Finishing
2,922 topics in this forum
-
I'm getting near the end of my workbench project. Still need (or want) an end vise. the top is Oak, stretchers are pine and the leg vise is ash. I read in a book to finish it with Linseed oil to avoid making the top too slick. Unfortunately it is slick. I used Raw Linseed oil. The store had raw and boiled (I flipped a coin). Should I have chosen the boiled? What's the difference? Thanks, Brent
-
- 5 replies
- 7.3k views
-
-
I need to fix up a door in my house that has some scratches in it that have gone through the topcoat and the stain into bare wood. I have had good success in similar situations by just applying some stain and then following it with a coat or two of polyurethane and living happily ever after. The new stain hides the scratches, but doesn't have much effect on old topcoat, and then the new topcoat makes everything look shiny and new again. So far, so good. Except on this one door, some goofball (not me, believe it or not ) put some polyurethane over the scratches. As a result, it doesn't work to try and stain them. I guess one solution would be to sand through the…
-
- 5 replies
- 3.3k views
-
-
Has anyone put a clear satin or semi-gloss urethane over tung oil treated Cedar Mantel? I have put on about 4 coats of the tung oil, the color looks great, however, it just doesnt have the sheen i am looking for. If I apply a coat or two of the urethane, will that help? I just dont want to ruin the tung oil finish. I guess maybe i should have started with a blend, but too late now! Thanks for any suggestions.
-
- 2 replies
- 6.5k views
-
-
I got into a refinishing project recently the table top and the seats were clear coated and the legs and backs of the chairs were painted white. Decided with the customer that a dark stain on the clear surfaces would be good for her and to paint the legs and trim black on the table and chairs. Troubles started with removing the clear coat never did figure out what it was but it was hard as all get out tried stripper and sanding and scraping. Wound up with the monster belt sander on the table top with 60 grit to get it off. That part went well. used dark walnut to stain the Asian Oak to a nice tone she likes. Next came the painting of the chair legs and backs. Sanded t…
-
- 0 replies
- 3.7k views
-
-
I recently purchased a Fuji turbine set up(based on this forums good advice). It works great, I just had a question about cleaning it after use. I have been spraying lacquer, and I usually just run laq thinner through it when I'm done spraying. The gun came with a pretty good cleaning kit with all sorts of different brushes and things. What should I be doing w/ these? What parts should I be cleaning? Thanks.
-
- 1 reply
- 3.5k views
-
-
I love shellac... it's fast and beautiful as a finish. The best shellac formula was made by zinnser... bullseye french polish. Unfortunately, they no longer sell it, because one of it's key chemical components made it a bit pricey. ISOPARAFFIN "To make this premixed formula, Zinsser used dewaxed super-blond shellac flakes and added isoparaffin, a highly volatile oil, as the lubricant. The paraffin oil evaporates within an hour or two, negating the need for the clarifying step crucial to a traditional French polish." My question for all you woodworkers with a degree in chemistry (yes, Mr. Spagnuolo).... Where can I get isoparaffin so I can make my own shellac m…
-
- 2 replies
- 8.2k views
-
-
I just purchased the Beall system. I should have it up and polishing by the weekend. I'm really excited. My question is, moving forward, how does one polish the inside of a box? Am I correct is assuming that I should polish before the glue up? I usually sand to final grit before glue up. I'm just wondering if I accidentally polish the joint (say a miter), is that going to prevent the glue from adhering? Could it actually improve it as the end grain won't wick the glue away? or should I get the bowl buffers and use that on the inside? If that would get into the corners. Thanks!
-
- 4 replies
- 4.1k views
-
-
-
I have a shelf that I'm building out of birch ply for a client, and they want it painted with white latex. I know. It's not my favorite thing, but the customer is always right. They just happen to have a few gallons left from when they painted the walls and want it to match. Oh, and the shelf is one of those thick "floating" designs, so it's basically a big cube with all sides mitered so there is no end grain to worry about, just the ply surface. Anyway, anything special I need to do to the ply before putting on the paint? there will be a bit of filler here and there for voids and such, and obviously I don't want that or the grain to show through. Do I just use a ba…
-
- 5 replies
- 4k views
-
-
I just bought a spray gun for my compressor... wondering what size tips i use for what medium. tips for spraying? adjustments?
-
- 8 replies
- 8.8k views
-
-
Hi Everyone, I am working on a fireplace mantel for my basement. I am not quite sure how to get the best finish out of it. I am looking for rustic look, but want it to look somewhat finished. I will be testing a piece with tung oil and teak oil to see what it looks like. Can you add a layer of urethane on top of these, or will they be "shiney" enough alone. Also, does anyone know of a hand rubbed walnut colored wax? I saw a picture of a cedar mantel finished with this and it looked really nice. If so, how do you finish with it. Thanks for any help.
-
- 1 reply
- 9k views
-
-
hello, i have never used oil based stain, the only reason i did this time was due to not reading the lable. was more interested in matching the color on the samples they had.built a computer desk out of pine sanded the heck out of it , applied a coat of stain, sanded again, applied second coat. have the color i wanted to get, but it did dry with a little bit of a sheen to it, the finish is kind of rough to the touch, if i give it another light sanding could i just use butchers wax on the finish, or do i need to use some thing else. thanks
-
- 2 replies
- 8.8k views
-
-
Does anyone use sanding mops? What kind of experience do folks have with them. As they do not seem to be readily found, I am suspecting that reviews aren't great? Maybe they are just a hidden gem? Love to hear what people think.
-
- 4 replies
- 5k views
-
-
Just a quick question, because I don't think I quite understand how a finishing wax works. I was making a little box. I finished it with a few coats of Danish oil. I let it dry for 4-5 days. It looks fine. I was looking for a little more shine and a little harder finish. So I got some finishing wax. I rubbed it in and let it sit for about 10 minutes, maybe less. then, I took a clean rag an buffed it off. It looked perfect. My question is about what happened next. After I buffed it, it still felt tacky and would still hold a fingerprint. So I rubbed it down again and hoped there was some drying aspect I didn't get. This morning, it was no longer tacky and looked …
-
- 0 replies
- 3.1k views
-
-
Hi, I've made some research on it and it seems to be ok, but just wanted to be sure. I made myself a cajon drum, and maked it out of pine (just a test piece, the real final cajon woulb be out of some other and hard wood) and just wanted to finish it with many coats of linseed oil, but after that I want to put some coats of lacquer for the piece to resist some abuse and have a glossy finish. Well, if you can confirm there is no issues with this procedure, I'd be on it! PS: other question, I am from Chile, so some woodworking finishes I can't seems to find in my language so I can buy them. Linseed oil is translated easily to "Aceite de linaza" and that's how I ge…
-
- 3 replies
- 8.7k views
-
-
I'm working on a jewelry box and am having troubles deciding what finish I should use on it. I is made of curly maple and walnut. So obviously the part I want to "show off" is the curly maple top and drawer fronts. For lack of a better term, what do you think is a "heirloom" finish for a project like this? The ones I've thought about so far are BLO, GF top coat, Watco Danish Oil, Shellac, and a water based poly. (If a photo helps inspire or opinion-ate, I'll be working on that next.) Thanks, Jerry S
-
- 7 replies
- 14.1k views
-
-
I'm making a coffee table out of red oak. I'm looking for ideas on how to finish it. I did a search and a finish I saw I liked was Danish Oil...I think that's what it was called. I'm new to wood working and not very sure about this stuff. What I'm looking to do is bring out the wood without adding any extra color to it so no stains or anything. Any advice would be great. Also, after I have my finish, can I put flat poly on it without changing the look too much? I want to protect it from feet and spilled drinks. Thanks!
-
-
- 7 replies
- 18.9k views
-
-
Hi, I just built an L shaped computer desk out of red oak. I wanted to put danish oil on it as I am really fond of keeping as much of the natural color of the wood as possible. I went with the golden oak shade, and after a day or so i added a coat of medium walnut (after my girlfriend suggested it). The color is beautiful and I am waiting for it to completely dry before finishing everything with satin polyurethane. My problem (this is my first project) is that I applied the danish oil on all the parts of the apron BEFORE gluing them to the top. They all have doweling holes corresponding to holes in the top, as I thought it would add strength to the join. As soon as I was…
-
- 6 replies
- 7.2k views
-
-
I am putting several coats of 100% real tung oil from the milk paint company on a walnut table top. After 4 coats the material does not seem to be soaking any more up. Is it time to stop applying and just give it a light buffing. I have no experience with this stuff. The directions state 10 coats for table tops.
-
- 4 replies
- 4.8k views
-
-
Hey All! Just finishing up an entertainment center for a friend. He bought birch plywood for the cabinet cases and poplar for the face frames and raised panel doors. The original intent was to paint the entire unit white. But after seeing the pieces come together he thought it would look good stained in Red Mahogany. We warned him about the possible blotching and the way the green may come out funny here and there. As you can guess, after applying the stain to the doors, much of it looks like a walnut-ish color and he doesn't like it. He's thinking of going back to painting it white. He really wanted to have a RED mahogany effect. My question is how can we alter the colo…
-
- 4 replies
- 7.7k views
-
-
I understand the friction finish process while the piece is on the lathe. However, I have a few bowls I need to turn for family. I was thinking about the topcoats. I usually spray finish my bowls like a piece of furniture, off the lathe, water-based. My question to you is…have/do you use a sprayer, either an airbrush or say a small spray gun…hell, even a spray can of Shellac or solvent Lacquer (the spray bombs) to deliver finishes to the piece while still spinning in the lathe? Any reason why you wouldn’t try it? What say you? -Ace-
-
- 1 reply
- 3k views
-
-
Hi - First time poster here . I have a question on lacquers . I recently bought a hvlp spraygun and am itching to use it ! So i built a practice box out of Maple and dyed it with a water based dye (meduim brown ) . Now my question - I was on youtube and they say lacquer is the easiest finish to spray on , So i was wondering can i use any lacquer or do i have to get a certain kind ? Thanx D
-
- 8 replies
- 8.6k views
-
-
Hello everyone, I'm new to the community, so forgive me if there is already a thread on this topic; I looked and didn't find one, but doesn't mean it isn't there. About a year ago I started a mission bed. As I was a student at the time, the most economical wood for me to use was poplar. While it was fairly nice to work with in terms of machining and mortise/tenon joints, I ran into some blotching issues with the finish. I did multiple tests, perhaps dozens, varying different stains (oil/gel/water based) and seal coat combinations (minwax pre-condition, old masters stain control, a premixed shellac). The course of action I decided on was the old masters stain contro…
-
- 0 replies
- 3.2k views
-
-
Constructing a canning / honey-processing cabin of stacked rough-sawn SYP 4x6 timbers for wife. During the nearly two years of stacking walls, building roof substructure and closing gables, it had developed a good case of the "blues". Got it now dried-in now and walls pressure washed & bleached inside and out, so want to seal the walls before doing floors. Question is about sealant choice: thinned poly via sprayer vs. something like Flood Clear Wood Finish (oil base) with garden sprayer (have done the latter multiple times in the past on a ceader board & batten house). Figure will need to repeat every few years regardless of product. All thoughts / suggestions abo…
-
- 1 reply
- 4.1k views
-
-
I am building a toy box out of purple heart. I am looking for a finish that will bring out the natural color of the wood and with stand the ware and of kids. I have never put a finish on ph before and any advice would be well appreciated.
-
- 3 replies
- 2.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·