Skip to content
View in the app

A better way to browse. Learn more.

Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Shop

  1. Started by Fix-it Man,

    I have been putting together a dust collection system in my small workshop. I have a excess of shop type vacuums so I deiced to use two of them for my system. They are connected by a "Y" type PVC connector to my system. I took two 5 gallon buckets and put them together to make one unit. I have a Thien baffle in the upper part of the unit. One of the vacuums has more suction than the other. My question is, am I getting any benefit from having two vacuums or is the one with more suction some how diminishing the weaker one?

  2. Started by estesbubba,

    I watched the remaining Roubo videos and realized that I'm getting towards the end. A lot of smaller things but nothing like the base and top slabs. Once I get everything put together on the floor I don't think I want move this beast. I'm wondering if there are any good reasons to have the vises on the wall side or open side? If I put them on the wall side I would have at 4 1/2' of space between the wall and the outlets right there. If I put them on the open side I would have more room and natural light from the window during the day. The downside is farther away from outlets and when heater runs the tail vise corner would get some warm air blown on it. I checked with las…

  3. Started by tedfmcm,

    So my basement shop is getting close to done...i have a variety of tools and the electrical is all run (4 sets of 115v 20amp and 230v 15amps next to each other on that wall with the door), but the wall dividing my basement (part of the full gutting) is framed without sheetrock. My shop is a mess right now with the renovations so I'm not sending pics yet but hope to get it pretty close to wrapped up after Christmas. That said, here is a (very) rough outline of the shop right now. The only things not in place are the to-be-built roubo (will take the place of saw horses where the miter stand currently is and find its way under the lumber rack when i actually set it up). …

    • 3 replies
    • 4.1k views
  4. Started by Sean Davis,

    I have no shop away from my living area. I have turned one of my bed rooms into my shop. It's 14'x14' design is very limiting. I do have shelves, a worktable I made but it could be much better. My table saw is outside, several festool sanders, jigsaw, domino 500, track saw, vacuum, plunge and fix base router and drills. Anything I have must he portable and small. I have no space for permanent equipment, so it must be able to he moved. So here is my question. Which equipment should I look at getting next? I thought of plainer, 10" drill press, spindle sander or..... I do work from making small spatulas, counter tops (I can make it work and funny to look at) and shel…

  5. Started by rodger.,

    Today, i took down the last piece of pegboard in my shop. This is my third garage shop, and i have had a full wall of pegboard in each one. I decided that i was tired of the look, and reorganized a pile of stuff. i made new, dedicated, tool holders. i also made a new saw till (samurai sword style), and built a pile of storage in a new miter saw cabinet. shop tour will be coming soon! anybody interested in buying couple hundred pegboard hardware pieces?

  6. Started by rkrueger,

    One of the two fluorescent light fixtures I have in my garage/shop has started to flake out on me. I've determined it is not the lamps. In my researching of troubleshooting the issue, I decided I wanted to replace both fixtures and subsequently fell into the abyss of options, light color, led vs fluorescent, etc... I spent maybe 4 hours last night researching and looking for what I thought might be right, including the Wood Whisperer post made on the subject, and I have yet to come up with something. I'm hoping someone here may have some advice for me, or some product suggestions. I don't need a lot. My garage is a typical 2-car sized garage that is currently lit by tw…

    • 11 replies
    • 3.6k views
  7. Started by Tom Crawford,

    Went down to shop, turned on the lights (fluorescent) and started some layout work. Had trouble seeing the pencil marks - Is this a #4 pencil? No it's a 2. ???? Set up a spot light - hmm that sure does not seem very bright for 60W - struggled for a while. Ok pause that, need to cut some boards down to a little over needed length at chop saw. What the hell, is motor dying, blade sure going slowly. Thought a moment, got out the volt meter - 120v outlets are 66 volts. End of shop work for the day. House is on different meter and power was fine there. One of the downsides of living almost in the wilderness - but view here is wonderful, no traffic noise, no smog, no light …

  8. Started by bushwacked,

    Once I finally get done with the home Reno I will be working on my garage shop. I just want to start planning now so I can get an idea of costs. My question is... If you could choose your perfect walls, what would they be? I am thinking OSB and paint them a bright white ... Thoughts?

      • Like
    • 38 replies
    • 18.9k views
  9. Started by sjk,

    I'm going to add some wiring to my garage shop before I finish insulating and drywalling it. I've read through a pile of threads here and elsewhere and am confused. To make sure I have headroom, I looked at the manuals of several big 5hp machines at Powermatic, Oneida, ClearVue, and Sawstop. I found listed amperages of 28A (like on the PM 209 planer), 19.5A (Oneida Super Dust Gorilla), 21A (PM2000 table saw), 30A (ClearVue), 20.5A (Sawstop). I don't see myself buying 5HP machines, so I'm thinking those would be upper bound. In forums, including here, I see conflicting things like "I need 40A" and "I run my whole shop on a 50A subpanel". I'm planning on adding 3 220v …

      • Like
    • 45 replies
    • 9.2k views
  10. Started by wdwerker,

    Finally found a new space for my shop ! Yea ! Now I have about 45 days to clean out 25 years of scraps and crap then move what's critical. Going to get pictures and measurements next week after I finish the Curio cabinet and a couple of little side jobs. Long hours and backaches in my future !

  11. Started by ChrisG-Canada,

    Lately I've been doing a lot of research about using vacuum pumps and bags for veneering. I've read a lot and watched quite a few videos. I'm pretty confident I can make a vacuum bag using some heavy gauge vinyl and a few miscellaneous fittings/connectors, etc. My current need is to attach ⅛" shop made veneer panels to both sides of a 1" thick BB plywood approx 30" x 44". I'm still confused about the vacuum pump itself - what type/size, etc. should I get? How much vacuum should it draw? How many cfm? Continuous duty? I only have a small pancake compressor (for brad nailing only) so I'm not sure if the Venturi style is an option for me. I found what seem to be task sp…

      • Like
    • 9 replies
    • 3.8k views
  12. Started by estesbubba,

    I got a Kindle Fire HD 7 on Amazon Prime day for the shop and the speed and reliability just isn't there. If I stream video and run the audio through my bluetooth stereo receiver, it's really iffy. Same doing Spotify and SiriusXM it works for a while then done - reboot and start over. Add on top of that it won't play videos to my Fire Stick which is dumb. So I'm thinking about getting a Chromebook which is cheap, has good battery life, and pretty light. It can do all the internet, mail, and video stuff I need plus has HDMI and bluetooth. I keep my documents on Google Drive that that's not a problem. The only downside is it wouldn't run Sketchup but I generally wouldn't d…

  13. Hi all! I'm setting up a new shop in the basement of my rented house, and would like to some feedback to make sure I have considered all the right things. The basement is unfinished with a concrete slab. The downstairs holds the laundry and the HVAC equipment. My plan is to carve out about half of the basement, using 2x4's and plastic sheeting to create a dust barrier. I want to make this knockdown so that it is easy to take apart when I move out in like 3 years, but don't want anything permanent for the same. I will probably anchor the framed out space to the concrete and the joists above. I am also thinking about putting some air filtration into the shop with b…

    • 3 replies
    • 2.7k views
  14. Started by Tom Cancelleri,

    With the new planer arriving next week I need to think about where it's gonna go, it's not gonna be mobile like the 735 is. I also need a more efficient setup and to start thinking about ducted dust collection. Here's my current layout (I moved some stuff like grinders, tormek, and bench top HCM and tool bench to the utility room in the basement to make some more room in the shop. New idea for setup. Can't find a good spot for the drum sander though. If anyone has any ideas on how to improve on this, please by all means make your suggestions.

      • Like
    • 31 replies
    • 8.3k views
  15. Started by rodger.,

    I have been drooling over getting a Festool boom arm kit for a long time. I jiggled things around in the shop, but there was still not enough room to make it worth the while. Anyway I arranged it, the vac would be in the way. So, as all shopies do, I went and looked around for a better way. I came across a good post on FOG, and did a similar design. I decided to use the wall space I had next to the bench. I used a plumbing flange, and connected a 1" 90 degree elbow to it. Then I put a 1" by 4" nipple on the end. I place a 1.25" EMT 90 degree elbow over the nipple (fits very well) and then attached a 48" piece of 1.25" EMT tubing to the elbow. This allows the boom a…

      • Like
    • 17 replies
    • 11.3k views
  16. Started by rodger.,

    Need to do something about standing on concrete when working in the shop. Was thinking of perhaps using horse stall matts to do the entire floor. Anyone use these before? About 50 bucks each, and each mat weighs a whopping 100 lbs (6x4 and 3/4 thick).

  17. I remember reading an article/review on air filtration systems like a year or more ago. I can't remember where I read it and it's driving me crazy. The article tested several different systems and had multiple graphs showing % of fines in the air over time. I've tried the usual search engines and no joy. Do any of you remember seeing that article? Where?

  18. Started by drzaius,

    Last winter I decided that I had to get serious about dust collection. I'd been using a good shop vac with a Dust Deputy which worked great for small machines, but not for my contractor saw & it was a huge pain constantly having to move & trip over the hoses. After a ton of research I decided that a stationary ducted system (Oneida V-5000) was in order. But that still wouldn't completely control the huge cloud that emanates from that contractor saw every time it's started. Again, lots of research told me that a cabinet saw was the way to go & that the SawStop (36", 3HP PCS) was pretty good in that arena. If I was going to do a ducted installation, then I might…

      • Like
    • 31 replies
    • 7.1k views
  19. Started by woodbutcher74,

    Since I have anew dust collector on the way I have a quick question. Do most 4" dust collection fittings work on 4" PVC? I'm used to dealing with Shop Vac hoses and none of the fittings ever seem to fit.

  20. Started by Gerbah from Boston,

    I was lucky enough to come across a vintage Delta Unisaw in excellent condition. In upgrading, I sold my Bosch 4100 contractor saw via craigslist. I'm now in the evening of the sale and pouring over the craigslist post as I take it down. I made a lot of mistakes, learned a lot and made some decent furniture on that tool. As much as I know I've upgraded, it's like I've parted with a good friend. Anybody else know what I'm talking about?

      • Like
    • 6 replies
    • 3.1k views
  21. Started by Brendon_t,

    While tooling around with the griz shop planner, I noticed that I'm kind of backing myself into a corner with how the big tools are bunched in the middle of the floor. My garage door rolls up above just about all of them so a drop line doesn't seem even viable. The saw is a 220 but everything else is currently wired for 110. The jointer and band saw both can switch over in the future, not sure if they need to. so my question is two fold, 1 how many circuits do you think are needed here? The DC is the only real constant that runs with anything else. The plugs at the bench will only have to support handheld power tools, the Air Compressor is a pretty big power user I belie…

      • Like
    • 25 replies
    • 7.2k views
  22. and a pretty cool shop as well when he finishes it ...

    • 15 replies
    • 3.5k views
  23. Started by Jim DaddyO,

    I got the new extension cord run out to the shop today. Not the final solution, but a lot better than the 3 smaller cords I was using, with the connectors outdoors. A small step that should get me through the winter. Actually, it has to get me through the winter as there is no other option right now.

  24. Started by bglenden,

    Hi - I've gotten the shop (which is a two car garage, which cars do not go into) cleaned up recently (so I could get more circuits put in). To prevent chaos from recurring, I need some shop storage (cabinets etc). While I could make them myself, I'm not really excited about spending a lot of time making shop furniture. Does anyone have any pointers to pre-made shop storage they like? I'm looking for medium quality (it's a shop! don't want it to fall apart!). Cheers, Brian

      • Like
    • 14 replies
    • 3.5k views
  25. Started by JosephThomas,

    Got a quick look at a former woodshop at an estate sale near me. I only took a couple pics, but I thought I'd post them here for the shock value on a couple of em....be warned, lots of softwood scraps http://imgur.com/gallery/4hVop

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,009 Total Members
  • 3,644 Most Online
  • Joseph b Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.