Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Shop

  1. Started by rodger.,

    I have been looking through previous versions of FWW to find a chisel rack that Marc mentioned in a video a while back (think it was a live session, or maybe a guild meeting). Marc specifically dog eared the magazine to come back to the article. On the off chance, does anyone know which video or magazine it's in?

      • Like
    • 8 replies
    • 3.1k views
  2. Started by Cliff,

    Anyone got tips/resources on planning out a shop built in cabinet project? It's going to be my main tool storage. Think.. Marc's tool storage thing (episode 217) but around 10 feet long, 44ish inches high, fastened to the wall. No lid, will be doors. I want to have room for 4+ systainers, even though I only have one. Then just a place to put my other power hand tools in the cubbies. Thinking of taking 6 inches at the top and making 5 foot wide sections that I can store sleds in. Oh - and maybe some drawers. Like if the 10 feet was evenly divided into 5 sections 2 foot across, I could take one column and make drawers. I don't really know what distinguishes a built in from…

  3. Started by Madkrafter,

    My garage space it TIGHT! I had some extra material in my way from another project. When I bought the Melamine (technically Roseburg Duramine), I intentionally overbought because I wanted to build a cabinet under my table saw extension. I actually rebuilt my extension table, adding 6" making it 42". I then built the cabinet with drawers and router space. I added supports under the table that acted as dividers for the router space. I mimicked those dividers in the cabinet below to close off the spaces. I built the cabinet separate from the table with leveler feet so I could raise the cabinet up to the extension table. I added some rigid foam tape to seal the spaces. …

      • Like
    • 25 replies
    • 9.4k views
  4. Started by Janello,

    Some pics of my shop interior. I still have a lot of finishing touches to do, but it's getting there. I did most of the interior work myself, including insulation, drywall, electrical and wood paneling and trim. The double door leading to the finishing room was special ordered at Home D.

    • 21 replies
    • 4.4k views
  5. I read this tip in the October 2014 issue of Fine Woodworking

    • 7 replies
    • 3k views
  6. Started by Brendon_t,

    hey guys I'm thinking out loud right now so please feel free to interrupt the train of thought. I have a few Granger supply bounce house blowers with two horsepower motors rated at 500 CFM. I was wondering if this would be adequate to use as a movable dust collection unit. My vision being to add some 6 inch hose to the intake port stepped down to a 4 inch port on all of my machines then attach a 5 micron bag to the blower side. I suppose I could also put a few wheels to make it easier to roll around the shop. This blower came from a store I used to work in that sould bounce house equipment I borrowed it one day to help drive some carpet after a flood and totally forgot I …

  7. Started by rodger.,

    So I have had this ridgid dp1550 in my shop for a few years. I am finally getting around to tuning it up for furniture making use. I levelled and squared the table to the bit, but I am getting some runout, and I don't know what good tolerances are, or how to cure what ails me. So I started by cleaning the chuck (spraying up into it with wd40), and cleaning up the area. I then found a drill jobber (to use as a refrence pin) and used my calipers to make sure it was a consistent diameter. Same measurement at multiple points. Then I set up dial indicator, and zeroed it. Then, turning the drill by hand I got a max reading of 28 or so on this dial. I th…

      • Like
    • 42 replies
    • 7.4k views
  8. Started by duckkisser,

    The more I use my shop the more I realize that I don't like standing up to get to my tools on the wall. So I decided to build a drawer set under my bench then I can just reach over and pop upon a drawer and set up my chisles/gouges on my bench top rather then hang on the wall. I remember seeing in a magazine a chisle case that flips open and doubles as a stand but I can't find a picture or desighn of it. It looks something like this but had seperate compartments like a silverware orginization tray. Can anyone provide me with a link or magazine date of a chisle storage case that turns into a stand. https://www.pennstateind.com/store/PKBOX2T1.html

    • 0 replies
    • 3k views
  9. Started by davestanton,

    Hi Guys. I have finally got around to starting my temporary shop tour video series. I have removed the video as I will soon be doing a complete video of the new shop.

      • Like
    • 162 replies
    • 42.8k views
  10. Started by Cliff,

    My garage is detached, no insulation, walls, etc. I'm in IL and winter sucks. I want to be able to decently heat the garage and keep coolish in the summer. I went to the energy star website and it said R40-R64 minimum for IL. Lowes site said R22, and I don't know what the US gov site says cause it was built in 2002 and won't display here at work - which, fyi, is a US government office building. So this tells me someone is out of their mind. You guys with shops in similar climates, what are you running? Lowes has R30 unfaced insulation, 15" x 25' for $13 (though their website seems to indicate you have to buy 12, hopefully not.) I know if I buy that then I would need t…

      • Like
    • 13 replies
    • 3.7k views
  11. Started by duckkisser,

    So what is the down side to having a separator for my dust collector? I know it might cut the suction some but how much suction will I loose? Also I have a smaller 1hp dust collector that I thought to convert into the separator. Can i use the central piece of metal that my two bags attach too and make a thien seperator over a garbage can?

    • 3 replies
    • 3.1k views
  12. Started by Woody1,

    Hi everyone, I'm still new to woodworking and am having some serious dust issues. I have a very small "shop" in our laundry room (basement) and my wife is going crazy. Not to mention its really unhealthy to be breathing this air. Any time I turn my table saw on the room becomes "hot boxed" with saw dust. For the most part I have cheap Ryobi tools and mostly use the Ryobi table saw, sander, jigsaw, and miter saw. Any suggestions for a good dust collection that won't cost an arm and a leg? Thanks!

    • 12 replies
    • 4.5k views
  13. Insulate the crap out of it! I put R19 in the walls, R44 in the ceiling, plus used expanding foam to seal all the cracks. In the winter, if the low temp was 0-10F, the inside temp would settle at 44-48F with no heat running. The few times it was -5 of below it would be around 40 in there. It was nice not having to run heat while not in there to keep waterbornes from freezing. What really surprised me is how well it has worked in the summer. People that have been in there on hot days can't believe it's not air conditioned. It's a little more humid than an air conditioned shop, but 78 inside when it's 99 outside feels pretty darn good! Here it is after the sun beating on…

      • Like
    • 27 replies
    • 6.4k views
  14. Started by Jasahan,

    So, had a brilliant idea to collect some of the dust from my miter saw. A hood connected to my shop vac. However, I didn't have a hood. But I did have a bunch of 5 gallon buckets. So I cut a hole in the bottom, stuck the hose through the hole, slid the bucket over the slide on the saw, and tried it out. Didn't do a thing. Maybe kept about a third of the dust from flying all over the shop. But not because of the shop vac. So, don't do this. It doesn't work.

    • 4 replies
    • 3.2k views
  15. Started by N00b-in-training,

    Installed new shop "A/C" today, on the coolest day I've had in a month. Sent from my iPhone using Tapatalk

      • Like
    • 9 replies
    • 3.2k views
  16. Started by Jasahan,

    Just so you know, I did try to search the forum and google for some basics, but couldn't find what I'm looking for. Any good sites/sources that sum up how to effectively hook up dust collection? HP, hose size, hose length?, how many machines, etc? I have 4 things available to me currently, and will upgrade to a serious system eventually. But here's what I got now 3HP Woodtek 2HP drum top with baldor motor 1/2HP Drum top with baldor motor Shop vac (which I use for sanders) Not asking for you guys to do the work for me, but thiught I'd let you know what I have. Anyway, just lookin for some rough guidelines.

      • Like
    • 34 replies
    • 8.7k views
  17. Started by shaneymack,

    Bought a cyclone that does a crap job of actually seperating. Got sick of having to waste a bunch of time cleaning the filter. Here is the solution; Outside, the big one next to dryer vent; What a difference. Waaaaay more suction and waaaaay less noise. I didnt think it would make that big of a difference. Really happy with it. Not sure i will feel the same when its -30c outside but we will see.....

      • Like
    • 25 replies
    • 6.7k views
  18. Started by Mzdadoc,

    I now installed three ceiling fans to keep air moving. Can't complain my garage went from 87 degrees to 86 after I installed them. I had to go inside and grab my hoodie. Lol

      • Like
    • 2 replies
    • 2.7k views
  19. I'm planning to build this design by Marc Adams/Fine Woodworking out of MDF as his plan calls for, but I'm concerned about two things: 1.) An MDF surface will mar easily. Should I go with it anyway or surface with formica? And what adhesive will work best and allow it's replacement periodically without damaging the MDF? 2.) Allowing for a miter slot. Any advice on locating for this design? Also, anyone build this? Thanks http://www.finewoodworking.com/woodworking-plans/article/working-class-router-table.aspx

      • Like
    • 12 replies
    • 4.1k views
  20. Started by Peter Brown,

    I decided to locate power for my bandsaw and table saw in the center of their respective ceiling areas with the idea that a +/- 4 - 5 ft arm on a center pivot would allow this cord to be kept out of the way and allow mobility for the tool. A bigger issue for the bandsaw than the table saw. I can't find something ready made but feel it must exist somewhere. Any ideas?

      • Like
    • 5 replies
    • 3.2k views
  21. Started by Tom Cancelleri,

    A topic I don't think is discussed all that often, other than maybe rag disposal. How many of you have an up to date fire extinguisher in your shop? I just ordered 2 5 pound ABC extinguishers for the shop since mine is coming up on needing recertification. What other precautions and items do you keep on hand in the shop in case of issues?

  22. I'm looking for ways to restrict the usage of some power tools (generally large tools, like a bandsaw, lathe, etc.) in a shop to certain individuals. Say, for instance, the tools are in a multi-purpose shop in which some people will not have been trained to use these particular tools, and as a matter of safety I would like to prevent them from even turning the tools on. The same principle would apply to a home shop, like in a garage, where children might have access. Does anyone know of any sort of key, lock, pin pad, or any other kind of device that I could attach to these tools that would prevent people from using the tools unless they were able to "unlock" the devi…

      • Like
    • 23 replies
    • 4.9k views
  23. Started by socoj2,

    i got some corian counters and a nice island about 38x48. for a song on Craigslist. turns out its only half inch =/ guess ill have to do something intersting with Ttrack and MDF to make a clamping/outfeed table

    • 1 reply
    • 3.1k views
  24. Ok, so this is my winning thought at the moment for my miter saw station build. Original Idea ... My thoughts are to get plenty of drawers in there for storage to help around the shop. Also, to integrate the spindle sander at the end of the left side as well. It would sit flush to the top so if I do have a long board it would act as a support when not in use. The shelves under the miter saw I am not sure what to do with, but maybe I will try and figure some sort of dust collection solution to be in that area? Also, the drawers next to the miter saw, it just seemed like a good idea since they are smaller, to have more of those in that area. Am I missing…

      • Like
    • 35 replies
    • 8.2k views
  25. Started by duckkisser,

    So I have a space in my shop that I have a floor intake from the dust collector for chips that come from my lathe. I want to keep it but I also don't have enough room to not make use of the floor space. So I thought to build a stand and pipe the floor cleaner through the stand to just under the stand. Then I can sweep my chips into the intake. The stand is to put my scroll saw on but also for storage underneath I have a couple of options for what to use the space under my scroll saw for. One for stuff to use with my table saw, sleds and jigs ect... Or I could build the stand into a separator for my dust collection. I don't have room for both. I know a lot of peopl…

    • 5 replies
    • 3.4k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.