Finishing
2,922 topics in this forum
-
Hi all! I have a nice HVLP set up but I am looking to start spraying water born finishes and I plan on doing so with a new gun. My dilemma is should I buy the the gravity feed cup or the siphon cup? I am not sure of the advantages of the gravity fed one as I have only used the siphon cup versions, any help in this would be great, Thanks!
-
- 7 replies
- 3.2k views
-
-
How does everyone go about softening the edges of their projects? I find if I try and sand them, I do it uneven? Am I doing it wrong. On larger pieces I use a roundover bit, but my current project has 1/2 inch slats and an 1/8 inch round over seems to much.
-
- 8 replies
- 26.2k views
-
-
Greetings all, this is my first posting. My name is Doug, I live in Phoenix and have been wood working for about 15 years now. I have never sanded thru veneer until today. I am making a flag stand for the Valor network where I work out of solid and veneered walnut, I have sanded thru the veneer and have bright little yellow strips in a couple of places where dark walnut should be. I perused the 11 pages of finishing here and didn't see anything on repairing a sand thru on veneer. Things I have tried, ink, magic markers, fill pens, stain and it all seems to roll off the strips. Any help would be greatly appreciated. Thanks, Doug in AZ. (aka woodguyi)
-
- 4 replies
- 3k views
-
-
I'm new to woodworking and have a lot to learn. However, I'm working on a mahogany sculpture and having trouble with the finishing. I want to add an ebonized section to the wood and not sure how to do it. For example taking a plank of mahogany say 24" wide and then adding a 3" ebonized stripe down the middle. I'd like to get crisp sides, so would I use dye and does dye bleed? How can I allow the grain to show through the dye or other color technique but still be "ebony". I plan on finishing the rest with a clear seal-coat dewaxed shellac (I think). I'm trying to put some depth/richness in the wood and want a semi-polish look so hopefully the shellac will work. S…
-
- 0 replies
- 3.7k views
-
-
Is it possible to put a spray on hi gloss acrylic over wax or will there be chemical problems. I used Howard feed n wax and then i used minwax past finishing wax. Or can anyone recommend a finisher or recipe that is wipe on/oil based/hard protection/glossy.
-
- 3 replies
- 4k views
-
-
Hi all. I am thinking about making an outside bar using natural edged cedar planks. The area it will be in is covered, but am wondering on what type of finish/sealer to use that will make it a durable product. For an inside bar I would use the bar finish of course. We live in South Texas and have quite a bit of humidty to deal with also. Any suggestions will be greatly appreciated. Thank you Gayle
-
- 4 replies
- 4k views
-
-
I'm just now starting to "play" with woodworking; I seem to really like the visual appearances of different species of wood; do certain kinds of finishes affect differing species of wood in predictable ways?
-
- 1 reply
- 3.5k views
-
-
I recently finished building a small Jewelry box for my daughter. Had lots of firsts for me: Bolivian Rosewood - Beautiful, brittle Completed everything except resawing with meat power. Hand cut dovetails - Turned out... ok Shellac "Rubbed out" finish This last item is kicking my butt. I brushed on 6 coats of a 2lb cut of garnet shellac sanding with 320 between coats. I waited a week for the shellac to totally cure. I then progressed through 400,600,800,1000,1500 grit paper followed by medium pumice. I would have progressed through fine pumice and rottenstone, but at this point I realized something was wrong. After the 400grit I noticed some…
-
- 4 replies
- 9.4k views
-
-
I hope someone here can help me.. please Im in the process of remodeling a 140yo house and just began work on the floors. The floors had been covered up for years with linoleum in one room and overlayment and vct in others. I just finished sanding this room with a 60 grit getting ready to go back over it with finer grit but wanted to get an idea of what it was going to look like ... since i planned on just using a poly i figured wetting it a bit with a cloth would bring out the color and grain to see. First off I havent a clue what kind of wood this is if someone could help me there i would appreciate it. But my real problem is the floor has light spots throughout …
-
- 5 replies
- 3.4k views
-
-
Anyone have experience finishing cherry with Good Stuff wood finish? I am completing my latest project -- a cherry end table -- and a woodworking friend recommended using Good Stuff since i want to keep it as natural as possible.
-
- 3 replies
- 4.2k views
-
-
I am making a teak credenza to go in an office with 1950s Danish Modern teak furniture. Natural finish appearance. Any recommendations for a finish? The top will have audio components (turntable and tube amplifier) resting there. Inside for vinyl albums on left and CD changer on right. I've heard the expression "Danish" oil and probably have even bought such stuff. Is that a specific finish or just a "marketing name" which covers many finish types. Thanks
-
- 5 replies
- 4.5k views
-
-
Ok, this is a question I probably already know the answer to but curious to hear your thoughts. The skateboard is a longboard and will be used for casual riding, no tricks or grinding, etc. I assume something from Epithanes is the best choice for this and I plan to order some for future builds. For now though, I have two choices; Armor Seal which I love and use all the time or GF Enduro Var which I have not used but I think is supposed to be more durable. Which should I go with? Is Enduro Var really more durable? Thanks for the help. Josh
-
- 2 replies
- 9.4k views
-
-
I am just about finished building a coffee table and end table for me living room using poplar. I used poplar because its cheap, and I am new to woodworking. I decided I am going to use dyes to add some color. But honestly I have no idea where to start. So is there any good books, and/or videos you guys have used to get accustomed to mixing dyes to make different colors? Like I said, I have no idea where to even start.
-
- 4 replies
- 3.2k views
-
-
I am applying the finish to the top of my project and I'm getting waves in the finish. By waves I mean theres sections where its glossy and then section where it looks like it still dry. Like hills and valleys. I am using a raking light, putting on an even coat, I just don't understand what is happening. I can get some pictures when i get home from work later today if that would help. I just kinda want some opinions on what I should do. Of course the rest of the project finished pretty well and now it starts to screw up on the top.
-
- 8 replies
- 4.2k views
-
-
Need a bit of input here. Just bought some rough cut cedar to put in wife's closet. Will plane the cedar for a smooth finish, but I want to see if there is a finish I can put on it that will still allow the aroma of the cedar to come through and the finish MUST NOT stain or damage any clothing that touches the wood. Pretty sure I would finish both sides of the cedar before I put it up. Thanks Rodney
-
- 3 replies
- 3.3k views
-
-
Hey Everyone, I am new to the forum and pretty new to woodworking. I am looking for some advice finishing a project. I am making a pair of speakers. The cabinets are made from MDF, which will be veneered with a paper backed flat cut walnut veneer, using the iron on method. The veneer has a very nice grain pattern, relatively open pores, and a pretty blah grey color. I used the same veneer for a prior project and experimented pretty extensively with finishing options. The last project was finished with seal-a-cell and arm-r seal. After quite a few wiped on coats the color was nice (though I might prefer something a little darker) but I didn't much ca…
-
- 3 replies
- 4.7k views
-
-
I have some solid brass hinges that I need to darken to closer match some pulls. Has anyone tried this before? I found these instructions, but I want to see if anyone has a better way Here are the hinges And these are the pulls. I am trying to match "A". Thanks in advance, Jonathan ==============================================
-
- 4 replies
- 9.2k views
-
-
Hi! This is a gray area on the forum as nobody has brought this up in the finishing area yet. I have a feeling that the forum is for 'fine woodworking' and not really house maintenance, but feel like this could also be applied as many of us making outdoor furniture. I've recently taken on the task of building a sliding glider from the woodworking magazine and it would be good knowledge on how to finish this as well. Anyways, my question is that I have about a 200' western cedar fence in my backyard that I'm looking at staining. The fence is about 5 months old and still looks new. It hasn't grayed, doesn't have much dirt on it, or anything like that. My first qu…
-
- 5 replies
- 4.1k views
-
-
Hey Peeps.... Yet another kitchen cabinet finish question here.... I am in the process of making some European style kitchen cabinets. My choiceof Door and Drawer face material is Alder. Inexpensive, light and very easy towork with. The finishing process I had planned to use was a 3 step process... 1. Boiled linseed oil 2. Amber Shellac 3. General Finishes Enduro-Var Water-BasedUrethane I would appreciate any thoughts if this finish is too much or would simplecoats of some GF semi-gloss be enough. I wanted to tint the wood just a tadwith the Oil, then seal the oil with the shellac while adding a hit of amber toease the light green…
-
- 3 replies
- 5k views
-
-
I am in the finishing stages of a walnut cabinet, and I have 2 coats of arm-r-seal gloss, 1 coat of semi-gloss. It just doesn't look right to me. My test board looked fine. I am thinking about giving it a coat of satin to knock the gloss down, but I am afraid it will go to far. Is there anyway to go back if It doesn't meet my expectations? Thanks for all your help in advance.
-
- 5 replies
- 3.1k views
-
-
OK. I have finished my latest guild build, the Wall Hanging Cabinet. The entire time that I have been building this cabinet, my wife has been wanting me to turn it Ebony. So......I finished the final fine tuning to the doors and drawer, then went to my local Woodcraft store and purchased the General Finishes Ebony Dye Stain. I thought after watching the "You and Dye" video that Marc made, I should give it a shot. Let me first mention, that I tryed my best to talk my wife out of turning the cabinet BLACK, but there was no changing her mind (for all three months that it took me to build it). Anyway, I spend a whole night in the shop dyeing the cabinet. After SEVERAL coat…
-
- 4 replies
- 4.7k views
-
-
I build wood geared clocks and have been thinking about making the gears looks a little more metal like with maybe some bronze and copper powders in a stain. Has anyone done this before and how did it turn out? I do not want the gears to be bright metal colored just have a hint of aged bronze look to them. I found another clock maker in Russia but the translation is completely lost between responses. The video of his clock can be seen here http://www.youtube.com/watch?v=zrF70MW7c1c Jeffrey
-
- 1 reply
- 3.7k views
-
-
I had my first experience spraying General Finishes Milk Paint yesterday with my Earlex 5000 and am having a heck of a time getting all of the paint out of the inner workings of the gun. I rinsed it with water but there is still a considerable amount of paint caked in the spray nozzle and in the tube connecting the pot to the nozzle. Does anyone have any recommendations on the best way to clean this out without damaging the gun itself? Thanks.
-
- 2 replies
- 4.2k views
-
-
Currently I'm working on a bed. I'm making it from cherry. The dimensions for the side rails, the ones that support the slats under the box spring, are 1 1/2" thick 6 1/2" wide and a length of roughly 78". Not really wanting to spend the dough on 8/4 cherry, even at my employee discount price, to plane away 3/4" of an inch of it when it's more structural than anything else and not really seen so I'm planning to use poplar however I would like it to at least somewhat resemble the primary wood in color. I'm finishing the cherry parts of the bed with Arm R Seal. Not staining it, preferring to let the wood age to it's own rich color over time. Most of the stains, both wate…
-
- 9 replies
- 11.4k views
-
-
Hi everyone I am half way through my major work for my HSC. Im making a circular Huon Pine dinning room table and am sending the top away to be drum sanded. was wondering what people thought the best finish would be for Huon Pine. I have read else where that it is good to use a wax to allow for the huon aroma to pertrude, but was looking specifics.
-
- 0 replies
- 5.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·