The Shop
1,954 topics in this forum
-
After a few years of annoying the wife and contemplating whether or not to build a detached shop(spending around $35-40K with no hope of resale value recovery) I figured my best way out was to live in the meager space I have and reduce sound transmission from the basement to the upstairs. The main floor of the house has 2x10 floor joists, my first thought was to rip out the R11 fiberglass a previous owner had put in and replace it with R30 batts. But the more I thought about the work involved and the questionable return in noise reduction with fiberglass batts, I called a spray-foam contractor I've worked with and he advised 6" of open-cell foam in the floor and foam…
-
-
- 11 replies
- 3.6k views
-
-
As the time gets closer for me to finally build my new shop, I am doing more research on what I should be considering. Also, what amenities do you like in your shop, or wish you had? I am aiming for something in the 32x32 size range with running water and possibly a bathroom. What are your thoughts on this? My plan is to have this as the main shop with an area designated for finishing. I will eventually have an out building for lumber storage that is not being used on the current project. However, I would be storing commonly used materials in the main shop. What else should I be considering? Thanks
-
-
- 21 replies
- 5.5k views
-
-
Just starting out as the title most likely implies. I have a random orbit sander, circular saw, and 2 drills so far. My question is if you were in my position what order would you buy tools to get into it the quickest. Keeping in mind my shop is my 2 car garage so I don't have a ton of room. Also any advice on a starter table saw would be great as it seems there's about 5000 different ones.
-
-
- 16 replies
- 4.1k views
-
-
Hi, I'm new here and new to woodworking. I built some sawhorses so that I could use them as a temporary bench while I create a bench. I am attempting to build Paul Sellers' workbench, which has a laminated top. I purchased a garage sale Miller Falls #14 (Stanley #5 equivalent), and am attempting to plane the boards down - but my sawhorses keep sliding across the garage floor. I am assuming this is because nothing is heavy enough. Are there any interim solutions that I can use until I have a full heavier bench setup? Thanks guys!
-
-
- 15 replies
- 6.6k views
-
-
here is a picture of my set-up for my palmer with dust collection, works great but I'm getting so much static I'm afraid to go near the thing when its running, pulls the hair on my mustache out at 2 feet away. what would be a good way to deal with this problem? thanks to all
-
- 11 replies
- 4.6k views
-
-
I'm finally to the point of getting tools in place in the shop and have been stuck thinking about the position of my joiner and table saw. Thankfully I'm spent months planning and have listened to everyones advice regarding 'being mobile' in such a small space. Everything is on wheels and I'll be able to move things around easily in the future. I've been planning to layout the tablesaw, outfeed/assembly table, and jointer like this initially but mostly because it allows the dust collection ports (coming off the same 6" trunk line) to be close. The tablesaw's port is on the right side and the jointers is on the left. However, the more I think about it I migh…
-
-
- 12 replies
- 3.3k views
-
-
Woot! Kapex arrived today! Got it unboxed and sitting in my miter stand. Had a bit of time to set up, but will put it through some paces in the next day or two.
-
- 3 replies
- 2.9k views
-
-
Made this mortise jig to use the bushing inserts and a 1/4 up spiral bit for my plunge router. I did not want to buy a edge guide and have to work around clamps holding stop blocks in place. If I missed anything please let me know. made 2 interchangeable panels, one to center a 1/4 by 1.5inch mortise on 3/4 stock the other to be 3/16 from edge. They have a backer and 2 alignment pins to secure in place on a 3/4"plywood which is clamped to bench. clamp work piece to plywood, align center marks and cut mortise.
-
- 5 replies
- 3k views
-
-
I'm in the process of designing a cart for my DW735 planer and I was looking for a use for the space below the planer. I could build drawers but I really don't need drawers in that location. I had the thought of turning that space into some sort of a chip pre-separator before the actual dust collector. Planer is a big source of chips so I thought more separation might be better and with the fan ejection on the DW735 it might overcome any additional suction loss... I've looked at some of the separator designs on the Internet (Thien, etc.) but these require a round enclosure. I was wondering if anyone has experience or ideas for a separator in a rectangular space?
-
-
- 9 replies
- 4.2k views
-
-
Today marked day 1 of my transition from a makeshift corner of a 3 car garage with makeshift 'tool' to my own walled off 11x22 shop. I've spent months selecting my tools and most ordered over the next two months. Shop layout: The major tools include: Table Saw - Grizzly G0690 Jointer - Grizzly 8" G0656 Planer - Dewalt 735 Bandsaw - Laguna 14|Twelve Router - PC 75182 - undecided on table/fence/etc Miter Saw - Bosch GCM12SD Dust Collection - DC-1200VX-BK1 with 6"/4" PVC pipe with Grizzly Air Cleaner Day 1 of the shop build included 13' tall wall put up and drywall'd. Next week brings taping/mudding and lighting installed. Following will be floor etch…
-
-
- 51 replies
- 13.6k views
-
-
I had been struggling to cut sheet goods for cabinets out of long, wide panels for years. There were heaps of ways I could manage it by using support stands, assembly tables and so on but I just wanted a longer wider version of Festool's MFT-3. Once I rip a panel to width I now simply transfer it to my new roll around docking station and hey presto! Click here if you want to have a look.
-
- 11 replies
- 5.4k views
-
-
I made this small cabinet from scraps a long time ago for my 1/4'' Bosch router bits. I wanted the bits preserved inside their original boxes. I would do it differently if I had to do it again (way too many screws), but it still serves its purpose.
-
-
- 11 replies
- 3.4k views
- 1 follower
-
-
I am planning my new woodworking shop (1 stall of garage really) and am thinking about a multi-purpose table. I have watched the Youtube by Steve Johnson (Down to Earth) and Marc and am really leaning toward a torsion box surface but my question is.... In the outfeed function, is it necessary to have table so high as to require outfeed slots for the miter bars or can the table top be 3/8"-7/16" shy of the top of the TS and still function safely. This allowing for a work surface that is not slotted.
-
-
- 15 replies
- 4.1k views
-
-
needed more shop storage. And wanted to build this for a couple months. Its 3/4 BB plywood and walnut trim and drawer fronts. In the back is a ct48 and a cyclone dust extractor. Its the same height as the MFT3 on it legs and o my 1 inch wider. I Didnt want to go any bigger then the MFT3 foot print. I got the idea from the FOG web sight. All that is left are the drawer fronts and finish.
-
- 2 replies
- 3k views
-
-
What do woodworking shops generally have for heat and ac and why? I'm looking into 1000sqft shop options.
-
- 6 replies
- 2.9k views
-
-
I'm about to build my first real workshop! I am building it in 1/4 of my fatherinlaws barn. It will be about 1000sqft. It looks like the original meter outside is bringing in a 200 amp service. Then it splits and sends power over to another barn from there supplying 60amps to that barns panel. My question is if I can run another 100 amp sub panel up stairs for the shop or should I have more power directed to the shop? I'll be running 110 and 220 equipment.
-
-
- 15 replies
- 3.6k views
-
-
After seeing all the beautiful shops here, and all the new equipment, I find my self in awe of all the shiny tools and machines. But I just swept the floor so I took some pics. It will probably take a few post to show the pictures. I would like to show you a computer rendering of the shop layout, but that tech is far beyond me. (see weekend night stand, in project showcase, for an example of my sketch up skills)
-
- 9 replies
- 3k views
-
-
Luckily it was just the Bowflex. Wife took over the workout room for her yoga and told me the Bowflex had to go. I found a new home for it in the shop.
-
-
- 8 replies
- 2.9k views
-
-
-
-
I modified my Delta D/C by adding a 1 micron paper filter, Dust Deputy Cyclone and steel drum. Works great, but dumping the sawdust from the drum into a plastic garbage bag is a mess. My question is can you line the drum with a plastic garbage bag to catch the dust, or will the system suck the bag in?
-
- 3 replies
- 3.1k views
-
-
While I have a shop vac/cyclone system for my sanding station, my TS and planer is hooked up to a 1.5hp shop fox, upper/lower bag type dust collector (4" hose) I have since replaced the upper bag with a 2.5 micron bag (the heavy felt-type), from the existing 15 micron bag. It made a considerable difference as far as the dust I'd find settled on flat shop surfaces. As far as the lower bag replacement is concerned, I've seen different options out there and and done some research, but it also seems that an air tight bottom bag might affect performance. If I wack the bottom bag, I will see a small puff of dust come out from it. Seems to be the same fabric as th…
-
-
- 7 replies
- 3k views
-
-
If all goes well Friday we will be putting an offer in on a house. It will have plenty of room on .85 acres for a shop in the back. My question is .... what is good and what is bad as far as those buildings go? I assume having a cheap all tin building would make it a little tougher to hang things on the wall. Then would I need an at least all wood sided building with then a possibly tin roof or shingle roof. Do these buildings normally come with any insulation or not? I am thinking I will need some insulation in the ceiling at the minimum?? Or will it be a lost cause if I do not have any in the walls? Would it be cheaper to just build my own building instead of or…
-
-
- 46 replies
- 10.6k views
-
-
I decided that I was tired of chasing tools down so I decided to invest a little money and time in my shop. I made a couple cabinets. Here is a picture of the cabinets. maybe this will inspire someone out there to spend a little time to get organized. Sent from my iPhone using Tapatalk
-
- 23 replies
- 4.4k views
-
-
I was wondering if you guys thought a 2hp dust collector would be enough for a classroom. we will have only around 5 kids working on machines at one time usualy 2-3 tools at one time. usualy being used are 2 large belt sander, 2 band saws, 3 scroll saws are the heavy used tools in the classroom. 1 chop saw and table saw but those are intermittent because I usually use those until I am comfortable with a kids using them.
-
-
- 12 replies
- 3.2k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·