Coop Posted November 24, 2018 Report Share Posted November 24, 2018 A recent thread got me to thinking, what is the power tool in your shop that give you the Willies when you use it? Mine will have you questioning my Woodworking abilities. Quote Link to comment Share on other sites More sharing options...
B1rdhunter Posted November 24, 2018 Report Share Posted November 24, 2018 Routers are not my friend. Quote Link to comment Share on other sites More sharing options...
RichardA Posted November 24, 2018 Report Share Posted November 24, 2018 I have a finger that says table saw, but I think a router tightens my butt more than any tool and I have 5 or 6 of the damn things. 2 Quote Link to comment Share on other sites More sharing options...
Chet Posted November 24, 2018 Report Share Posted November 24, 2018 The router and for some reason its the one in the table more then the hand held. Quote Link to comment Share on other sites More sharing options...
Coop Posted November 24, 2018 Author Report Share Posted November 24, 2018 There are definately some meat grinding capabilities with a router, giving the speed and close contact, especially on the table. Quote Link to comment Share on other sites More sharing options...
wdwerker Posted November 24, 2018 Report Share Posted November 24, 2018 My grandfather taught me to remember that bandsaws are used to cut up frozen carcasses in butcher shops every time you turn it on. Frozen meat and bone don't even slow it down so give it the care and respect needed to run it safely. Tablesaws and router tables can take a board away from you in a split second but we all tend to have fingers pretty damn close to that bandsaw blade don't we ? 1 Quote Link to comment Share on other sites More sharing options...
bleedinblue Posted November 24, 2018 Report Share Posted November 24, 2018 My gut says the table saw, cause I still sweat while using it. I still visualize the blood splatter aftermath of a mistake. BUT. The only time I've had an "oh crap" moment, especially one that I didn't see coming, has been on the router table when the bit catches the grain just wrong. Quote Link to comment Share on other sites More sharing options...
Pondhockey Posted November 24, 2018 Report Share Posted November 24, 2018 I'm still getting more comfortable with the band saw. Like Werker, I inherited (for me maybe an irrational) fear of the bandsaw from meat cutting days. On the other hand, I've already flung enough wood from the table saw and even the router table, to have enormous respect for them. And since the jointer has an exposed cutter, I'm always keeping track of finger location and direction of applied pressure (even when using a push stick) with that tool. I haven't yet hurt myself with a finish foam brush (knock on...) 1 Quote Link to comment Share on other sites More sharing options...
wdwerker Posted November 24, 2018 Report Share Posted November 24, 2018 My dad was explaining the jointer to my brother and took the tip off of one finger. Maybe that's why my brother got interested in electronics? 2 2 Quote Link to comment Share on other sites More sharing options...
Pondhockey Posted November 24, 2018 Report Share Posted November 24, 2018 1 minute ago, wdwerker said: My dad was explaining the jointer to my brother and took the tip off of one finger. Maybe that's why my brother got interested in electronics? That's exactly what I imagine, when using the jointer. You gave me the chills! Quote Link to comment Share on other sites More sharing options...
lewisc Posted November 24, 2018 Report Share Posted November 24, 2018 I'm gonna say the router. There's a lot of power in a small unit. The table saw makes me think twice when ripping pine. Usually the pine has a lot of tension and who knows what might happen. I was watching this video this morning. Listen to what he says at 8.35 about the Sawstop. As much as I love watching some of what he makes, he does some dodgy stuff. Even if I had a Sawstop, I think making poor decisions about how to cut something is the biggest risk. Quote Link to comment Share on other sites More sharing options...
krtwood Posted November 24, 2018 Report Share Posted November 24, 2018 There aren't any tools that give me the willies, but there are operations that give me the willies. And those operations tend to happen most at the table saw, because I use the table saw for the widest variety of tasks. But it's the sanders that draw the most blood. Quote Link to comment Share on other sites More sharing options...
Popular Post Woodenskye Posted November 24, 2018 Popular Post Report Share Posted November 24, 2018 The operator is the most dangerous. Whether we are tired, over estimate our own abilities or whatever it still comes back to the 1 person that pushes the power button. 3 1 Quote Link to comment Share on other sites More sharing options...
wtnhighlander Posted November 24, 2018 Report Share Posted November 24, 2018 For me, its a close tie between my corded circular saw, and my angle grinders. The stationary machines aren't going to jump out and get me, and best practice for controlling the stock is well defined. With the circular saw and grinder, both the material AND the tool tend to jump during a kick-back event. One reason I am shopping for a cordless circular saw is that many of them have the same or greater depth of cut as my corded saw, but with an inch less blade diameter, therefore less leverage to work with in a kick-back. And no cord to cut into.... Quote Link to comment Share on other sites More sharing options...
Mark J Posted November 24, 2018 Report Share Posted November 24, 2018 And no cord to snag distracting you from that blade. Quote Link to comment Share on other sites More sharing options...
pkinneb Posted November 24, 2018 Report Share Posted November 24, 2018 11 hours ago, Chet said: The router and for some reason its the one in the table more then the hand held. I'm right there with you Chet! Table mounted router by far. Quote Link to comment Share on other sites More sharing options...
PPBart Posted November 24, 2018 Report Share Posted November 24, 2018 For me, the scariest tool for me is my Craftsman 10" Radial Saw! 1 Quote Link to comment Share on other sites More sharing options...
Popular Post gee-dub Posted November 24, 2018 Popular Post Report Share Posted November 24, 2018 I've tried to answer this a couple of times but, I keep coming off like a sanctimonious ass . What it boils down to is that as I have learned more, I have found that the acts that used to cause me a major pucker-factor have been replaced by safe ways of doing those things. Safe operational practices are a learned behavior that replaced my guns-a-blazin-get-'er-done approach of the past. If I am approaching an operation and I do not feel good about it, I back off and figure out why. Often a clamped-on auxiliary fence, guide, a feather board, some additional stock or tool support is the answer. In the grand scheme of getting from material selection to placing a new piece in its new home, the time spent to make sure you do those one or two operations safely is small potatoes. 5 Quote Link to comment Share on other sites More sharing options...
Pondhockey Posted November 24, 2018 Report Share Posted November 24, 2018 Maybe off topic, but have you ever left a loose part or tool in a cabinet? After I get a power tool adjusted and buttoned up (say a planer,) there's a little question in my mind what's going to happen when I power it up. 1 Quote Link to comment Share on other sites More sharing options...
Tom King Posted November 24, 2018 Report Share Posted November 24, 2018 A dull brain. When I feel myself getting tired, or feel the need to push harder to get something finished, we put the tools up, and go home. 1 1 Quote Link to comment Share on other sites More sharing options...
Just Bob Posted November 24, 2018 Report Share Posted November 24, 2018 1 minute ago, Tom King said: A dull brain. When I feel myself getting tired, or feel the need to push harder to get something finished, we put the tools up, and go home. Hard lesson to learn. One Christmas Eve many years ago, I came home from a long days work and had to finish a jewelry box for my 12yr old daughter. I was cutting a piece of spalted maple on my underpowered Ryobi table saw. I pushed to hard, wood slipped, ripped cut my left thumb. Spent all of the 24th and most of the 25th in the ER (it is always a busy time of year for those folks). Daughter didn't get her jewelry box, I missed Christmas dinner, wife was extremely pissed. This could have easily cost me my real job, need two good hands for police work, but I did heal up. Left the blood on the ceiling as a reminder of "stupid is as stupid does" To answer Coop's question, table saw. Quote Link to comment Share on other sites More sharing options...
difalkner Posted November 24, 2018 Report Share Posted November 24, 2018 They aren't unsafe if used properly with proper guards in place. Do I do that all the time? Nope... Case in point is the PSA video I made in May 2017. I didn't start out to make a PSA video, rather I was going to start a project and video start to finish. This one never got past 'start'. David Quote Link to comment Share on other sites More sharing options...
Tpt life Posted November 24, 2018 Report Share Posted November 24, 2018 Hands down the chisel. It’s too light to stay in place when bumped. It is the sharpest tool I frequently use. I use it for all manner of honey-do and emergency home repairs when alertness is at a low point. It pairs with Tom’s dull mind. I don’t feel a need to be alert more than the need to complete those projects. 1 Quote Link to comment Share on other sites More sharing options...
Keggers Posted November 24, 2018 Report Share Posted November 24, 2018 In my shop the machine that gives me the most concern is the jointer. Running the board across the cutters time after time draws me into a false sense of security. I've even caught myself looking out the widow as I'm making a pass across the blades with a board. You all are going to laugh, but the tool in my shop that has caused me the most damage is the cardboard box cutter. I box and ship wood almost daily and use a box cutter when boxing up wood for shipment. I've cut fingers more times than I can count and have stabbed myself in the stomach twice when the blade slipped. It's another case of having done something so many times that my mind wanders and isn't always concentrating on what I'm doing. Quote Link to comment Share on other sites More sharing options...
Popular Post Chet Posted November 24, 2018 Popular Post Report Share Posted November 24, 2018 3 hours ago, wtnhighlander said: For me, its a close tie between my corded circular saw, and my angle grinders. The stationary machines aren't going to jump out and get me, and best practice for controlling the stock is well defined. With the circular saw and grinder, both the material AND the tool tend to jump during a kick-back event. One reason I am shopping for a cordless circular saw is that many of them have the same or greater depth of cut as my corded saw, but with an inch less blade diameter, therefore less leverage to work with in a kick-back. And no cord to cut into.... Jeez' Ross I expected you to say your "hand held bench top jointer". 5 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.