Chestnut Posted September 14, 2018 Report Posted September 14, 2018 50 minutes ago, pkinneb said: I know but the fact that it is taking away money from new tools still hurts BAH i got caught in explain mode. I know you probably weren't asking for the information but i like to let people know that their tax money isn't wasted, when there are enough times that it actually is wasted. Dang local gov wasting your precious tool money how dare they! Worst part is now finished space is goign to increase so you'll get a property value bump and then pay more in property taxes to boot. Gah i'm mkaing this worse aren't I? 1 1 1 Quote
wdwerker Posted September 18, 2018 Report Posted September 18, 2018 What do you do when a bookcase is 1/8 - 3/16 to wide to fit between a wall and already installed trim ? Route 1/8 deep passes 100+ times to shave the outside of the already finished bookcase. Route a groove, shift the square 5/8 & route a groove... repeat a disgusting amount of times ! 2 Quote
Larry Moore Posted September 18, 2018 Report Posted September 18, 2018 That makes for a real profitable day. Quote
mat60 Posted September 18, 2018 Report Posted September 18, 2018 If im understanding right you needed to trim not just the face frame but the side of the cabinet also. That looks like a pain. Quote
Chestnut Posted September 18, 2018 Report Posted September 18, 2018 Isn't that basically slab flattening with a tiny bit? i got one of those big 1-1/2" monster bits to do this with slabs, suppose you never use slabs though so why would you ever need that. 1 Quote
wdwerker Posted September 18, 2018 Report Posted September 18, 2018 I’ve flattened slabs with 36 grit , shims and a sled using my drum sander . I suppose I could have used a bigger bit and router. My Festool trim router has dust collection that works pretty good in situations like this . I was holding the square with one hand and the router with the other. Bigger bit & router would mean clamping the square each time. Quote
JohnG Posted September 18, 2018 Report Posted September 18, 2018 Just realized I should post an update after my previous posts regarding the hurricane. We had a few breezy days with a tiny bit of rain, but otherwise wouldn’t have known there was a hurricane causing massive damage in the Carolinas. There was a bit of tidal flooding around Norfolk, but I didn’t hear of anything excessive. There were some tornadoes in the Richmond VA area yesterday, related to Florence. This pic (screenshot from a news article) was taken less than a mile from my mom’s house, at the University of Richmond. Quote
Mark J Posted September 18, 2018 Report Posted September 18, 2018 8 hours ago, wdwerker said: Route a groove, shift the square 5/8 & route a groove... repeat a disgusting amount of times ! And hopefully after that you didn't find the needed shave was closer to 3/16 ths! Actually a pretty clever save. Quote
Mark J Posted September 18, 2018 Report Posted September 18, 2018 53 minutes ago, JohnG said: Just realized I should post an update after my previous posts regarding the hurricane. We had a few breezy days with a tiny bit of rain, but otherwise wouldn’t have known there was a hurricane causing massive damage in the Carolinas. There was a bit of tidal flooding around Norfolk, but I didn’t hear of anything excessive. There were some tornadoes in the Richmond VA area yesterday, related to Florence. This pic (screenshot from a news article) was taken less than a mile from my mom’s house, at the University of Richmond. That looks like a big one! Quote
JohnG Posted September 18, 2018 Report Posted September 18, 2018 2 hours ago, Mark J said: That looks like a big one! As far as I know that one didn’t do too much damage, I don’t think it stayed on the ground for long. There were several in the Richmond area, and another one did kill one person and injure another when a building collapsed, and caused much more property damage. My mom ended up hiding in the basement for several hours, waiting for things to calm down. Another friend in the Richmond area has a dentists office in a building that used to be a bank. They all took cover in the vault, which seems like it would be a pretty good storm shelter! Quote
Mark J Posted September 18, 2018 Report Posted September 18, 2018 6 hours ago, JohnG said: My mom ended up hiding in the basement Smart woman. 1 Quote
Chestnut Posted September 25, 2018 Report Posted September 25, 2018 I joined the no fence t-track in top miter station crowd. Have to say the dedicated stop is going to be awesome on the miter station. I made my miter station with out a fence over a year ago so i was way ahead of the curve there Marc stole the idea from me. 1 1 Quote
Jonathan McCully Posted September 25, 2018 Report Posted September 25, 2018 Bought 150 board feet of rough black walnut for a planned trestle table. Has been drying longer than I expected. Still needs to acclimate to my shop, but I can hardly wait to get started milling it. 2 Quote
Pondhockey Posted September 26, 2018 Report Posted September 26, 2018 More or less finished rehabilitating a router table that I acquired (re-drilling inserts, fixing electrical, fastening the top to the cabinet, making a fence, two different attempts at mobilizing it.) Finished up a few mm higher than my cabinet saw, so I'm scratching my head how best to tweak the saw mobile frame (shims) or the router table. By the way, acknowledgments to lots of you for ideas I've stolen, including Tom's (and many other's) dust collection through the fence. Quote
Popular Post Pondhockey Posted September 28, 2018 Popular Post Report Posted September 28, 2018 We put a version of Mark's "Not So Rustic Table" to use. 4 Quote
Popular Post gee-dub Posted September 29, 2018 Popular Post Report Posted September 29, 2018 Apparently I spent the last 3 hours selecting the parts locations out of a piece of tiger maple without making one cut. I just looked up and it was after lunchtime!?! In my defense, my shop time has been minimal lately. I may have stood at the bench with a piece of chalk in my hand just gazing out into space and soaking in the shop-atmosphere for half of that time 7 Quote
Popular Post JohnG Posted September 29, 2018 Popular Post Report Posted September 29, 2018 I made a small mallet for my 1.5 year old daughter today. It’s nothing fancy. I had a piece of scrap poplar on the bench and roughed out the handle with a 1” chisel and then sanded it a bit to smooth it out. Rounded over the edges of the head and drilled a hole for the handle, then used 5min epoxy to hold it together, and a light coat of spray shellac. The whole process took about 15 minutes, but was satisfying and fun. After she woke up from her nap, I gave it to her and she immediately ran over and started hitting a piece of wood with it. By far the most gratifying project I’ve ever done! 3 Quote
pkinneb Posted September 29, 2018 Report Posted September 29, 2018 58 minutes ago, gee-dub said: Apparently I spent the last 3 hours selecting the parts locations out of a piece of tiger maple without making one cut. I just looked up and it was after lunchtime!?! In my defense, my shop time has been minimal lately. I may have stood at the bench with a piece of chalk in my hand just gazing out into space and soaking in the shop-atmosphere for half of that time Yeah but you don't want to make a mistake with that beautiful piece of maple right there...take all the time you need 1 Quote
wdwerker Posted October 5, 2018 Report Posted October 5, 2018 I realized my ceiling fan was caked in dust and the light kit was loose, filthy and wobbly. Vacuumed the whole thing , took off the light kit, washed the glass & brass then went to reassemble the whole thing. Figured supporting the fixture while attaching the wire nuts would be difficult. Little giant ladder + Amazon box = perfect support ! For anyone with sharp eyes that's the 1984 Little Giant. It's a tad heavy but still solid as a rock. Hunter ceiling fan is a similar vintage , buy once, cry once , 34 years later both are still going strong. 1 1 Quote
RichardA Posted October 5, 2018 Report Posted October 5, 2018 On 9/29/2018 at 5:15 PM, gee-dub said: Apparently I spent the last 3 hours selecting the parts locations out of a piece of tiger maple without making one cut. I just looked up and it was after lunchtime!?! In my defense, my shop time has been minimal lately. I may have stood at the bench with a piece of chalk in my hand just gazing out into space and soaking in the shop-atmosphere for half of that time Nothing like the smell of a wood shop to make you wander your mind. Ah, the possibilities.................... Quote
Chestnut Posted October 5, 2018 Report Posted October 5, 2018 7 hours ago, wdwerker said: Little giant ladder + Amazon box = perfect support ! For anyone with sharp eyes that's the 1984 Little Giant. It's a tad heavy but still solid as a rock. Hunter ceiling fan is a similar vintage , buy once, cry once , 34 years later both are still going strong. I have a ladder and a box that look just like that. Guess they haven't changed the ladders in a long time. If it ain't broke don't fix it. 1 Quote
Chestnut Posted October 6, 2018 Report Posted October 6, 2018 Took a woodworking break. Went boating. 1 Quote
RichardA Posted October 6, 2018 Report Posted October 6, 2018 I'm eliminating some scraps or off cuts, by making reindeer and some cutting boards. It's kinda busy work, but it cleans out the short stuff that I hate to toss. 2 Quote
Pondhockey Posted October 6, 2018 Report Posted October 6, 2018 On 10/4/2018 at 10:09 PM, wdwerker said: I realized my ceiling fan was caked in dust and the light kit was loose, filthy and wobbly. Vacuumed the whole thing , took off the light kit, washed the glass & brass then went to reassemble the whole thing. Figured supporting the fixture while attaching the wire nuts would be difficult. Little giant ladder + Amazon box = perfect support ! For anyone with sharp eyes that's the 1984 Little Giant. It's a tad heavy but still solid as a rock. Hunter ceiling fan is a similar vintage , buy once, cry once , 34 years later both are still going strong. And the fan was still balanced when re-assembled?! Nice work. 1 Quote
wtnhighlander Posted October 6, 2018 Report Posted October 6, 2018 The trick to balancing a fan is to make sure the blades are all in the same plane. Pick a point on the ceiling, measure to a blade tip, and rotate the fan to see that all blade tips measure the same. If they don't, apply mechanical motivation until they do. 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.