Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by Barrettmusicman1,

    Hello, I'm a piano rebuilder and we're looking for a new way to finish. Could you use the thirds rule with linseed oil, spirits, and shellac? Could you then rub this out to a nice satin finish? Thanks!

  2. I'm making a 2' x 8' vanity top out of hard maple. I sanded to 220, wet well to raise the grain, then sanded again with 220. I'm using General Finishes water-based stain which worked great on test boards. I applied as recommended using a foam brush. I put a liberal amount down and worked a 2' x 2' section keeping the leading edge wet. I then removed the excess with paper towels and moved to the next section. I worked as fast as I could but still got overlap marks. This stuff is pretty thick and likes to foam. My shop was about 60 and I turned all fans off when applying. What am I doing wrong? Would thinning it with water give longer working time or make it worse? I've ap…

      • Like
    • 25 replies
    • 12.6k views
  3. Started by rbbauer00,

    I am building the steamer trunk that Marc built for Duane in TWW episode 82. For the frame, I chose walnut stained with General Finishes Empire Red water-based dye stain and Arm-R-Seal topcoat. Ever wanting to challenge myself, I am also going to try to veneer my own panels for the first time. I bought some walnut burl veneer which looks awesome, but due to the price (and the fact that I ordered almost too small of a batch to complete the project) I don't want to sacrifice a lot of it to test pieces. I did one test and found out that this stuff soaks up stain worse than end grain - so dark in fact that it masks the burl altogether and looks awful. The panel doesn't ha…

    • 7 replies
    • 6k views
  4. Started by jake2000_04,

    Hi All, I recently purchased a home and decided to stain the cabinets. I took all hinges off of doors and framing, and stained away! I found the same butt hinges, but different color from the original which I figured would be easy to install. I've installed some doors with no problem, but I am running into problems when I have to put two cabinet doors side by side. Some are rubbing, not closing, or fitting correctly. Is there anyway to adjust these hinges: http://www.homedepot.com/p/Liberty-Self-Closing-Full-Overlay-Hinge-1-Pair-78557/202066905?N=ar4i#.UXYMXMqaRq0 Any suggestions or tricks which will allow me to make these cheap things work would be great!!! …

    • 7 replies
    • 3k views
  5. Started by duckkisser,

    i have a tiny bit of tulipe wood that i have been cuting into pendents. spent a hour last night sanding before i realized that i wasent trying to remove sanding marks. i didnt have to sand back to 100 grit 3-4 times to get rid of the marks. what i had is very fine currly figure in the wood that looked like scratches but when i looked at it under a magnifyer it is just solid wood. worst part is that it is across the lines that is created with the tulipe grain. anyone else every run into that problem? just wondering if im the only fool who has sanding till his fingers hurt for no reason. for those of you who dont know what it looks like it a cream color and the grai…

    • 0 replies
    • 3.2k views
  6. Started by Kranzpj,

    I'm making an activity table for our toddler. Any suggestions on a finish that will stand up to stray crayon marks, small straw cup spills, and eventually the pressing of pens and pencils? Also, I'm trying to adhere some Lego Duplo building plates to a piece of plywood. Any ideas on a method of attaching them in a way where they can be removed? Thanks

      • Like
    • 5 replies
    • 3.1k views
  7. Started by buckwilde,

    Hello, I'm a newbie and have been quite pleased with my first woodworking project, which was to build a farm table and benches. See the pic below. Well, everything has been going smoothly, I sanded the hell out of it, hit it with a coat of stain, lightly sanded and stained it again. I've been waiting for a few consecutive nice days now to seal it with a polyurethane sealer I got from home depot. Ahead of this final stage, I've been covering the table every night with a weather resistant tarp to avoid it getting wet before I hit it with the sealer - I live near the ocean and it's quite humid every night. Well sure enough, like a bozo, I forgot to cover the table …

      • Like
    • 9 replies
    • 7.3k views
  8. Started by bobwax,

    My first grandy is due in October and I am building him/her a crib. With my kids approval I have about 100bf of cherry as well as some cherry plywood for the panels and rails. I've been woodworking now for a couple of years and for obvious reasons this is the most important project. I have a nice set of plans from Wood Magazine and am ready to rock. My primary concern today is the finish. I have no way of knowing if the child will have any allergies and want it to be safe when he/she starts gumming the sides or slats. Of course, it would be nice to know that it will hold up well for any sibling that may join us down the road. I have an HVLP sprayer and would …

    • 1 reply
    • 2.8k views
  9. Started by estesbubba,

    General Finishes gets a lot of attention on here and for good reason. I've heard a lot of good things about Target Coatings and was wondering if many on here use them? I recently got an Earlex 5500 and sprayed some test boards of GF Enduro-var and like it but also want to try some others as I experiment with waterbornes. Being a Waterlox user, it seems the EC2000 or EC8000 might give the closest results in look. I realized no waterbornes will be as dark as Waterlox but looking for a finish that gives the clarity and depth of it. Anyone have experience with EC2000 or EC8000 and what is the difference between them?

      • Like
    • 21 replies
    • 17.5k views
  10. Started by atcdav,

    Wood material is maple and the stain is Old Masters, oil based wiping stain. I sanded with100 and 180 but the milling cut lines are showing on the moulding,(perpendicular lines to the grain throughout the crown moulding). I didnt notice them until the stain went on. I obviously did a poor sand job. I also sealed with a 1# cut of zinsser sealcoat but still have blotching, was my coat of sealer too thin? not enough drying time? dried 1 hour. I looks terrible. I am going for a much dark color than I have, I know from my test boards a 2nd coat of stain will help with the color but what do I do? Sand it down and start over? The top is veneered plywood. it also blotched pretty …

    • 8 replies
    • 5.4k views
  11. Started by duckkisser,

    i need a stand that i can use for finishing. i make most small stuff so i need a counter top stand that can hold anything up to bowls down to small pendents. i want to rotate it that is the easy part just get a lazy susan but what would be a good way to hold the stuff up off a surface for spray finish? i came across this but it is kind of limiting to iteams with a stand that can be held in clothes pin to larger stuff i need a way to hold my project up on small pints but they have to able to be very close togther. and it has to flexible enought to deal with anumber of sizes of projects that i like to build. http://www.woodmagazine.com/woodworking-plans/shop-organiz…

    • 6 replies
    • 2.9k views
  12. Started by Evan Hargrave,

    I am refinishing some pews for my church they were painted and I have them stripped and they are in really rough shape. They have a lot if nicks and bangs and ALOT of hammer marks from repairs and things. They are worse than I initially thought. But the church wanted to stain them and let some of that old charm show. But, with all the repairs that have been done and the ones I will have to do I'm worried about how staining is going to look. I had a thought to do a darker tint to bring out some of the wear and then sand and do a lighter color over all. Any thoughts or tips. There's a lot of holes that I will need to fill with wood filler and I don't want them to stand out …

    • 6 replies
    • 5.8k views
  13. Started by mmisko,

    Hello-am new to this site and new to painting and finishing. I am planning to Spray paint Melamine Kitchen cabinets and have read various articles on painting Melamine-no two are the same. If i use XIM 400 primer what kind of paint and top coat do i need to use (if a good primer base is laid down, can any type paint be used?) or do they have to be compatible with Melamine ? Thanks in advance

    • 7 replies
    • 3k views
  14. Started by Eric.,

    I'm an unfortunate non-HVLP owner. I've been wanting to buy a Fuji or Earlex turbine for a while, but other tools always seem to take priority and I continue to wipe on my finishes. A friend of mine's brother is in the auto body industry, and he gave me this HVLP gun that was just sitting around. Brand new, but I know nothing about it...or HVLP in general. Could be top of the line, could be complete junk. It's made in USA, so maybe it's not bad? I'm wondering if anyone can tell me about the gun and if there's any way I can use it. The guy who gave it to me said I need at least 13cfm to use it, but my compressor is only rated at 8.6cfm...however, the front of …

      • Like
    • 17 replies
    • 6.1k views
  15. Started by cornballbub,

    Hi, Your site is very cool... I check it every now and then and build a board for a neighbor or friend. (hey that may rhyme) Maybe someone can help me with this dilemma; A friend can't decide on the finish for a maple cutting board, salad bowl or mineral oil?...which can I use and apply first, but still be able to remove (or go right over or sand or...) with the other if I decide? (choosy neighbor) Thanks CB

      • Like
    • 39 replies
    • 27.8k views
  16. I made a mahogany table top for a million dollar yacht. It's 38" X 48" X 1 3/4" thick out of one slab of wood. It's beautiful! It is going on the rear cockpit of the boat, so it will see some sun on the weekends, but I'm sure she will put a cover on it during the week. What's the best finish to use on something like this? It would be nice if the table was worth as much as the boat when I'm done :-)

    • 11 replies
    • 3.2k views
  17. Basically, my wife does hair and nails from the house in her spare time, but the table she uses to do nails is a little low and she has been having a sore back and shoulders from crouching over. She does a lot of hand painted designs and I would like to actually put her samples into an epoxy finish in the table top. But I am really worried about what acetone would do to an epoxy finish. I am sure acetone eats through just about anything, but I am wondering if there is a way to do this that will stand up to the abuse she will put it through. I did a little research and it looks like acetone is used to thin epoxy, so I doubt it will work. But I am still wondering if there i…

  18. Started by alancrist,

    I make landing nets and don't have a lot of experience with different finishing techniques. I have used polyurethane and spar urethane mostly. I think the spar urethane has better UV protection, and flexibility, but it yellows the wood more than I like. It is also hard to apply without drips and brush marks. I was wondering if anyone has any tips on good finishing techniques and products (or concoctions) for finishing landing nets. When in use, they don't stay wet a long time, but need some water resistance, of course, probably more UV protection than anything and flexibility. I was also wondering if I can put some sort of wax over spar urethane to kind of buff it a…

      • Like
    • 12 replies
    • 14.9k views
  19. Hello all, First time posting here... I just came across 11 "Series 7" chairs from the Danish furniture manufacturer Fritz Hansen. They are laminated veneer chairs. They were manufactured in 60's and 70's and they're just great looking chairs. Here's what they SHOULD look like: However, ours were hastily spray-painted baby blue years ago and then left in storage. The original colors and finish can be see on the underside of each chair where the spray paint didn't reach. I'm wondering the best way to attempt to restore these chairs. The original grain and color of the chairs is beautiful, and I don't see how sanding them down would give me a good resul…

    • 6 replies
    • 3k views
  20. Started by jmaichel,

    I would like to use a water based topcoat on top of GF blaze glaze but and want to just pick one up from Home Depot. Any recommendations? I would go with GF Enduro-Var but I would have to order it and I don't want to wait for delivery and I need to get these bookcases out of my shop. They are taking up some serious space!

    • 14 replies
    • 3.5k views
  21. Started by jbs550,

    I am building a pub table for a friend that is going to have bottle caps set into the top. Looking at doing a fill with epoxy and wanted to pick your brains to see if anyone had a suggestion for a good one to use. attached a picture of the top.

      • Like
    • 18 replies
    • 5.3k views
  22. Started by taksi,

    Hi everyone. New Here. I just took on a project of finishing some cigar boxes tha I had purchased for my groomsmen and I have only 2 days to finish. I started off by staining them with Cabot red mahogany woodstain and wanted to put a topcoat of some type on BUT... ...As some projects go, I didn't get the time to do the research on what type of topcoat I wanted to put on so my questions to you are? Is there a quick drying topcoat (varnish, shellac, etc) that I can use that will still look decent? Would something like BLO, danish oil or something suffice? I attached a picture that I hope you can use to help me out Thanks!

    • 9 replies
    • 2.9k views
  23. Started by alancrist,

    I am working out my preferred finish technique with the landing nets I build and have gotten some great ideas from this forum. On my most recent net I decided to use Formby's tung oil finish product. I really like the way it handles and looks because I like being able to rub it on with a rag and not leave brush marks. I don't mind taking the time to do a LOT of coats. I would like to rub on all my coats so as to avoid brush marks, but I also want some UV protection and Formby's does not offer that. So, I decided to add about a 1/2 a teaspoon of spar urethane to about a quarter cup of Formby's tung oil finish to do some additional coats. Has anyone tried this? If so…

    • 3 replies
    • 3k views
  24. My sister in law recently purchased an antique jam and pickle cabinet. It's made of maple and the door is tongue and groove about 3/4" thick face screwed into two cross pieces fo maple on the back. Would it be best to disassemble the door panel and run the boards through a jointer? Remove the cross pieces and clamp it flat with cauls? As always, any advice is greatly appreciated.

    • 7 replies
    • 10.4k views
  25. Hi. I'm looking for finishing ideas for a "cutting-board style" corner-desk top. For the handful of wood items I've made so far - I'm somewhat new to woodworking - my usual finishing regimen has consisted of Watco Danish oil, usually in "natural" color, followed by three or more coats of Minwax satin wipe-on poly, which goes on smoothly and streak-free relative to other polyurethanes I've tried. I'll probably stick with a similar plan for this desktop, but would like to bounce some ideas off y'all. Does anyone know if different Watco Danish oils can be mixed prior to application? I may want to darken the piece more, but just slightly more, than it would darken with "nat…

      • Like
    • 8 replies
    • 3.1k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.