Finishing
2,922 topics in this forum
-
Hi I'm looking for a green alternative to polyurethane for the longboards that I'm working on... Any tips? I looked at the different kinds of eco resins and I also found this polyureseal? AFM Safecoat Polyureseal BP... http://www.amazon.com/AFM-Safecoat-Polyureseal-BP-Gallon/dp/B007C4XW1Q/ref=sr_1_3?ie=UTF8&qid=1360390557&sr=8-3&keywords=Polyureseal+BP
-
- 1 reply
- 3.6k views
-
-
Hello all, A few months ago, I installed butcher block countertops (beech from Ikea) in my kitchen. I chose Waterlox Original to finish them based on some Internet research and advice from a couple people at Woodcraft. I'm really happy with that product, but as it was my first time using a varnish, of course there are a couple (user generated) problems: 1. A small section of orange peel-ish texture in the top coat, I assume due to an earlier coat not drying fully before the next one went on. 2. A deep scratch from a screw in the rubber foot of my knife block. I believe this scratch may have gone through to the bare wood. I have heard that Waterlox is fairly forgiv…
-
-
- 4 replies
- 6.4k views
-
-
i feel like i should know this, and i would normally reference Marc's book, but i left it at the office. so i have a project that i stained with some minwax cherry stain. now i need to put a varnish on for protection. can i use a wiping varnish lightly thinned with mineral spirits over the stain, or will it cause the stain to smear/run? if necessary, i can get a spray on poly. i don't have an HVLP, so i'd have to settle for something in a can.
-
-
- 5 replies
- 22k views
-
-
Hi - I just bought a table at this store at a discount since it was slightly imperfect http://www.organicmodernism.com/index.php?p=62 I love the table BUT it's been less than a week and I can actually hear and see the table cracking (it wasn't cracked at all when I got it). I'd like to keep it - Is there any way that I can stop the cracking? It isn't in danger of cracking in half - but the top of the table is cracking across the entire table in a couple of spots. They mentioned beeswax and lemon oil for this. I love the look of the table (natural finish) as is and would like to treat it without making it shiny or darker. Any suggestions would b…
-
-
- 11 replies
- 3.5k views
-
-
So I'm building an walnut table with some Birdseye maple butterfly keys inlaid in it and I used some west epoxy mixed with dark walnut to attach them but the dye in the epoxy soaked into the end grain of the butterfly keys and gave lots of little streaks in them. Is there a way to use acetone or some other solvent to wash the dye streaks out of the maple?
-
-
- 6 replies
- 4k views
-
-
im looking for a strong durable finish. im making some small carving that are painted and in a couple spots the paint has started to chip from wear and tear. so i need a coating that will seal and protect the surface. i was thinking of mixing 2 part resin and diping them in the resin and then hanging them to dry. or maybe some kind of epoxy finish if they make any that go on thin enough to stay even and not be all goopy. does anyone know of a durable finish poly is not working, shellack is not thick enough,
-
- 10 replies
- 3.1k views
-
-
My house was built approx. 1940. Originally it had the old mortise locks on the interior doors, but was "modernized" along the way. They did a really bad job, using a jigsaw to enlarge the holes for the new style door hardware. I am restoring it back to the original style. I purchased mortise locks that fit into the existing holes (they never filled them), and I bought beautiful glass knobs and solid brass back plates from that era. Everything fits great. My question is how do I restore the doors. The plates are small and they do not cover the enormous holes. I have a couple of questions. One is how do I find the correct wood, and is that crucial. Second, can I use 2 siz…
-
-
- 7 replies
- 6.5k views
-
-
Hello, so I used Rustoleum Gloss paint and received a nice glossy finish. Stupid enough I afterwards applied General Finishes Salad Bowl Finish on top! (Knowing that it couldnt really penetrate the wood as it already had the paint on it, I still hoped it would equal out a few inconsistencies and figuered it wouldnt hurt.) Now the glossy look is all gone and I could kick myself. Apart from doing that, what can I do to get it back? Any ways other than sanding it down and taping it off and repaint? Its a pain as this piece is completly surrounded by natural looking wood (which I planed to seal with the Salad Bowl finish). Please help! Any ideas welcome! Thanks
-
-
- 5 replies
- 2.9k views
-
-
I've recently built a tv cabinet and I am now to the point where I need to finish it. Since this is a large piece of furniture I figured it lends itself nicely to spray finishing. I do not own a HVLP spray gun, but I have read a lot of good reviews about one from Harbor Freight, which is right down the street from my house. Anyway, I want to spray the stain on this thing. Do I need to thin it first? The stain itself seems fairly thin already, so this may not be an issue. Can I use the gun to spray poly over the stain? Do I need to thin it with something? I really have no idea what I am doing, so any advice is appreciated.
-
-
- 13 replies
- 3.8k views
-
-
This is the first time I have worked with a burl and live edge, could someone help me with the process? Especially with filling voids, how do you finish the live edge and the best finish to make the burl top really stand out. Thanks Rick Hammans Berthoud, Colorado
-
- 4 replies
- 5.7k views
-
-
Hello- I'm trying to fix a small crack on a conga drum of mine. It was submerged in water and developed a crack that runs perpendicular to the wood grain. It isn't deep at all. I've searched for information on how to fix it, but I can't find anything. The crack is about 1.25" long, on the curve of the drums belly, and on the other side of the wood are scoring lines that the builder put in.The drum is made of quartersawn oak. I was thinking about lightly sanding the crack out, but I'm a little worried that the wood will be too thin as the crack runs along the scoring. I've attached a photo. Thanks for any help!
-
- 9 replies
- 3k views
-
-
I will be completing a chimney cupboard style cabinet soon. It will be used for clothes in our bedroom. It is built with cherry, both plywood and solid. I am looking for advice on what type of finish to use. I have sampled tung oil, wipe on poly, watco oil,and an oil varnish blend. Still unsure what route I want to go. I probably am leaning towards wipe on or an oil varnish blend. I like a light satin finish. I thought this decision would be easier. I consider myself a novice and would appreciate any advice you can give. Thanks, Rick
-
-
- 14 replies
- 10k views
-
-
Can I apply arm r seal over general finishes water based enduro pre cat urethane? I would be wiping on the arm r seal with a cloth over a hvlp sprayed pre cat urethane. Would there be any adhesion issues or any other problems with this approach?
-
- 9 replies
- 3.5k views
-
-
-
This is just an example and not what I am actually doing. Say I have two boards of red oak. One I want to dye green and the other a yellow. They are then going to be finished with a topcoat. They are to be joined side by side. Whats the process for doing something like this? Dye first then join? Problem I would have with this method is I almost always never get a perfect join and require sanding or using a handplane to get a compeley smooth surface. Join then mask off and finish? Problem I have with this is Red oak is pretty porous and I see no way to prevent the dye from seeping under the tape so there isn't a sharp line and it might be a fuzzy blue strip …
-
- 2 replies
- 2.9k views
-
-
Hello, I am currently building a rocking horse for my little daughter. I chose to use Baltic birch plywood and had to discover that with the simple saw I was using some splitters when going against the grain were inevitable. I managed to do it quite nicely but would now want to protect the rocking horse from further being damaged (particularly splitters) when my girl rides it. (And I would like to protect my little one as well of course!) What finsh would you recommend? I do see all the postings for furniture and know a little about guitar finishes. But a moving rocking horse? I would like it to be 1) 'Kid'-healthy (when dried and in use) 2) Environmentally s…
-
-
- 3 replies
- 5k views
-
-
Hi everybody. This is my first post on this forum, although I go on it regularly. Anyway, I just finished building a honduran mahogany coffee table and I wanted to use an aniline dye to give it a different nuance and a little more character. Now, since honduran mahogany is pretty expensive, I did my homework on the exact measurement I needed and I am proud to say I got the exact boards I needed. However, there is a noticeable color variation between the boards. Here are a couple of pictures that show what I am talking about: and I guess my question is: Can I get away with using an aniline dye to bring the panels to the same color or do I need to go with a s…
-
- 13 replies
- 6.7k views
-
-
Hello! Is it possible to mix spruce sap with some kind of hardener to create a hard glossy finnish? Best regards/ sweden
-
- 3 replies
- 3k views
-
-
I just wanted to share this little tip with all of you here. Every year after Christmas, the wrapping paper always gets discounted super cheap, sometimes around a dime to a quarter a roll. It's common sense, but I tend to buy these rolls and keep them in the shop (aka garage) to roll out anytime that I do finishing, painting, or spraying. They are super cheap and work fantasitically well. I found out just how well yesterday when I spilled some stain and it didn't even bleed through to my table. Whenever I am spray painting and don't make a mess of it, I just roll the paper right back up on the roll and save it for next time. I just wanted to share and hope this makes some…
-
- 11 replies
- 3.7k views
-
-
I accidentally deleted the previous post (I'm still new to this). Anyway I appreciate all the help and I see the advantages/disadvantages to both glue sizing and shellac. I had one other question If I apply a fairly heavy (say 1# cut or shellac) I understand this will inhibit absorption of the dye. But...can't I either 1. Use a heavier concentration of dye (I use transtint and water) or 2. Spray more coats until I get the color I like, assuming dye builds on the previous application (the more I spray the darker it becomes)? Lastly I mostly dye cherry and I do tend to get "wild" with the color. I get it to a deep dark rich red color. Again thanks to all. -Adam
-
- 7 replies
- 3.6k views
-
-
I need a small finish spray gun for small one off projects. I make mostly small projects like jewlery, boxes key chains, carvings ect.... Not happy with my brushing so I want to set up a small spray booth. So I need a spray gun that I can hold the finish needed for projects a few inches across. I know a large gun will spray tight and small but it also a potential for wasting finish both in the container or in overspray. Anyone got any advise I have no expirence with spray guns so I'm starting research now. Thinking spray paint brush about the right size
-
- 8 replies
- 3.4k views
-
-
I built a pine kitchen table about 4 years ago and finished with a few coats of poly that has not held up well. It is peeling and looks horrible. This is a kitchen table that is used by 3 kids, will get wet, dings, any advice for a finish as I am sanding down and refinishing. If poly is the answer, that is fine as I was early in my woodworking career when I built this and, if I remember correctly, could have rushed the process.
-
- 6 replies
- 3k views
-
-
This is the first project that I'm using Arm-r-seal on (and I love it!!!). I just finished applying the 6th or 7th (I lost count) coat on a red oak dining room table, and was thinking about giving it a coat of Fiddes wax as a final touch. Good or bad idea? If good, how long do you suppose I should let the last coat cure before waxing it? Thanks in advance!
-
- 6 replies
- 8.1k views
-
-
Hey guys, First post here. Have a English Cottage Style house built in 1927 here in New England. Looking to restore the old woodwork in my upstairs hallway/staircase. I think it's stained in a dark walnut, not sure what type of wood it is, and I would assume it has a shellac finish. It's in pretty good shape but is pretty dull, has paint splatters, and could use a good cleaning. Few questions. Anyone have a guess what type of wood it is? Would the finish most likely be shellac? Was that common in this period? What is the best way to clean it and maybe bring back some of its luster? Should I apply a new finish coat? Thanks guys! Really like the forum so far. Lo…
-
- 22 replies
- 14k views
-
-
Hi - I am in the process of refinishing a small maple coffee table I picked up at the Salvation Army. I removed the old finish, sanded it down, and am currently applying multiple coats of Minwax Gel Stain in Walnut because I want the wood to match other furnishing's in the room. After I get the desired color, what is a good option to finish the table top? Obviusoly needs to be durable and I do not want it to have much of a sheen at all. Should I LIGHTLY sand/steel wool the top before applying a finish. I can see some dust particles in the stain when I look at it from a certain angle. Will these get hidden once a finish is applied? Thanks guys
-
- 11 replies
- 3.5k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·