Finishing
2,922 topics in this forum
-
Im bored and wanna get some work done but i wasnt sure if i should apply a coat of Arm-R-Seal top coat while its raining outside i work in my garage shop.. not climate controlled... seems fine to me but i thought id ask and make sure... its about 60 degrees btw
-
- 4 replies
- 2.8k views
-
-
We have a dining table that has a solid wood top, I think pine. It has a dark finish. We bought it used from friends 3 years ago and it has always what seems to be to be this haze on the finish. I am hoping some basic steps can restore the finish, but don't know enough to try. It also has some light white stains from moisture/heat. I have attached some pics. Thank you. Dan
-
- 8 replies
- 3k views
-
-
http://www.rockler.com/m/product.cfm?page=10469&utm_source=NL&utm_medium=email&utm_campaign=V2328 $120.00 HVLP with Rockler on the side. I've been raised to think that if it sounds to good to be true, then it probably is. Thoughts? Experience with this system?
-
-
- 11 replies
- 6.2k views
- 1 follower
-
-
got a maybe rather odd queston. in my house i have a ~4' high half wall. it sorta seperates our laundry area. my cats like to jump on it to hang out on or use it to get to higher places. it's capped with a roughly 5" wide x 1" thick piece of solid wood (i think it's oak). lately my cat buddy has been having trouble sticking the landing and i wondered if i can help the poor little bugger out by making it a little less slippery. now i know there is safety floor paint to which you add aggregate to make the finish gritty and non-slip. is there something i can do along those lines but clear. i don't want it to be too conspicuous. thanks, Sash
-
- 2 replies
- 2.8k views
-
-
Hi, I am new to woodworking, so would appreciate some advice for the following. I made a wall shelf like the one in Amazon at http://www.amazon.com/Welland-Lexington-Espresso-Unfinished-Color/dp/B00A6D82HE/ref=sr_1_36?ie=UTF8&qid=1362029605&sr=8-36&keywords=espresso+wall+shelf. I used pine wood from http://www.menards.com/main/building-materials/lumber/construction-lumber/spruce-pine-fir-spf/1-x-4-x-6-select-pine-board/p-1934079-c-5689.htm Now, I need to get it finished in espresso cherry color similar to the color in the attached (it's just espresso) image. I am bit confused over what kind of finishing product to use. I see some as wood stains…
-
-
- 12 replies
- 9.7k views
-
-
Howdy All! I'm starting a project to do carriage door for my garage shop and looked back at the finish for done on video 46 - "Desert Outdoor Finish". It seems that method would work well, but wanted to see if, 5 years later, anyone had anything else to add or if this method still seemed to work well. Kind regards! Eric
-
- 2 replies
- 3k views
-
-
Evening, first post, new to fine woodworking. I've just successfully veneered my centre speaker with american black walnut, I'm very pleased with the results however I'm looking to darken the wood. Any suggestions? Many thanks in advance.
-
- 17 replies
- 8.6k views
-
-
Anyone care to lend their expertise about finishing pine patio furniture? I love the look of BLO on just about everything but I need a lot more protection for my new outdoor creations. They will be exposed to all the elements and I want to make sure they are well protected but still have the depth and character of a BLO finish. Thanks in advance. John
-
-
- 10 replies
- 16.6k views
-
-
Hello Wood Peeps, I am building a small vanity with pull out drawers for a bathroom. The majority of material used in construction is Teragren Bamboo panel (3/4"). Does anyone have a suggestion for finishing? I am worried about water and humidity. A satin finish is preferred. Thanks, Dennis
-
- 2 replies
- 2.9k views
-
-
-
I'm pretty new to woodworking and have been making my way through a simple Arts & Crafts style side table in a class at a local woodworking school. So far it's come out great - so I'd like not to screw it up now! It's all white oak, with the tabletop out of quartersawn with prominent ray flecks. The instructor was suggesting just a clear wiping varnish (a la TWW) since it's difficult to mess up. I would really like a more traditional looking mission/A&C finish though, something that will really show off the grain of the oak and the QS features. I have some spare QS boards that I can experiment on if I can find something that sounds reasonable. I've loo…
-
- 16 replies
- 15.5k views
-
-
I have a old Devilbiss spray gun MBC 510 that I use for finishing but I accidentally broke my fluid tip. Now I'm looking for a replacement. How here's the problem. I found a replacement tip but it's 1.4mm while my needle is 1.8mm. I need to know if I'll have any problems finishing when I use this gun. Or should I buy the tip and then find a matching needle? I have a #30 aircap if that matters too. I mostly spray lacquer and I really don't need such a large tip set.
-
- 3 replies
- 3k views
-
-
i am working on a chest of drawers and was wondering how it would work with a danish oil finish.... i like the idea of the product but have never used it and really dont know much about the finishing process to begin with so if you have any comments or concerns i would greatly appreciate your feedback
-
-
- 15 replies
- 8.2k views
-
-
I decided that I am going to use Boiled Linseed Oil on the bench I am building. I have not used any finish other than polyurethane so I am not familiar with all of the details with this application. I have done some research on it but I would just like to confirm what I have found. As for the preparation of the bench for finishing I am planning on sanding up to 220 grit, raising the grain, and sand again with 220 grit. Most of what I have read suggest sanding up to 320 grit but my thinking is that it is just a bench that will get scratched and dinged so going to the higher grit isn't necessary. Is this a fair assessment on my part? Now with the application of the…
-
-
- 4 replies
- 6k views
-
-
I have some quilted maple that had just stunning chatoyance when it came off the planer, but it seems to be less noticeable after sanding. I'm hoping a it comes back. I'm looking for suggestions on finishing it to get the maximum effect. I have a number of small scrap pieces which I will use for testing different finishes. I used Marc's method from "popping the grain" and used some transtint dye in shellac; used dye just diluted with DNA; and also more typical finishes - straight Arm-r-seal, some BLO, and a oil/varnish blend I had left over from a previous project. I don't have any lacquer to try. I am most interested in bring out the shimmering effect. Any other …
-
-
- 11 replies
- 14.6k views
-
-
I can't find Marc's video he did on spray can topcoats. I know I watched it a while back..... Anyone remember the title?
-
- 3 replies
- 2.8k views
-
-
Hey Guys, When I was a kid (about a hundred years ago) I spend 7 years working for a local paint company. I told everyone what the company told me to: Shellac is outdated. Boiled Linseed Oil is useless Lacquer can't be used for woodfinishing. Polyurathane is the be all and endall for woodfinishing. Low and behold, in my late 50's I started woodworking. I've used poly, BLO, tung oil for a variety of projects and they've done the job. I am now working on my "masterpiece". A bedroom set for my wife and I out of Ash and Walnut. I have started on the two nightstands and am not sure what would be the best finish. I have an HVLP sprayer, but an not married t…
-
- 4 replies
- 2.9k views
-
-
I posted this Fall that I had a bunch of red oak quartersawn and now I'm looking to start experimenting on finishing techniques to really make the fleck / grain POP! This lumber has some wicked character!!! From what I've come across fuming seems to give the best results (although maybe not the safest)... I work with chemicals on a daily basis and am equipped to manage this aspect BUT, I've never done this before (fuming).. I don't typically work with oak, but I have a lot of it and being QS there is a lot of character to highlight!! I grew up with regular sawn oak everywhere in the house (with the big cathedral grain lines) and it creeped me out as a child;…
-
- 11 replies
- 10.8k views
-
-
I purchased black walnut froma few different sources and half of teh walnut I got has a deep red hue that is drastically different from the rest of the walnut How do I reduc ethe red hue in the wlanut? Bleaching and then brown hue in an oil finish?
-
- 6 replies
- 11.7k views
-
-
As I near the finish line of my Roubo I am starting to think finish. I was planning on making my own Danish oil using Arm R Seal but living in Minnesota I am concerned about ordering due to freezing, then I got to thinking how do they ship to stores? Now I am leaning more towards just blo for now and this summer I will be in an area when I can buy the varnish. Anyone know how they deal with the shipping, I can't imagine that it isn't an issue.
-
- 3 replies
- 3k views
-
-
Hi Folks, So after a year of knocking down walls, wiring,plumbing, laying hardwoods and assembling my made in the USA cabinets from Barker Cabinets, it's time to paint the cabinets and I'm suffering from paralysis by analysis!. Dear wife wants me to get a painter in to spray them but I've done everything up to this point in this remodel and am determined to do spray the cabinets too Now I've never sprayed paint before.. The cabinets came sanded to 180 grit I bought a HVLP from Wagner http://www.amazon.com/Wagner-518080-Control-Spray-Sprayer/dp/B003PGQI48/ref=cm_rdp_product and have been practicing on some old doors with decent results. I've bought this fr…
-
-
- 11 replies
- 7.1k views
-
-
Hi I am refinishing an oak plywood stand for a saltwater fish tank. I built the tank a few years ago, and finished it with a water-based poly. Unfortunately, the finish didn't stand up too well to the occasional drips, spills, etc. After stripping the stand, I was thinking of switching to a spar varnish this time, in hopes of achieving better durability against the corrosive saltwater. However, I've read that spar varnish is not advised for indoor use due to the fact that it never fully cures. I was wondering if I could compensate for this fact by diluting the varnish 1:1 with mineral spirits and applying twice as many coats? This would also allow me to ha…
-
- 6 replies
- 3.7k views
-
-
I am trying to stain a Maple mantel dark. I have a custom color in OLd Masters wiping stain. I have tried the 1# cut sealcoat method and it had helped the blotching just fine. I am having issues getting the color dark enough. I am told I can seal over the stain and add stain again. But this is getting too thick and I do notlike the apperance as too much grain is lost. Charles Neils product is interesting but all the samples and video I comes across are using water based dyes. Has nayone used the product with oil based pigmented stain? are the results and better than the cut shellac as far as using oil? I know I can use the GF gel stain but its not my color. thus the O…
-
- 2 replies
- 3.2k views
-
-
Yet another neophyte to the world of wood here who is looking for guidance on finishing. So far, I've cut down a piece of red oak plywood to 3'x6' to be used as a desktop (the legs are metal and already done. I just need the top stained). I'll be applying edge banding to the sides and then applying the stain/finish. It's that last part where I'm looking for help. I've done a bunch of net searches, read Jeff Jewitt's "Spray Finishing Made Simple" and watched the super helpful Wood Whisperer video "You and Dye". Even with all that, I'm still not certain about my approach. I've gotten my hands on an HVLP spray gun and this is what I'm thinking: 1. Spray with water to r…
-
-
- 9 replies
- 4k views
-
-
There are hundreds of ways of to go about it and I'm thinking of trying something new; what is your preferred way of finishing a dining table? I have one that is arts and crafts style out of quatersawn oak and highly figured curly maple, another out of teak and a third out of walnut and purple heart (all solid stock). Is there anything you've done that you would do again or something that you've heard of that you want to try?
-
- 4 replies
- 3.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·