Finishing
2,922 topics in this forum
-
-
hey guys i just watched the popping the maple pod cast and have a question. can you get the same effect by using boiled linseed oil for the first coat and then apply your finish coats (arm r seal oil and urethane) i see a lot of people using boiled linseed oil and was wondering thanks
-
-
- 8 replies
- 8.2k views
-
-
Hello Everyone, I'm a newbie to this forum and I'm hoping that the incredibly knowledgeable participants can help me. I have spent the better part of the weekend researching food safe sealers and I'm so confused I am refinishing a wood table and adding glass mosaic on top. I need a sealer that is food safe, as it will be used as a kitchen table. I've tried Google searching for food safe epoxy, food safe sealers, etc., but the search usually brings up manufacturers websites that list all sorts of technical stuff that I don't understand! So, simple question...does anyone know of a food safe sealer that I can use on my table top that would be compatible with …
-
-
- 11 replies
- 38.5k views
-
-
Hey Guys. I've been planning on making a baby crib and wanted your input on the finish. I want to paint it white. In the past I've liked to use generals finish milk painted topped with some coats of pre-cat waterborne laquer. Is there a paint that is more safe for baby furniture than others? Is laquer once it is dry safe for a baby to chew on? I've heard that once it flashes off and is dry most finishes are safe. I've noticed in the spec sheet for the generals milk paint there is some titanium dioxide and aluminum silicate in it. I've read about the metal dryers are not good to have in the finish. Should I try the powder milk paint instead? Thanks in adva…
-
- 1 reply
- 4.7k views
-
-
Ok, so here's the deal. My parents want to replace their kitchen countertops. They don't have the money to start from scratch and my dad wants me to remove the old laminate and then put down new. Is this even possible? If it is what is the best way to do it? Any advise would be very helpful. I realize this isn't exactly woodworking, but thought I would give a try here.
-
- 11 replies
- 6.4k views
-
-
Greetings!, new to the forum and anxious to get started. I am a first time homeowner and just picked up a teak table. The table has two self storing leaves and is in generally good condition except one spot that is damaged. I am interested in what I should do now to keep the wood in good condition, and then knowing what I could do to refinish the table in the future:
-
- 1 reply
- 3.8k views
-
-
Could I get some mid to lower end recommendations on sprayers? Or, what a fella should be looking for? Now, I suppose that could mean that folks could give me their thoughts on if I go to HF and get the crappiest thing they have and it is great, it's what I put in the sprayer that makes the difference. OR You could tell me that I could get the best finish ever but in a junk sprayer, it is worthless. You could tell me that it isn't worth getting until I can get a top of the line sprayer. I'm thinking of starting to spray finish some of my pieces, but a sprayer isn't the highest thing priority on my budgeted tool list. This is the beginning of my research, so I …
-
-
- 14 replies
- 9.5k views
-
-
I have a few pieces of wood floor samples that I think would make an awesome box. The plan is to use this wood for the sides and frame for the top and spalted maple veneer panel in the top. Something like this: I think the wood is Kempas; or possibly something entirely different altogether. The grain is beautiful dark flowing lines on a deep red background. When I ran the underside on the jointer, I got this: There is definitely some red in there and I can see the flowing Angel-Hair like lines in the grain, but that dark black isn't there. I assume there is a dye or stain on the surface, but how do you get the black lines? I've thought of filling the por…
-
- 25 replies
- 8.8k views
-
-
I'm really angry about this. They said it's not green enough! I don't like using flotral and latex. I like oil! What the hell!
-
- 5 replies
- 4k views
-
-
I'm new to the whole wood working process. I decided to refinish a 5' x 8' slab of walnut, put legs on it and make it into my new dining room table. I've done a couple of other tops out of walnut where I sanded and then finished them with urethane. They look fine to the average eye. This slab is very figured with a lot of marble and curl and has the potential to be stunning - as long as I don't screw it up. So I really want to do things right when it comes to finishing off the top. I've been practicing on the bottom side of the table so far to get it ready to be sealed and have the legs put on. It had a lot of saw checking, so I sanded it down with my belt sander. Then…
-
- 3 replies
- 5.9k views
-
-
Dear Friends, I would like to know if there is a problem (health, looks, drying time, etc) using exterior polyurethane indoors? I want to apply polyurethane to a wood that will be indoors (bedroom) but in the sunset some sunlight enters the room washing part of the wood. I am concerned about partial discoloration because of that sunset sunlight. Thanks.
-
- 5 replies
- 16.2k views
-
-
Hi friends!, I am new to woodworking, love it!... I am located at Panama, Central America and here we have lovely nice wood but few finishing products we can choose from our stores. I have found one store to have 2 options for wiping finishes (I prefer to go this way for now). I would love your comments about only this 2 products (I know, I know its a kind of restrictive) but I just have access to this 2 and I dont want to mix my own. I have read a lot about wiping varnish and oil/varnish blends. But I want the opinions for more advance masters as you all are. 1. Minwax Antique Finish 2. Formbys Tung Oil Thanks.
-
- 2 replies
- 3.8k views
-
-
I'm planning on building wooden toys for my son, and want to see if you could offer an advice on finishing. I plan on painting the toys with a mix of spray cans and brushed acrylics. What would you suggest to use as a final clear-coat? I would like something that would last under rough play and also be safe to be stuck in a mouth from time to time. Any input is greatly appreciated. G.
-
-
- 8 replies
- 19.4k views
-
-
I have a Seltz tabletop that has seen better days, Can I get some recommendations on how to fill the cracks and what type of finish to use. The table came with a 150mL container of Linseed oil/Beeswax mix. I live in Alaska and the lack of humidity is hard on solid wood. Can I make my own linseed oil/beeswax mix? If so, how? Or can you just use butcher block oil?
-
- 1 reply
- 3.9k views
-
-
I'm in the process of making some wood working tools out of merbau / brass /stainless steel. I'm a bit unsure of the best finish for them. Ideally I'd like some glossy look but lacquer probably won't stand up to wear and tear so good. I see some people use wax but from what I've been able to google that's not so tough either? That leaves, oil? The assortment in the local hardware store is pretty slim. I think they have boiled linseed oil and possibly teak oil. Would any of those give a good result or is there somehting else I should look for? I have some decent epoxy and glossy/matte CAB lacquer that I use when making fishing baits but I don't think that would stay …
-
- 4 replies
- 2.9k views
-
-
I ran out of Enduro Pre-Cat Urethane, darn. I have lots of Enduro-Var. Can I lay it over the Pre Cat?
-
- 1 reply
- 3.1k views
-
-
I put a coat of GF arm-r-seal on a project yesterday. i want to hit it with 0000 steel wool and put my next coat on but im not sure how long i need to let it set up in between coats. what's a good rule of thumb? it is inside a room approximately 62 degree temp. btw, the wood is walnut if it makes a difference.
-
-
- 8 replies
- 13.4k views
-
-
Hey guys I hate waiting for my projects to dry after applying finishes and I have heard of some high shiny friction finishes, does anyone know the names of any of these or where to get them? Thanks
-
- 4 replies
- 2.9k views
-
-
OK I have some sanded pine plywood I want to stain in the very near future. I am going to be using Charles Neil's blotch control and General Finishes water based dye. So my question is this on top of it I want a polyurethane film type finish. I am seriously considering using General FInishes waterbased urethane or varnish products - either their High Performance Polyurethane Water Based Top Coat or their Endurovar Water-base Polyurethane Varnish Does anyone have experience with either of these? My preferred method of application is to wipe it on so I would like for it to work like what I usually mix as a wiping oil varnish with equal parts oil bas…
-
- 2 replies
- 3.4k views
-
-
can boiled lindseed oil be covered with a water based poly?
-
- 13 replies
- 4.5k views
-
-
Hey guys, I haven't posted in a while, but my dad and I just got av hvlp and were wondering what a favorite top finish to spray with these unis is. We have no experience with these and would like any tips or suggestions you are willing to offer. It's only a cheap (rockler) unit for a starter setup before shelling out$$$. We like to finish many pcs at the same time and this would save a lot of time once we learn the proper way to use it. I have always got the answers I need from fellow woodworkers like you, so thanks in advance. P.S. If ot helps, we usually stain with minwax oil base with a rag. Never tried water based or gel finishes. Thanks Bob
-
- 4 replies
- 3k views
-
-
I love Minwax brand oil stains. My wife is very, very sensitive to the smell. In good weather, I stain in the garage. But now in the winter, I have to stain in our basement workshop. My wife is unhappy about this. What can I do to mitigate the smell? Here is what I know/think: Normal HEPA filters don't touch it (in my experience, they seem to make it worse (because of the air motion?)) Installing a hood would be the best solution, but I fear that would be too expensive Putting the rags and brushes, that I used for the staining, into a sealed can after the work helps It looks like, maybe, a charcoal-enhanced filter can help, but quick Amazon survey shows these to b…
-
-
- 8 replies
- 30.7k views
-
-
Hi guys need some help here I have a heated shop set at 65 degrees and made some nice pens and a razor kit on my lathe the other day. After my sanding I used some mineral oil in between my standings and finished it with minwax poly I gave it two coats and four days later it's still tacky and not dry did I take a wrong turn putting the mineral oil on in the beginning? Thank any feedback would be appreciated
-
- 4 replies
- 2.9k views
-
-
I'm looking at get a sprayer and not ready to spend a lot of money. Earlex 5000 or 5500??
-
-
- 16 replies
- 7.4k views
-
-
Can I spray polyacrylic water based top coat? (null)
-
- 3 replies
- 2.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·