Finishing
2,922 topics in this forum
-
Now that Marc has me hooked on Arm-R-Seal, I need some advice on storing it properly. I bought a gallon and tranfer small quantities (1 cup or so) for use into a quart paint can. Problem is, it usually skims over before I have used it up. I looked into Bloxygen, but seems pricey too me. Any recommendations? Thanks.
-
-
- 13 replies
- 6.2k views
-
-
I am looking to start a new cabinet project that will be painted. Plywood is going to be used for the case work. I want a smooth finish but don't want to use mdf. What plywood have y'all had good luck with and what finishing technique did you use. Birch is my first guess but I didn't know if I can get a smooth finish like mdf. Any thoughts will be helpful. Thanks.
-
- 7 replies
- 3.5k views
-
-
Hey guys...looking for some help in the finishing department for this project. So, I have a basic 30" base cabinet, with solid oak facing and doors / drawer. I will be using cabinet grade red oak ply for the sides and back, and adding red oak posts on the four corners. Basically, I will be transforming this simple (read: cheap) base cabinet into a multi-purpose island in the kitchen. I've been playing with a few different approaches in regards to finishing. I want the finished base cabinet to be a warm, dark espresso color (almost like a dark walnut, but with more of a chocolate-like warmth). I found a stain, made by Rustoleum (yeah, I know, it's not a GF), called …
-
-
- 16 replies
- 8.4k views
-
-
I want to keep the gloss on 6 coats of Arm R Seal. There are some nibs on the surface so they have to be removed first. Can I rub out the final coat and what is the best way to do it?
-
- 5 replies
- 10.2k views
-
-
So after the bed finishing fiasco my wife asked me if there was a book that I could get to get more info on finishing. So I told her 'well there is this class that i want to go to up in VA, but its $475'. So then I told her 'well I have Marc's book, so what else do i need?'. To which she replied 'obviously more since you messed that one up pretty good'. Ouch. So I went on Amazon looking to get one of Flexner's books. So which one? I read the reviews on several and there were a lot of comments that most of the info was rehash from other sources (books/columns). I'd like to have a pretty comprehensive source, but one that someone who is still a beginner can make…
-
- 7 replies
- 6k views
-
-
Hey guys - I have been looking for a stained french door to replace my painted french door for awhile now. I have been trying to avoid just stripping my door and refinishing it because I feel like I won't be able to match the existing trim/patina that well. I found this door at a local architectural salvage place and it's the exact size I need, it just like a shade or two LIGHTER than what I need. http://www.noreast1.com/dr0265b.JPG Would it be possible to make this a little darker without having to refinish it completely?
-
- 1 reply
- 2.9k views
-
-
Just started using the Earlex sprayer with Target EM6000 lacquer. Practiced on maple ply shop cabinets and everything was fine. Nice smooth finish. Began working on a cherry bartop for a customer and got all kinds of orange peel in the finish. I sanded to 320 grit, one coat of de-waxed shellac, sanded, removed dust with vac and tack cloth and began to spray. Temperature was good. Sanded between coats but finish was not good. Did I spray to heavy a coat? Only difference between my practice and the cherry was I went from satin to semi-gloss laquer. Thanks, Rick
-
- 6 replies
- 7.7k views
-
-
Good day, Question.... I've just finished a new table top, 56 inch long by 40 inch wide. It's maple. Now when I glued it up, it was nice and flat... I made sure of that. Now what I did, was put a coat of water based finish on the bottom (only one coat) and then flipped the table top over and put a total of 4 coats of finish on... now the entire table has cupped... and alot!!! If I put on a strait edge, it's about 3/4 of an inch off.... am I ever happy!!!! My question is... is it because of the uneven amount of finish I put on... (I'm thinking maybe the wood absorbed enough finish to cause the cup), and my other question is... if I flip the table and put 3 coat…
-
-
- 18 replies
- 10.6k views
-
-
ive been searching for a good do-all type of kit and this seems like it fits the bill especially since they dropped the price in half.... its only $199 at Woodcraft.com right now.... any comments or concerns? do you own it?
-
- 5 replies
- 2.9k views
-
-
Preserving, Cleaning and Refinishing Teak For Indoor Use. We have some teak furniture we recently bought that is for indoor use - side board, coffee tables etc. The teak is solid teak and looks great for the most part. A larger Image: Teak Detail For the parts that look great they likely need a yearly coat of what ever one coats teak with. Would that be teak oil and what teak oil is recommended or would that be Tung Oil? I have read that teak oil can be really nice or some odd product that is questionable. I must have read 10 articles on dealing with teak but never quite felt satisfied. The other parts that do not look as great might need a cleaning a…
-
- 6 replies
- 33.5k views
-
-
I am a long time Waterlox user and absolutely love the product. It is easy to use and looks great. The only downside is the slow dry and cure times which can sometimes put off odors for weeks. It seems waterbornes are gaining more momentum lately and General Finishes and the Earlex 5500 are popular for hobbiests. I think if I'm going to dive into waterbornes that spraying makes the most sense. I do have some questions: 1. Can you spray inside a garage? If so do you just cover all your machinery? 2. What air temps do waterbornes need sprayed at? 3. My favorite mission finish is water-based dye, dewaxed shellac, oil-based stain as glaze, and Waterlox topcoats. Can…
-
- 2 replies
- 3.3k views
-
-
I know the Earlex 5000 system is a popular unit for us hobby woodworkers. I've had mine for about 4 years and have sprayed probably about 15 gallons of finish through it. Mostly waterbase but some shellac. Lately, I've noticed the motor having a different pitch and I think it sounds like the bearings are starting to go in the unit. Wondering if anyone else has had similar issues? Lucas
-
- 5 replies
- 3k views
-
-
My old solid walnut table just came back to me after several years of rather hostile territory use. The top was in sad shape when it left & now it is in very sad shape. In addition to many discolored splotches, etc. it now has a couple of places where the wood is beginning to split. I am a clueless grandma here & not in a position to consider trying to refinish at this time, but would like to do what can be done to safely clean up and help the surface, hopefully encouraging the cracks to tighten back up, in a non-toxic way since I am chemically sensitive. Is it as simple as using some kind of natural oil on it? Thoughts & ideas? Thanks much.
-
-
- 13 replies
- 12k views
-
-
So, my daughter came home from college on Christmas break and asked if i could help her build a toboggan. How could I resist.... Toboggan is fine, but our mineral oil and beeswax has remained very "tacky." First coat was 3 parts mineral oil and 1 part beeswax. That dried nicely in 24 hours. Second coat of 1 part each is still very tacky after a week. Any suggestions other than rubbing it down to remove any excess (maybe we put it on too heavy) and giving it more time to "cure"? As is I can't imagine it would slide down anything short of a cliff. Maybe it is safer that way....
-
- 9 replies
- 12.4k views
-
-
I'm new here and thought someone may be able to help me with a problem. I want to spray lacquer some old oak panel-in-frame cabinet doors. The gap between the frame and panel is larger than normal and will not fill wth paint (primer is on) and I need a filler that will allow some movement but be compatible with the lacquer finish. In my research I came across 'Lecol 7500' except that it doesn't seem to be available in Canada. I'm in Waterloo ON. Any suggestions?
-
- 3 replies
- 3k views
-
-
Hi Everyone This will be my first post on the woodtalk forum. I am going to restore my wooden garage doors ( Move into new house ), and need some advice on restoring my garage doors. The door is divided into 5 wooden panels, and the bottom 2 are almost black with neglect, I want to restore all the panels to pristine order. ( The back of the panels was never treated) The manufacturer said not to use varnish and only their oil products? Why can't I use varnish? Not even a good UV polyurethane varnish? Or is it just a sales gimmick? The door is exposed to harsh weather, very high humidity and the temp get well above 100F, with lots of rain in the summer. Any advice w…
-
- 5 replies
- 7.9k views
-
-
Hello all! First post here on the forum (and first foray into woodworking on my own; my used to do a lot and gifted me some tools), and I'm looking for advice on a finish to use for a small (2x2x1.75) engagement ring box I'm making for my future (hopefully!) fiancé. Pictures below. It's wenge and padauk, and I'm looking for a smooth, high-shine look, similar to a guitar finish. Was thinking a wipe-on poly or shellac. Never done this on my own before, so if I'm way off the mark, let me know! Thanks! Chris
-
- 10 replies
- 6.3k views
-
-
We recently purchased a pine roll top desk. It doesn't any finish on it at all. We know how to finish the main part of the desk but how do we finish the rolled part? We are only going to use polyurethane and keep it natural. How do we go about finishing the roll top portion? Thanks
-
- 1 reply
- 3.1k views
-
-
hi there doing a 55 piece cabinet job...maple...stripping existing urethane off (has old coat of honey stain on under urethane) customer chose dark brown and gave me spec to buy stain and do sample i stripped one door..took off urethane and sanded...left the old honey stain in tact. two applications of waterborn brown stain by brush...(no conditioner)....wiped off stain both times...brushed on 3 coats of latex clear satin varathane...showed customer sample....she loved it....therefore got the go ahead for 55 pieces. question: should i continue to *not* condition the remaining pieces?...sample piece not blotch...but almost...if that makes sense. question…
-
-
- 5 replies
- 2.8k views
-
-
can Arm-R-Seal be used over water based stain without a seal coat of de-waxed shellac between?
-
- 3 replies
- 2.9k views
-
-
Hey guys, quick question, but how long should it take for shellac flakes to dissolve? I'm not sure if I'm just being impatient or if my math was wrong and I made way to strong a cut. From what i could understand from the math it should be 1 oz per 1 cup of denatured alcohol for a 1lb cut. I used 3oz in 3 cups yesterday, been doing a little shaking of it, but it still hasn't fully dissolved. This is my first time using flakes rather than just getting some Zinser and thinning that and not sure if I did it wrong, if this is normal or what.
-
- 10 replies
- 3.6k views
-
-
I am building a bed that is a gift for a friend of ours. Her room decor is red/black so we decided to build out of pine and then paint it gloss black. I am using an Earlex 5500 and after talking to the guys at the local Sherwin Williams and explaining my project they recommend one of their oil-based enamels. I messed up initially by not priming, so the first coat ended up becomming $21 a quart primer (ouch!). After the second coat, the faces look like this but the end-grain looks good. I thinned the enamel about 5% and am using a 2.0mm tip to spray. Any ideas as to what may be going wrong or what I can change? Thanks in advance!
-
-
- 33 replies
- 17.5k views
-
-
I've never used an boiled linseed oil and wax finish and am looking to use it on my current project. I'm building a quilt rack that will clamp the quilt in between two boards. Since I haven't used it, I'm not sure if I should be worried about the oil/wax transferring to the quilt. This may not be an issue but thought I'd ask. I also thought about using BLO and then shellac or poly over top of it to seal it. Thoughts? Thanks, Justin
-
-
- 15 replies
- 9.9k views
-
-
I just bought my wife a cedar chest for a Christmas gift. I found one in pretty good condition and would like to give it to her next week. The chest is finished in cherry, and it looks very good, except for a few scuffs and light scratches. I'd like some suggestions on doing a quick and temporary touchup, just to maximize the appeal. Sometime in the next year I'll refinish it completely, but for now, I'd like to do something to help shine it up and minimize the scratches, something that won't be a hinderence when refinishing later and also that won't take me more than a few hours to do. I was orignally thinking about shellac or oil finish, but wanted to get some oth…
-
- 7 replies
- 6.4k views
-
-
Hello all, Over the New Years long weekend I finished installing all the exterior skin panels on the camper. Winter has set in, and it's too cold outside for fiberglass or body filler to cure properly, so I am going to start on the interior. This isn't the sequence I had planned, but in the end, you play the hand you are delt. For the interior I am using the scraps from cutting the exterior skin panels. It's 1/4" moisture resistant hardwood underlayment. It has one face that is light colored with a surprisingly pretty grain pattern to it. As a test I took a small scrap piece and rubbed on boiled linseed oil. I was very plesantly surprised at how good the grain looke…
-
- 0 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·