Finishing
2,922 topics in this forum
-
Hey Marc, I just did a set of built-ins for a customer and made the mistake of using SW Acrylic Latex semi-gloss. So, now I've got the blocking issue I'm trying to get rid of. It is my understanding that I can topcoat this with a water-based polycrylic to solve this problem. So, any advice on this would be appreciated. How long do I need to wait before topcoating? Your thoughts on using Minwax Polycrylic? I'm not a huge fan of Minwax but this is readily available locally. Finishing in place (customer's home) so will I get good results with a brush? Thanks again, Ken
-
- 3 replies
- 8.2k views
-
-
Ok, I had a friend come to me tonight with a finish problem that I don't know the answer to. He has hardwood dining room table that his daughter used as an ironing board using one of those ironing board mats well the mat got hot and now the finish under the mat got cloudy as seen in the picture bellow. Any ideas how to fix this without stripping and refinishing the whole table? Thanks Mark Maslonkowski
-
- 8 replies
- 3.5k views
-
-
I had my first major setback yesterday while I was trying to polish a finish. I've been working on a Crokinole board for awhile trying to get it finished by Thanksgiving. I was almost done, just polish the playing surface and a few other finishing touches, and I went straight through the finish to wood while trying to level the surface. At this point I'm just going to sand everything off (hopefully without going through the veneer on the plywood) and try again. But I would like to find out where I went wrong here. A month ago I applied about 9 - 10 coats of a 50/50 wiping varnish. Some of the coats were fairly thick but everything still looked and felt pretty level be…
-
- 5 replies
- 5.8k views
-
-
ok i want to polish up some of my turning to give it a super shiny look but i dont know anything about using a buffing wheel. does the compounds at menards or lowes that says for metal on the label work on wood? and there is two different kinds of wheels one that is stitches together so it is stiffer and anther that is loose how does that make a difference?
-
- 1 reply
- 2.8k views
-
-
Hello all, I have a situation that has me a bit stumped. I have made a silverware chest from what i think is lacey oak but I am not sure. ( made from pallet wood) It has keyed miters and feet made from cocobolo and an inlay of a cluster of grapes on the top. The grapes are kingwood and the leaves are Wenge. I have started to finish it with tung oil. Here is the problem: the tung oil drys very well on the oak and wenge but is seeming to take forever to dry on the cocobolo and kingwood. (cocobolo more so than the kingwood) Is this due to the oil in these woods already or is it their density/porous nature? Will it dry eventually? I hope all is not lost because I am …
-
- 5 replies
- 5.4k views
-
-
I've been using the Gf Milk paint in my Earlex 5000 to spray my finish. Even though I've tried to keep it pretty clean there are areas, particularly under the cup lid, that have dried paint on them and I can't seem to get it to come off. I noticed the General Finishes offers a gun and brush cleaner and the MSDS sheet stats it has water and ether in it with a little bit of alcohol. What have you guys found to clean your gun after spraying paint with it?
-
- 4 replies
- 5.5k views
-
-
I've always had this problem. I have a spray booth with fresh air being blown into the space with a filtered fan and dirty air exhausts out the window. I use a HVLP conversion gun and there is over spray which is picked up by the moving air. In confined spraying areas like inside a drawer box, there is a lot of spray that goes into the air. My polycarbonate safety glasses must have static because they tend to accumulate the over spray and I need to wipe them off after a session so I can see clearly. The material that gets on the lenses is a dust so it is dry. Is this a common issue?
-
- 3 replies
- 3k views
-
-
A few years ago a friend of mine imported a bedroom set from Italy. I was immediately impressed, especially with the finish. It was so smooth and flawless, it almost appeared as if the wood was coated with glass. Last year I was vacationing and stopped in Florence. I randomly walked into a furniture store and the whole place was full of pieces with the same finish. From jewerly boxes to large tables, it was all finished the same way. I'm thinking there must be some sort of polishing involved. A: does anyone know what I'm talking about? B: what's the material/technique that results in this finish? Thanks!
-
- 0 replies
- 2.9k views
-
-
I’ve posted a written review and my video review of Charles’ blotch control on my blog. Overall its a great product. Easy to use, non-toxic and it just plain works. http://www.thedustydeveloper.com/2011/10/review-charles-neals-pre-color.html
-
- 1 reply
- 5.8k views
-
-
I'm building a bed out of MDF and ply for a child and she wants the bed painted white. I've tried painting shelves in the past with a quality latex paint only to find everything gets stuck to it. What type of paint is recommended for this kind of application? If I spray some polycrylic over the latex would that work? Second question: We saw a piece of furniture at the store that was white and super glossy. It looked almost plastic. How could a achieve a finish like this? Is it just many coats of a glossy polyurethane? Ps. I'm new to woodworking so sorry if these are stupid questions! Thanks!
-
- 11 replies
- 18.9k views
-
-
through no fault of my own(punk kid) my wood turned pen had the ink break and now the pen has got a few stains on it from the ink cartridge. what is the best way to clean it up and shine it up again? i took off most of the ink, should i use some 320 sandpaper and sand it down some or is there a better way? would like to get back to brand new condition so i can basicly rub it in this individuals face since he broke it in spite of me.
-
- 4 replies
- 3k views
-
-
The wife found a entertainment center she likes that i'm building and the other day she came across a finish that she liked on the general finishes website. It's an antiquing style of finish utilizing a millstone white milk paint base with a vandike glaze. I've never used the milk paint before and I would like to use my earlex spray gun to spray the paint. So has anyone sprayed this paint before and if so how were your results? did you thin the paint or add any floetrol and if so to what ratio worked best for you. Any advise would be greatly appreciated. thanks.
-
- 9 replies
- 18.1k views
-
-
Members, I am looking for some advice on the techniques you folks use to apply Shellac to a project. I like the fininsh but I am not getting the results I suspect the rest of you are. Luckily, these are projects that are going to be used at home (so far)... What is the best way to apply Shellac to a project? Do you get the best results from using brushes, foam brushes, rags, ....? I have used all of the above and combinations thereof as well. I still see small ridges (usually near the edges) that appear to be where the Shellac ran just a bit and I didn't catch it. These ridges happen no matter how careful I seem to be. Am I missing the boat on the applicat…
-
- 8 replies
- 12.4k views
-
-
Just remembered this and thought I would share. Back in the late 60's or early 70's, Popular Mechanics, did an article on using TSP to remove paint. You take TSP and dissolve in water, and heat up hot, but below boiling. Stick whatever you want to remove paint from, in the mix. Don't leave it in very long, or it will soften the wood. Take it out and brush 10 or more coats of old paint right off! I've used it a number of times. Years ago, I mentioned it to a friend who was doing a lot of exterior restoration work on Victorian houses. He tried it. He liked it so much, he had a lagre shallow tank made that would hold a door, with a propane burner under it. Big loovered …
-
- 4 replies
- 4.2k views
-
-
Customer wants a finish that he doesn't need coasters for - like a bar top. Having shown him and his wife a sample, his wife doesn't like that it looks so thick and glossy. What's the best finish that is hard and can take a little water but doesn't look like you encased the wood in plastic? Also if it is self leveling, that would be nice, sine I have one minuscule bubble in the ribbon mahogany veneer that I'm hoping the thickness of the finish will eradicate. Thanks!
-
- 7 replies
- 4.1k views
-
-
Hey Guys Well I got my nephew's cradle stained last weekend and it really looks great. I went out to look at it today and I noticed a couple little spots where I didn't get all the excess wiped off the surface and it has now dried on the surface. It was almost a week ago that I applied the stain, so it's pretty dry at this point. Is there an easy trick to re-moistening the stain so I can remove the stuff from the surface? I've seen recommendations of using mineral spirits and paint thinner but I was wondering if there's some kind of standard technique. It seems to me like paint thinner might be a little abrasive. Not sure about mineral spirits.. I should mentio…
-
- 5 replies
- 3.3k views
-
-
This isn't exactly a woodworking question, but I thought this might be a good place to find an answer. I'm looking for a finish that won't be damaged by solvents such as turpentine and alcohol. I'm working on a manufacture project producing lava lamps and two of the fluid components are turpentine and isopropyl. The cap for the glass vial is to be pour molded from epoxy that can be dissolved by turpentine. Hopefully there is something i can use to chemically seal the epoxy in order to protect it from the solvents in the fluid mixture. Thank you in advance to anyone who can help me out.
-
- 8 replies
- 15.3k views
-
-
I would like some ideas on how to fill the grain/pores on open wood... I believe that is what is is called... pores? grain filling?
-
- 3 replies
- 3k views
-
-
Hello, I am in the middle of refinishing all of the doors and drawers in my entire kitchen. I am using an oil base stain from Sherwin Williams and finishing with Arm-R-Seal semi-gloss. I had all of the doors stripped professionally to save some time. I sand everything down using 150 grit and sometimes use 220. After I use a shopvac with brush attachment to pull out the dust. The cabinets are made of oak (very old, about 30 years or more). The stain is penetrating pretty well, but it does not dry very well. The directions on the can say a finish coat can be applied after only 1 hour dry time, but I have not tried that. I let them dry at least overni…
-
- 13 replies
- 10.1k views
-
-
My father wants a garbage unit in the kitchen. He wants the base white (matches the molding) and the top a maple butcher block. I am thinking of using birch plywood. Does it paint well? Any tips or tricks? What type of paint to use? Do I have to edge band or can I paint right over the raw edge? my alternative route was to make out of pine or oak but I like working with sheet goods.
-
- 8 replies
- 17.5k views
-
-
I'll bite with a first topic.. Most tips on repairing veneer I've seen involve chipped veneer. What are people's strategies for dealing with sanding through veneer when refinishing? Not that I've ever done that before or anything.... I'm just saying
-
- 4 replies
- 8.9k views
-
-
What is the best product to use? I plan on doing a natural stain or oil but what is the best top coat. I would like something low VOC if possible. -Chuck
-
- 4 replies
- 3.3k views
-
-
Hello, I just apply some walnut stain (brou de noix in french, not sure of the translation) on a maple table top. the problem is that I'm getting this as a result: As you can see, it's one board only! What can I do to repair this? Thank you, SPP
-
-
- 12 replies
- 5.9k views
-
-
- I was putting a coat of a dark minwax stain on an oak shelf I was finishing last night and it looked perfect. When I wiped it off the bottom side of the board (after it had been on for about 5 minutes) the color was way too light so when I put it on the top side I left it on for about 15 minutes to give it more time for the color to set in. The shade was perfect but the stain had turned into syrup and wouldn't come off. I left it to dry all night but it was still a thick and sticky syrup this morning. - I used a 2:1 combo (stain:mineral spirits) - To try and make a hard surface on this mushy surface should I use a combo of Polyurethane and mineral spirits or …
-
- 1 reply
- 3.1k views
-
-
I'm currently building a cradle for my new nephew (due in 2 week! Uncle Nate is excited.. ) and I ran into a strange issue that I've never heard mentioned before. This is my first major project so it could very well be something simple that I don't know, but that's what learning's all about I guess. Anyways, my issue here has to do with some black spots that showed up on my project. What happened was I started sanding my project up to 120 grit. I sprayed it with a little water before I went to hit it with the 220 grit. About 2 or 3 minutes later black spots started appearing all over my project! I've attached a couple pictures to show what I'm talking about. The t…
-
-
- 7 replies
- 3.7k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·