Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

Finishing

  1. Started by mlehikoinen,

    So, I've recently done 1 refinish where the customer asked me to paint something white. It was a basic dresser and it turned out okay, but the paint was a pain in the -ahem-! It was too thick even after thinning and reaching a suitable viscocity where it was still causing some spattering. Of course, it was a water based latex. Is oil based latex paint thinner out of the can? Should I actually be using a different type of paint altogether? Reason I'm asking is that I have another request to white paint a dresser. This time it's a queen Anne style dresser which appears to be in great condition (shrug). Thoughts? I have an Earlex 5500 and I was using the 2.0 mm nozz…

    • 20 replies
    • 37.1k views
  2. Started by spwelton,

    So I've always had an affinity for old scientific type instruments and picked up a barometer at a yard sale, with the intent to make it look nice again. I got it all taken apart today, and I can handle fixing the brass bits and such, but wood is a new medium for me. My question for you experts is: The wood has a light brownish film on parts of it. See the picture linked below. So far, I've tried cleaning with mild cleaners such as murphy's but have had limited luck. Do you have advice on how I might clean it? Or do I need to strip it and start over? Thanks much! Sean

  3. Started by Driftwood Dani,

    Hi. I stumbled across this site searching for information about how to achieve the look I want for my custom maple kitchen cabinets that I just ordered the wood for. My cabinet maker is unfamiliar with how to counteract the natural pink tones in Maple without painting or going with a dark stain. I would like to know how I can get a light natural off white or pale moss green shade that doesn't hide the grain. Just a hint of color is fine. I'm not sure if it's called pickling or whitewashing but from the can of worms I've been looking it it involves a mind blowing combination of the following: thinner, primer, tinting, staining, toning, conditioners, gels, lacquers, etc. Ho…

    • 13 replies
    • 4.7k views
  4. Started by tdfster,

    My wife and I bought an older house last year and as we were doing remodeling I noticed that the studs in the walls were oak. Since we were removing several portions of the walls, I saved as many of the studs as I could. I am now in the middle of making them into a dining table table-top. I've started the process of joining and gluing up the table top and am working on finalizing my design in sketchup. It will be a trestle style table, similar in look to the table shown here (minute 4:22): will open with equalizer slides to hold 4 leaves, which I am planning to store under the table top between the slides. (as an aside, will standard soft-maple equalizer slides …

    • 6 replies
    • 6.7k views
  5. Hello folks, I have a Rosewood table that was in a sunny room with a runner down the center. After many years the area where the runner was is much darker than the rest of the table, appearing to be unbleached. I am wanting to get the table back to what the wood was like under the runner but am unsure as how to proceed. Initially, my thoughts are to strip the finish and sand till the wood is uniform. I was told the top is solid but I cannot confirm. I have attached a picture. What would you recommend? I find it strange that the wood would lighten with sun rather than darken like cherry and other woods do. I also wonder if the table reacted to the runner somehow and it…

    • 6 replies
    • 13.6k views
  6. Started by paul42,

    I have built a cottonwood table and want a durable finish but want to leave the color white. All the finishes which seem to claim they are clear still turn the wood yellow. Any experience with a white wood and a durable finish? Thanks!

      • Like
    • 10 replies
    • 8.2k views
  7. Started by Mike Brown,

    Has anyone had any experience with Franmar Soy paint stripper? I have read that it is relatively non toxic and doesn’t smell bad. I need to strip a set of Newel post and stair balusters. Since these are inside my house both qualities are important. This product is sold at Rockler or woodcraft, and it is not cheap, so I was hoping that someone might have some experience with it, good or bad. Thanks in advance for any insight that you can offer.

  8. Pretty sure this is okay, but thought I would ask. I have three coats of satin Minwax polycrylic on a project, and have run out. I have a full can of semi gloss min wax polycrylic. If I scuff up the surface with some 220, can I apply the semi on top of the satin?

      • Like
    • 12 replies
    • 16.7k views
  9. I am at the point of applying water based poly to a bookcase. Probably go for 5 coats. Since I will be able to apply two coats per day, is it OK to leave whatever poly is left over between coats in the spray gun cup and then Clean it out after the 2nd coat of the day? Adam

      • Like
    • 24 replies
    • 4.9k views
  10. Started by angelok,

    I've made some built-ins for my kid's new bedrooms (<1 yr and 4 yrs old). I love the finish of a sprayed on oil-based paint... it just looks so perfect on woodwork. But, like every good dad, I'm concerned about protecting the little ones. VOCs have gotten a lot of attention recently, and I wonder are there any viable alternatives to oil-based finishes that give me a better-than-latex look that are safer than oil? Alternatively, my kids aren't in these rooms now... and waiting another month won't change anything in the scheme of things... would waiting it out make a difference? Thanks for any insight.

      • Like
    • 11 replies
    • 11.1k views
  11. Started by Eric.,

    I just got back from Rockler and I was talking to a guy about TransTint. He swore you could add it to Arm-R-Seal. I didn't think that made any sense because TransTint is water or alcohol soluble, and Arm-R-Seal is an oil-based urethane...so I'm assuming it's diluted with mineral spirits or some other petroleum-based solvent? I'm wanting to dye, stain or tone some mahogany on a project I'm about to start, then topcoat with Arm-R-Seal...it would be great if I could just use the TransTint in the varnish to eliminate a step, but I think this guy might be confused...I thought you could only add TransTint to alcohol or water-based stains or topcoats? Thoughts?

      • Like
    • 10 replies
    • 7.6k views
  12. Started by dwacker,

    My daughter called me steaming mad. Last week I sprayed some finish samples and she picked the one she liked. My poor son in law had to spray their brand new fireplace surround cabinetry. I put the finish formula on the back of her sample and off she went. I walked in and the off black finish was blinding with the sun from the window. My poor son in law with his tail between his legs just sat there and took the tongue lashing. As she proceeds to tell me SHE mixed the finish and I screwed up the formula and her husband must have sprayed it wrong. Calmly without taking my 30 year old brat over my knee, I asked for a cup of untinted finish to see what went wrong. Sure e…

      • Like
    • 8 replies
    • 2.9k views
  13. Started by Dan Hecox,

    I'm building a coffee table and end tables out of weathered oak. I sanded, vacuumed the project off and wiped it down with tack cloth. Now the stain I used was Minwax, oil based stain, natural finish. After staining and wiping the project down, an hour later the stain was like bleeding out of the pores of the wood. And it continued to do this for 48 hours after staining. I continued to try and buff these bleeding areas. But in a few spots where it bled out, the stain dried and it can't be buffed or wiped off. Any thoughts or ideas on why this happened? And what to maybe do about it? Any help would be much appreciated. I'll be using SW pre-cat lacquer. Sincerely…

      • Like
    • 2 replies
    • 4k views
  14. Started by rickheel,

    I have a bed I need to repair. The headboard is attached to the side rail by a bed bolt with a half moon. The wood inside the headboard has cracked a bit under the washer and I am concerned about tightening the bolt more due to potential splitting of the wood. The washer is somewhat bent. I am wondering what my best course of action would be. I thought about using an epoxy to fill the area(after inserting a sleeve to keep the hole for the bolt open) or maybe drilling down a bit and inserting a wooden dowel and drilling back thru from the side rail end. My expertise is at a low level and I would rather go the epoxy route but I am concerned about the strength of the epoxy i…

      • Like
    • 14 replies
    • 4.1k views
  15. Started by atcdav,

    I am using oil based stain and when I apply a second coat it is reactivating the first coat. Can I layer seal coat (50/50 alcohol) inbetween stain layers? Do I need to just allow more drying time? Is there an issue with using the seal coat on the bare wood and the again after the stain before the top coat?

    • 11 replies
    • 15.1k views
  16. I'm trying to fix a small section of table top where veneer chipped off. I tried using an oversized section of veneer taped over damaged area. I taped it over the area and cut out a patch with a very sharp razor knife. I glued and clamped patch into area. After dry I lightly sanded and stained. The edges of the patch are very noticeable where it crosses grain. I cut a very tight patch but still couldn't hide it. So I tried sanding a little more and went through the veneer. Any tip on how to fix this would be great. What's the trick to this?

    • 5 replies
    • 2.9k views
  17. Hello! My husband and I are refinishing some vintage dressers and we want them to have a smooth high gloss finish. The dresser we are currently working on has deep grain and we aren't sure of the best way to fill it. We are using Sherwin-Williams Vinyl Primer Surfacer and High gloss white Hi-Bild Precat Lacquer, spraying with an HVLP gun. What is the best way to fill the grain? Thanks, Kirsten J.

      • Like
    • 7 replies
    • 6.9k views
  18. i'm in the process of making a carved sign for the front of my workshop. The sign is made from 2 old pine boards i found in abandoned farmhouse a few years back, they must be almost 80 years old... I would like to give the signs a finish that makes them look old and aged but not being too dark, as the carved lettering will be painted black. I would like the board colour to remain quite light brownish, but still have a finish that will make the wood pop out and highlight the "scars" it has on it. I though of using the vinegar and steel wool, but every example i have seen turns the wood too dark. Any suggestions?

    • 6 replies
    • 2.7k views
  19. Hi, thanks for looking at this post, to start with, i am a complete amateur/novice/ newcomer to woodwork; Im a leadworker by trade so i have no idea how to go about restoring this cabinet to its former glory Its a 50's style walnut (i think) cocktail cabinet. It has quite a bit of damage ranging from coffee cup stains to some chips in what looks like lacquer or varnish. i have a read a few posts around google recommending very fine steel wool and methylated spirits or denatured alcohol (for my americn cousins; its the same thing right? ) however after listening to Marc on comic dorks i figured this was the authority and place to visit to answer this question…

      • Like
    • 3 replies
    • 3k views
  20. Hi guys! New to the forum and woodworking in general. I started an estate clean out business and found that I really enjoy restoring the antique pieces I find. One such piece is this 1930s Drexel Dining table. It is a wood veneered top and in excellent condition with one exception- the table pad that was placed on top to protect the wood has actually caused it to wear unevenly. You can see that there are two wear marks that run down the length of the table, opposite the grain. What is the easiest way to remove these lines? I've tried a light detergent and washed the top, I've tried Old English and also Howards Feed-n-Wax conditioner, but the lines still come throug…

      • Like
    • 1 reply
    • 3.3k views
  21. Hi everyone I'm in the middle of refinishing and old Chiffon robe of my grandmother. I've sanded most of the finish off and noticed a couple of the drawers have cracks in them and I'd like to know how to repair them or just leave them alone. This is my first time doing something like this and I'd also like to know how I should proceed with finishing. What products are user friendly and are good. Something else just looking at the drawers can anybody tell what type wood this is. Thanks

    • 1 reply
    • 2.9k views
  22. Started by maly,

    Hi all, I am new in woodworking. I am doing now a custom bathroom vanity and I would like to know how to seal and stain it a matt finish and at the same time protect it from water damage. What I should use and how? Thanks

      • Like
    • 8 replies
    • 17.5k views
  23. Started by Tpt life,

    Admittedly not fine furniture: I was waxing the drawer guides in a dresser. The guide was a traditional wooden T guide and the drawers have an attached metal C channel. The grain orientation of the T guide means that sliding the drawer into the carcass causes the grain to raise and be caught by the C channel. I am not sure this will cause problems but a fly away tear could cause the drawer to bind. I have always gone for straight grained guides out of semi hard secondary woods like poplar. These figured oak guides in this piece clearly need attention to grain directionality for long term use. (To be clear I am not sure this production piece was intended to stand the test…

    • 0 replies
    • 2.9k views
  24. Started by JohnDi,

    Building a top with a curly maple field and a cherry border. Want to pop the grain on the maple. Already glued the cherry to the top so both will get dyed. Any suggestions for what color dye? The cherry has some figure as well so I'm thinking it will pick up dye as well. Was going to use transtint dyes like marc did in his video.

    • 9 replies
    • 4.6k views
  25. Started by CJC5151,

    Im spraying a waterbased product called Aqua coat table top semi gloss. And im having a real problem with bubbles forming in my finish...anyone have any idea how to combat this. Its 68 degrees in my shop and 35% hum. any help would be great

    • 6 replies
    • 5.3k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.