quality finish. I will be primarily spraying pre-cat lacquer and vinyl sealer though the system. Any thoughts o…
-
-
- 9 replies
- 6k views
-
-
Shellac on a dinning table is a bad idea. I love the finish so much, I had to see for myself. Maybe a good coat of furniture wax will do the trick? NO. Right away upon use the finish started to show wear. I have sanded the finish to even out marks from hot bowls of soup. I had to sand and build my finish back up in these areas that now im starting to fill the grain. I want a bad ass finish, so I decided to keep building my finish to fill all the grain. I am brushing my wax free shellac cross grain, sanding smooth, and slowly filling all the grain. Next I plan to top coat with General Finishes High Performance top coat. OH, and the table is qs white oak from way back. …
-
- 3 replies
- 7.1k views
-
-
So, this isn't fine woodworking by any stretch. I'm sinking four 4x4 cedar posts into holes as part of a grapevine trellis. I ideally want a nontoxic, non-leeching preservative on those posts, to make them last longer. They'll be surrounded by gravel and/or clay, so I'm not expecting terribly wet soil stuck to them. That said, I'm trying to figure out which oil I'd least mind having to eat, as eventually, the grapes will pick it up.
-
- 3 replies
- 3k views
-
-
Hello, I just started wood working this year and I built a nice Ash bench, and I am currently building a nice cherry nightstand. I need to finish the bench so I started to look for finishes. I did some reaserch=h, I found son brush on, wipe on, or spray on poly varnish. I also found some spray on laquuer. Should I use spray on finish or stick to brush on. I want to use ethier varnish or laquure. What is the best choice of finish for this project.
-
- 3 replies
- 2.9k views
-
-
I am building an open cabinet of sorts to help organize knick-knacks, widgets & whatchamacallits in my shop. Several of the cubbies are going to be bit on the small side to finish once I assemble. Could I cut plywood pieces to size, polyurethane aall pieces & THEN cut dadoes? I'm wondering if the poly might gum up my dado set or router bit depending on which way I choose to cut dadoes. I asked the same thing on another woodworking forum & was given advise but my concern about dado set/router bit gum-up wasn't answered.
-
- 10 replies
- 10.8k views
-
-
I'm new to woodworking and I'm finishing a nightstand I made. This is my first finishing project and I've learned a few things along the way, However, I had completed three coats of water based Poly by minwax, and it was looking surprisingly good in my opinion. I had used 220 to scuff between each coat and after I applied the fourth coat I noticed It had some streaks. I start off by making sure I stir the Poly in the can. Then I poured about enough for the job in too a secondary container. I sealed the can and applied the finish. I would do this for each coat and make sure that the secondary container was clean before following the procedure again for the next coat.…
-
- 7 replies
- 3k views
-
-
Hi all, My wife and I recently worked a piece of cherry from our property into a railing for our bedroom stairs. It was quite a unique piece with a lot of knots and burls that turned out beautifully after lots of work. I'm just wondering how to finish it off to best protect it and keep it's natural beauty. I was thinking of using a natural wax of some sort like this stuff http://www.environmentalgreenproducts.com/store/osmo-wood-wax-finish-transparent-pr-16147.html. Osmo is the company but I don't know much about it and if this would be a good idea or not. If anyone has any suggestions please let me know! Thanks
-
-
- 5 replies
- 2.9k views
-
-
Hello. Do anybody have a tip on where to buy different types of moulding on the web in the states? I am looking for the normal types but also bigger and more elaborate designs. It is important that they have a online shop with good pictures. They will only need to ship with in the states, more aprox. to New Jersey So any tips? Best regards T.Robertsen
-
- 8 replies
- 3.8k views
-
-
My wife and I have a table she inherited from her grandparents which we recently received a pretty nasty stain a while back. (See the photos below.) We forgot a bag of frozen yogurt or ice cream (something like that) in bag as we were leaving for a few days. I am trying to decide the best way to repair the problem, preferably without having to strip, restain and finish the entire table (and the matching set of chairs). The main part of the stain is on just one leaf of the table. My best case scenario would be to strip this leaf down and try to match the stain but as this would be my first attempt at matching like this, I'm unsure how to proceed and whether I can indeed…
-
- 5 replies
- 4.2k views
-
-
I just purchased a sanded, albeit poorly sanded, oak bureau from the "Awakening" movement era in the US. Northampton, MA was the birthplace of this revival, similar to Selma, for the civil rights movement. History aside. The lady I got it from was obviously a substance abuser, $40 for the bureau, ie her fix, it was a crack house and had many cats in her house. See where I am going? How, besides Natures Miracle, can I get the cat urine smell out. I saw this in a garden forum and peroxide sounds harsh. Any ideas would be greatly appreciated. It's gonna go into ash heap of history if I can't get this smell out. 16 0z Hydrogen Peroxide 1 Teaspoon dishwashing liquid 1 …
-
- 3 replies
- 2.9k views
-
-
For those given to flights of curiosity: The vinegar dye in PAAS Easter egg dye kits doesn't really do anything on wood.
-
- 3 replies
- 2.9k views
-
-
This is my first time spaying a finishing. I plan to use Sherwin Williams CAB acryilc lacquer on a maple cabinet using an Earlex 5500. I'm open to any tips you might have to get me started. A few questions I have: Do you prefer a 1.5mm or 2mm tip for lacquer? Should I thin the lacquer? I've read that thinning may cause the laquer to dry too quickly so I would also need to add a retarder. The CAB acrylic lacquer data sheet recommends applying one coat of vinyl sanding sealer. I think this gives the lacquer a better better bond and reduces the chance of peeling. Anyone use this? Will it yellow over time? Thanks!
-
- 6 replies
- 18.6k views
-
-
Have a question that I'm hoping you guys could answer for me. I have made several picture frames from sugar maple for my daughters graduation pictures . For the finish, my plan was to use an ebony waterbased stain, followed by Sherwin Williams CAB acryllic lacquer (on top of a coat or two of S-W vinyl sealer). I've done this many times with good results. Except now, my daughter has changed her mind, and decided she wants the picture frames done in her school colors. Well I've used mixol color pigment before with the S-W lacquer with good results so I tried using that to come up with the correct colors. After trying many times to mix the proper shades of color, I…
-
- 3 replies
- 4.3k views
-
-
Newbie here looking for advice. In addition to this project I'll be refinishing a dining room set soon, so I'm sure I'll need some advice for that as well. Subject: Doug Fire Hand Hewn Mantle and Corbels Concern: Raised grain running down face of corbel and raised end grain Desired result: http://www.larryjwhe...album=121&pos=0 My mantle is identical to the one pictured in the link. Made by same timber company. You can see the raised grain running down the corbel and at the end. Question: How can I acheive this look? Current Path: Staining with Dark Walnut Stain to desired darkness which will be really dark. Then finish with multiple coats of …
-
- 17 replies
- 12.2k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·