Finishing
2,922 topics in this forum
-
Did anyone else start out with canned sprayed lacquer, or did you jump straight into using a gun? http://secondwindworkshop.blogspot.com/2012/09/keep-ball-rolling.html
-
- 3 replies
- 2.8k views
-
-
Hi all, I am a newbie to woodworking, so bear with my limited knowledge/terminology! I just acquired a lovely, large slab of redwood with natural edges and a hard shiny finish, which I think is probably shellac or something similar. (There are hard drips of the finishing material on the underside of the piece from when it was applied ) I would like to remove it or at least spruce it up a bit, but I dont want to ruin it. Ill try and post a pic. Any advice is appreciated!
-
- 1 reply
- 2.9k views
-
-
I'm using a spray system for the first time. Applying two coats of an oil based stain followed by a water based poly. My question is: do I need to Sand between all coats? I am going to apply the second stain today. Should I do a light sanding first ? If so, what grit? When i start applying the poly, do I need to sand between all coats? I figure it will take 4 or 5 coats of poly. Adam
-
- 3 replies
- 9.8k views
-
-
I have been asked to restore/refinish/clean up this table. I think it is from the 1920-30's it has a faux tiger oak finish on it. I am not sure what the base wood is perhaps poplar. I am not sure hat to do with this piece I do not know how to faux paint a new finish and I think striping it all off would not be good either and ideas. Thanks
-
- 8 replies
- 14.4k views
-
-
Hey Everyone, I have a table that had 1 coat of danish oil put on it 2 years ago. I would like to put a finish with better protection on it now. Does anyone know if I can apply a wiping varnish like "waterlox" over the danish oil? Or is there a better finish for a dining table? Thanks for the help!
-
- 5 replies
- 25.8k views
-
-
We had a tree taken down last year and I saved a slab and log that I thought would make a cool table for the back yard. It has been sitting in the garage for the last year and now it's just about ready for finishing...just in time for the fall. Anyway, I was looking for some ideas on what type of finish to put on it. I was thinking about just putting some water sealer, like Thompsons or something simillar, on it but if there's something that will poetect it and make the grain stand out better then a regular old water sealer I'd love some idead. The tree was a norweigen maple. Thanks
-
-
- 9 replies
- 3k views
-
-
I am still wanting to try this finish on a walnut top. I am unsure about a few things still: 1 Should I use polymerized tung oil? 2 Should I use 100% pure tung oil? 3 Should I use 100% pure tung oil blended 1:1 with citrus solvent? I am not really in a rush, and if it takes overnight for a single coat of undiluted tung oil to dry, so be it. It is important that the finish be food safe. Citrus solvent is almost as expensive as the tung oil. If it is only a drier, and makes the process only marginally easier, then I may skip it. If the solvent makes a difference in application (better performance means better results) then I am all for it! Anyone ca…
-
-
- 9 replies
- 6.2k views
-
-
Hey Guys, I've been thinking of getting into HVLP spray finishing and was wondering if anyone else was doing that and what they are using? As this would be my first system I'm looking for something simply that I can grow with. AndyL.
-
- 9 replies
- 3.2k views
-
-
Random question: Does the inclusion of gold leaf change or limit your options for finishing? The following pipe organ has an inscription that was carved and the gilt. I emailed the builder to ask about this process but figured I'd also open it up to the forum. Would a rub of linseed oil (or a spray of lacquer, or whatever...) ruin the effect or lustre of the gold leaf? Would you have to mask the letters off? Anyone have any experience with this? http://jaeckelorgans.com/index.php/organs Rice Lake, Wisconsin
-
- 2 replies
- 3k views
-
-
Does anyone get "Woodshop News", specifically have you read the article "Shellac overhyped as a sealer" by Bob Flexner. I don't have the depth of knowledge to question the article. I am just wondering if anyone has any opinions they would offer up after reading the article?
-
-
- 6 replies
- 3.1k views
-
-
I really don't enjoy finishing my projects. I usually end up with an average finish and doing damage control during the process. My cypress slab table looks great I'm looking to do a dark finish almost a deep chocolate finish. I have a test piece finished with minwax stain&poly 1 step. I really want to do a oil rub with a wax buff at the end. The cypress is really a light color with a dark detailed streak down the middle that I want to keep as its personality. Any ideas what kind of oil or any other finish you would recommend? The glass shop is making a top that will match the contoured slab so protecting the top should open up all options for any finis…
-
- 6 replies
- 3k views
-
-
Hello Can anyone give me tips on how to GLUE AND CLAMP this chair? Photo attached. It had to be disassembled and the joints are currently just tapped in. Given the angles of the legs (kind of A FRAME design) I don't see how normal (?) clamping will work. Many thanks Bill
-
-
- 2 replies
- 2.9k views
-
-
So...first I should say I'm still fairly new to woodworking, and a bit ignorant when it comes to making finishes. But I was wondering...has anyone ever used crayons to color wood in any fashion? Like actual, crayola style crayons? I was thinking for like kids toys, to get crazy colors. Would I need to "thin" it with some mineral oil or something? I tried searching for some pictures and sites, and didn't really find anything.
-
- 12 replies
- 11k views
-
-
I know it is a woodworking question. This is a little different, and you are just the people to ask. I have followed The Wood Whisperer since before the "Hot and Fresh Woodworking" days and this community is great! In addition to light woodworking, I've built a basic rolling desk, I am an avid older car enthusiast. That being said, I have a 1984 Mercedes Benz and it has quite a bit of wood for the center console and other trim in the dash. As with all wood and finishes the appearance has faded with time and cracked on the lower console and I would like to repair it. Here is the catch: It looks to be a paper thin laminate and the finish has a tint or color. …
-
-
- 8 replies
- 3k views
-
-
Morning. I have a problem with a 36"x48" maple butcher block countertop that has a few cracks and less then a 1/4' warp to it. I found this countertop workbench at an auction for $60. I bought it and loaded it up in the truck, which is when my grievous error occurred. I left the top in the back of my campershell for a day and it began to crack and warp. Yes I know better and I am kicking myself for the delay. Either way I brought it in the house and began to rehydrate it with a humidifier and a spray bottle which reduced the cracks by about half the size (less than 1/32"). The cracks are only on one side along the the upper portion (top) of the end and only partial in dep…
-
- 4 replies
- 11.8k views
-
-
Is there a finish i can put on a dinning room table that won't get the white water rings. It's a table made in china but looks like oak grain, has knots though. Has a finish on it is there a way i can figure out what kind of finish it is? The finish that's on it does get the white rings from water.
-
-
- 4 replies
- 3.4k views
-
-
I am working to complete a cypress box for the deck and I need advice on a finish. I live in Missouri so I need the box to withstand temperature extremes and humid weather. I have been thinking that maybe a marine finish will be the way to go. Are their other choices? Thanks for the help.
-
- 2 replies
- 3.9k views
-
-
I've just been finishing some drawer pulls with GF Enduro Var. Rather than get the HVLP out to spray them I went back to using foam brushes and then got that eternal problem with foaming. Anybody got any tips to prevent foaming when applying water based finish with these pesky pads?
-
-
- 1 reply
- 2.9k views
-
-
Hello, My mother has a table she purchased a few years ago that she is planning to refinish. The table is made from solid oak (I think) and it has decorative groves in it. Over the years the groves have become an annoyance because they catch food crumbs and other small particles. Is there a way to fill up the groves with a clear finish and seal in the entire tabletop without changing the way it looks? Any help would be appreciated. -Ron
-
- 7 replies
- 15.7k views
-
-
Looking for input on finishing of the jewellery box. Was thinking of shellac and a water based poly but have read that dark woods and water based poly can sometimes leave a bluish colour. Has anyone experienced this? Any other thoughts? Mike
-
- 4 replies
- 2.9k views
-
-
Does anyone have advice on how to not sand "cut" through edges when rubbing out. I have a chair I have been working on all summer and I sanded up to 220, stained and put 2 coats of shellac and then 5 coats of lacquer. Next I went with 600 to level the surface, all was fine, then I went to 1000 Abralon pads by hand and I was very conscious about stay away from the edges, however, on the small parts I still managed to cut through. Can I fix this without having to start over, there is not a whole lot, but it appeared in the most prominent places. Thanks Aaron
-
-
- 7 replies
- 3.5k views
-
-
Have you used this? Dish! My favorite water based "lacquer" product has just become a pain to get locally. I can get the GF product locally, so I'm thinking of switching. Of course, I'm planning to shoot some test panels. I have a 4 stage HVLP, so equipment is not an issue. Any thoughts and opinions are welcome on Enduro. Thanks!
-
- 13 replies
- 14.6k views
-
-
Hello, All, I'm new to the forum and figured you guys would be able to point me the right direction for this project. I make percussion mallets using bamboo as shafts. Natural bamboo(tonkin) with the enamel/skin still on is giving me lots of troubles when I'm trying to coat it with some sort of protective finish. Problem is that the skin is extremely non-porous and it's very challenging to get a finish to "stick" to it. I've tried oil based poly, GF enduro var, GF exterior 450, tru oil, tung oil, etc...all of them look very nice, but they can easily be scraped off with my finger nail. Most of these sticks take quite a beating being thrown in mallet cases and wha…
-
-
- 6 replies
- 17.2k views
-
-
I'm going to experiment with producing a "Bleached White" finish on some White Oak. Here's an example: http://bddw.com/furniture/table/mason_side2.html Anyone have experience/suggestions on the process steps to achieve this finish? Thanks. Cheers,
-
- 1 reply
- 3.3k views
-
-
Hi and thanks in advance for your help. My barn was finished in January and the Texas sun is already drying out the poplar siding. I'm almost finished sanding the pine T&G stalls and wanted to do all the wood finish work at once. I know how to paint by brush, roller or sprayer, but I know absolutely nothing about finishing wood. And, I've heard horror stories about what the TX sun does to wood (new to the state). I would really appreciate some advise on how to finish both the exterior poplar and the pine T&G in the stalls. I don't care how much time, how many coats, how many different products I use on this first time but my goal is to do as little mainte…
-
- 5 replies
- 8.6k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·