Finishing
2,922 topics in this forum
-
I just bought an old treadle sewing machine & cabinet and I want to restore it. Most websites I've been to recommend redistributing the finish with an appropriate solvent, but I don't think that's possible with this particular piece - at least the top. Its pretty chipped up and some of the veneer has fallen completely off. The few sites with complete refinishing instructions usually have pieces that were left outside or in barn and are pretty far gone. I'm trying to find a happy medium. If I leave it as is, chips and all, how do I seal the bare wood areas to prevent further deterioration? Or can I simply refinish just the top surface, which has almost all the d…
-
- 4 replies
- 7.3k views
-
-
We had a lively discussion going that did not match the OP so I am jumping here. The question surrounds drawer bottoms that are slid in at the end of drawer box construction rather than captured by construction. I have repaired so very many bottoms that did not stay put when inserted rather than captured. I was asked if the drawers were of sufficient quality in general or if the quality was poor. The two most common repairs I have made are sliding bottoms, and missing or crappy guides/slides. I have not needed to repair many drawer carcasses themselves or cabinet carcasses. With this experience (admittedly limited) I am wary of recommending a slide in drawer bottom. Am…
-
-
- 33 replies
- 9.7k views
-
-
Every time I try to pop the grain on curly maple it doesn't seem to penetrate into the curl any more than the normal wood. I watched the video and did the same thing, why won't it work?
-
- 5 replies
- 2.9k views
-
-
I'm going to use a simple varnish on the armoire. Should I finish the inside of the armoire, or just the visible parts? I'm in Arizona so I'm not worried about humidity and seasonal movement. Adam
-
-
- 2 replies
- 2.7k views
-
-
Guys, I am building my all maple drawers for my new Greene & Greene kitchen. I am really new at spray finishing. I have an Earlex 5500. I was thinking of the spray sequence on my drawers. I'm not sure the right order but was thinking: 1. Round spray pattern to hit the inside corners. 2. Vertical fan pattern to hit the inside of the sides, front and back. 3. Vertical pattern to hit directly down on the drawer inside bottom. 4. Vertical pattern to hit the outside faces I figured it would not be necessary to finish the bottom. Finish is GF Endurovar Slides are Blum soft close undermount. Did I figure right on the spray sequence?
-
- 19 replies
- 7.5k views
-
-
I am trying to give oak an aged/weather look. I have found a vinegar with dissolved steel wool combo that gets me the color and look I want. However I can't find a top coat that works. The vinegar mix gives a beautiful gray color, and lets the grain / age shine through. However every topcoat I have tested turns the coloring to more of a black than a gray. I am really driving for a weathered look. Any recommendations? I can say that GF Topcoat, mineral oil, and Minwax poly have all left it black. Thanks in advance!
-
- 8 replies
- 3k views
-
-
I am in the process of refinishing an old builtin break front, I think it was built around 1915. The people before me decided the quartersawn white oak would look much better if they painted it white. I sanded off the white paint and am now trying to get as close as I can to the original finish. There are a few places where the original finish seems to be intact, it looks to me like a pigmented stain with amber shellac over it. Putting the amber shellac over the bare wood didn't look right -- too orange. I have played around with different stains and such and I think an oil based pigment stain with amber shellac over the top looks like the best match. I was thinking…
-
- 3 replies
- 2.9k views
-
-
This is on sale at a local tool supply. I was wondering if anyone had any input on it? One reviewer said it was not appropriate for atomizing topcotes. I thought this odd, as is that not the purpose of the machine? Any input appreciated! http://www.busybeetools.com/products/SEMI-PRO-2-STAGE-SYSTEM-FUJI.html
-
-
- 15 replies
- 5.5k views
-
-
I've used a certain kind of drying rack that is perfect but I can't seem to find one online to purchase. It has two sides with adjustable racks for holding larger or smaller wet pieces. It's white, has rollers at the bottom and can hold a large amount of weight and boards. When all boards are off, it's extremely light. Any one familiar with this kind of portable rack? I know it wasn't custom because I've seen the same racks at different cabinet shops. Any help would be appreciated. Thank you!
-
- 4 replies
- 2.9k views
-
-
There was a recent project on TWW by Riley, which excellent job Riley!! caught my attention. Not so much the project, which was great, but the choice of finish. I have sprayed way more paint than shellac or varnish or poly, etc. but have never sprayed oil based paint before. I figured oil based was on its way out - a product from yesteryear... The author brought up an interesting point about sanding down the primer, which is something a pro painter told me long ago as well. Only having used latex mostly, I would skip this step since it takes too long for the latex to harden sufficiently to sand. Does anyone else have experience spraying oil. Care to discuss your exper…
-
- 1 reply
- 2.8k views
-
-
I'm going to be working on a project at church where I'll have to match the finish on the pews that we are buying new, i.e. altar, railings, and trim I'm building/installing need to match. They use MinWax stain (that parts easy), with a pre-cat lacquer finish for the pews. I'm going to get samples from them, but does anyone have any recommendations on what I should use to match the sheen of that lacquer? I expect it will be between a satin and a semigloss. I have the ability to spray (never tried lacquer though) and use mostly General Finishes products. Will be using red oak. Thanks for any help!
-
- 6 replies
- 3.1k views
-
-
What the best finish to bring out the red in cherry? Or does that happened. On its own?
-
- 10 replies
- 3.9k views
-
-
I've been experimenting with making some parquet flooring. I used some sticks of firewood. These two photos show the results; one is walnut and the other is oak. I spent quite a bit of time slicing up the firewood but I loved the idea of taking something that was essentially free (got it from a friend) and making something artistic out of it. I poured some Mirror-Coat epoxy over it which served to lock it all together and also provided a surface finish although I imagine it's too shiny and plastic-looking for many. Also, the oak one ended up with lots of bubbles in the finish because I left it too soon. I popped lots of them but them come out long after I thought …
-
- 4 replies
- 2.9k views
-
-
Hey Guys - Usually for finish I make my own oil/varnish blend with boiled linseed oil but I've recently started making these coffee stands and need some more of a film protection for water. I'm really not a fan of thick film finishes however and am looking for advice on an in-between type of finish that keeps the properties of oil but adds more protection. Any ideas? Also, here in CA we can't get Arm-R-Seal so that's out of the question.
-
- 4 replies
- 3k views
-
-
Hi everyone! I am new to the forum and I realize that perhaps back in time this question must have come up many times but I can't find anything specific as I go back in posts. I am thinking of taking on a task that seems monumental to me and that is making my own kitchen cabinets. One of my biggest concerns is the finish. I am planning on making the boxes and the faces and having the doors made by someone who has the tools and experience. My question is how to I go about finishing them. Do I need to pay attention to wood grain differences? Cherry darkens differently per board. What is the best way to stain them? What finish should I use for top coat? should I brush or spr…
-
- 9 replies
- 3k views
-
-
hello everyone I'm new to this forum and I've enjoyed reading through the forum. I'm hoping to get some advice or feedback about finishing my walnut tabletop. after some research i decided to go with watco danish oil, behlens garnet dewaxed shellac and behlens rock hard tabletop varnish, all of which i have never used. right now i have 2 coats of the oil on and I'm thinking i made a mistake and should have put the shellac on first. could someone please let me know if this is ok or what. i should mention that durability is high priority due to the 2 cats that seem to run the house.hah! hope to hear from you soon,thanks
-
-
- 8 replies
- 2.9k views
-
-
I acquired a 1940's wood, yes real wood, desk from my employer that she was going to pitch. I though I could refinish it and so far everything has been great. The desk is surrounded by large oak panels and the drawer faces have the same panels on the face with solid wood making up the rest of the drawer. I sanded the face of one drawer as an experiment. I took it down to 220 and it looked really nice. To finish it I used 2 (or 3?) coats of Minwax Polyshade (really dark Bombay something) following by 3 coats of Polyurethane Satin. The result was really nice. I moved on to the rest of the desk and everything turned out the same way. Really nice. Now for the to…
-
-
- 29 replies
- 15.1k views
-
-
Lacquer, shellac, and oil/wax all cause red to bleed from padauk and when it's next to a light wood it makes a mess. I'm about to give up mixing it with other species but I've seen it done and looking great. Anyone care to share a few secrets?
-
- 7 replies
- 3.3k views
-
-
Question for the wood Jedis. Can a spar varnish be thinned & wiped on like regular old poly? Thoughts appreciated.
-
-
- 6 replies
- 11.9k views
-
-
Are you seeing price increases on WB finishes. Here in WA the prices are climbing quickly and WB finish distributors are going back to solvent rather than stocking WB at all. Bigger places like SW have made all WB special order and the Target dealer cut the line all together. Rodda took on Valspar but WB is special order. GF is through the roof at nearly double the cost of the other brands. Yet solvent hasn't moved and may even be down a little.
-
- 10 replies
- 3k views
-
-
Ok so my uncle requested that I restore his grandfathers (my great grandfathers) chair. He wants to keep the finish as is but just about all of the glue has failed. There are also cracks that need to be repaired and one of the cross members needs to be either to be returned or repaired some how. My thought is to get a heat gun to help me loosen any of the glue that is still intact and take the piece apart and put it back together with our newer PVA glues, most likely TBII. Here is a link to pictures of the chair and it's problem areas https://www.dropbox.com/sh/znb4pyc46f1mjkx/XCZEbzP74k My question is what would you guys do?
-
- 7 replies
- 3k views
-
-
I am building a kitchen table and the plates are a very coarse ceramic type. I am concerned with scratching the finish. Is there a finish that can stand up to the "pfalscraft" type of plates, Or are we using placemats forever?
-
-
- 8 replies
- 3k views
-
-
I want to make a poly/BLO/mineral spirits blend. Do I sand between coats like I would regular poly? How long should this dry between coats?
-
- 7 replies
- 3.1k views
-
-
So...I need advice/education. I'm wanting to build a small book case for my wife, and I'd like to do a weathered finish, but I'm really open to learning all about distressing wood, and also weathered finishes. Hard to see in this pic, but on the cover of a magazine was the exact color and finish that I want to do.
-
-
- 3 replies
- 3k views
-
-
I have a reclaimed Douglas Fir mantel that is about 80-100 yrs old. It has been sawn on all sides then hand hewn and sanded with no stain or finish it is raw. I would like some feedback on my choices of finish keep in mind that I'm new to this and have little experience beyond basics. Where I purchased the mantel they recommend using Fiddes supreme wax. If I decide to use Fiddes do I need to pre condition the doug fir before applying the fiddes? I have also thought about a 3 part finish. Apply Charles Neil's blotch control then a gel stain or liquid oil stain from general finishes and a poly coat. My mantle now is raw and is light in color just don't want to mess…
-
- 0 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·