The Shop
1,954 topics in this forum
-
I am wondering how one can determine if a power tool can be rewired for 220v. My new shop is turning out to be a bit more amperage limited than I had hoped. My electrician has told me that 220v equipment draws half the amps of 110v. I understand Ohm's Law so that makes sense but it does seem like I am getting something for nothing. Nevertheless, I wonder if any of my power tools could be switched over to 220v and how I would determine this. Thanks!
-
-
- 6 replies
- 3.6k views
-
-
Hello Everyone, My wife (Terry) and I are having a open shop/studio on August 18th (2012) from 1 – 6pm address: 9824 30th Ave SW Seattle,Wa 98126 My shop is one the ground floor ( 2500 sq ft) and my wife’s studio is up above (600 sq ft). I will have samples of my work on display and might even have some work in progress. Stop by and talk woodworking and/or Greene & Greene Any and all are welcome http://furnituremaker.com/open.htm Here are some 360-degree images that Tim Celeski took at my last open shop (5 years ago) http://furnituremaker.com/Woodworking.htm I hope to see meet some of you there! Darrell
-
-
- 17 replies
- 4.3k views
-
-
I've recently had to move my shop/residence to a new location. I've been thinking of upgrading my 500CFM dust collector for a while. Unfortunately my new shop space has only 110V 15A circuits at this time. The circuit breaker box is completely full, so there's no room to expand. The collector I'm looking at is this one. http://www.amazon.com/DELTA-50-760-1-5HP-Vertical-Collector/dp/B00078V9KA/ref=sr_1_2?s=hi&ie=UTF8&qid=1341448065&sr=1-2&keywords=dust+collector I've looked everywhere I can think of to find the actual amp draw of this unit but can't find it. Can anybody tell me what it is? Thanks
-
- 6 replies
- 2.9k views
-
-
As you see in the pictures, I have incorporated a down draft section in my out feed table. In addition, I used 3/4" holes so I can use bench dogs, wonder pups, and hold downs. I attach the handle for my floor sweep from my dust collector and plug it in. Great for cleaning off the top of the table as well. Each hole has a small chamfer... I have to do a few in the middle but didn't want to lose velocity by having to many holes.
-
- 2 replies
- 3.1k views
-
-
Hey guys, I know there is a lot of info on this subject, but was wanting some personal info on my particular setup for the garage. I have a 2 car garage that I only use one side(wall) for the shop (hobbyist). I am getting a 2HP dust collector soon, and was thinking of running one main along the wall to 3 machines (table saw, bandsaw, and a mitersaw). Curious on what you guys think would be most bang for buck setup with those particluar machines in mind for a shop that is not run as a full time job. For more information, I am insulating all the garage walls right now and will probably be installing a window A/C unit for the hot Summers and would like to be able to work…
-
- 5 replies
- 3k views
-
-
Hello Fellers I just got this article from Fine Homebuilding and some of you who live in the tundra dealing with bad weather could consider this. Hate to brag ... not We don't deal with this in Sunny Southern Cal ... but we don't have Vic's real estate either Enjoy http://www.greenbuildingadvisor.com/blogs/dept/musings/how-insulate-basement-wall?lookup=auto&V27=&V28=&V29=&V30=&V31=&V32=&V33=&V34=&V35=&V55=&V56=&Taun_Per_Flag=True&source=W2730ENL&utm_source=email&utm_medium=eletter&utm_content=20120702-complete-guide-to-paint&utm_campaign=fine-homebuilding-eletter
-
- 3 replies
- 3.2k views
-
-
I searched and could not find a slick solution for this. I'm in the process of moving my tablesaw area. In doing so, I noticed my fence is not square to the table top. I'm not talking about parallel to the blade. There IS an adjustment for that. Having the fence square to the table has obviously never bothered me, but what can I say. Now that I know it's not, it does! Has anyone come up with a slick solution? For now, I'm just shimming my subfence, but would like input, if anyone has some.
-
- 14 replies
- 10.2k views
-
-
My Upstairs shop I thought I would give you a picture with a round the shop tour. The shop is on the second floor of my commercial building. I put it there to separate it from my metal shop below. A friend of mine and I did all the construction after having it engineered. It is supported by Glu-Lam beams with I-joists. The floors are 1 1/8" decking coated with four coats of Urethane. I have access via an order picker (you know, those riding fork lifts you see in Home Depot) and stairs. Entering the shop from the stair or the lift you will see the corner. In progress is the screw and hardware storage. Straight away is a repurposed cabinet storing routers. Above are …
-
- 4 replies
- 5.6k views
-
-
Have any WTO participants installed automatic fire sprinklers in a home shop? How about a finished basement? My shop is the entire basement of my home. I'm thinking it might not be difficult to install a sprinkler system down there. I'm a really careful guy, but just in case... Here are my details: - The space is currently unfinished, save the shop machinery, benches, and shelving - Walk-out in back, floor is above grade in the rear, three sides in ground - I have excellent city water - Minimum temps never fall below ~ 52F down there - Easy access to existing supply pipe I'd love to hear experiences, costs, positives and negatives, etc... I know it w…
-
- 13 replies
- 3.2k views
-
-
You'll have to excuse the shaking. Good thing I'm not a surgeon! http://tumblewood.blogspot.com/2012/06/tour-of-tumblewood.html (null)
-
-
- 21 replies
- 5.2k views
-
-
Greetings all. I just closed on an old fire station, and wanting to use half of the bay for a wood shop. The concrete is not level in this area, and I'm wanting to build a wood subfloor in the shop area. I'm wanting to run the electric in the floor along with the dust collection. The thing I'm wondering about is will this cause any issues with the machines? Vibrations, etc. I plan on using 2x6 lumber and having 4x4 supports every couple of feet to support the weight. Any suggestions would be greatly appreciated. Thank you. Brad Doyle Belleville, IL
-
- 7 replies
- 3k views
-
-
This might be a strange topic but i have a problem with spiders in my garage. I find that when I leave my shop there are a few webs around but when I come back in the morning there are a lot more there. I was just wondering if anyone had any tips on getting rid or the spiders. I'm open to try any suggestions. Thanks in advance for any suggestions
-
-
- 26 replies
- 10k views
-
-
Here's a small question. What brand/kind of double-dtick tape do you use in the shop? I have tried two types, one was for photographs that came in a dispenser. It was too weak. The other was a carpet tape. I found that it was inconsistent in its adhesion and the residual "glue" that it leaves is a pain to get off. Does anyone have a preferred double-sided tape? Jonathan ===================================
-
- 9 replies
- 12.3k views
-
-
I recently purchased a Grizzly TS and using a 2 car garage as a shop, I need things mobile and the 1023RLWX is a heavy somebody. Mobile bases I saw on line looked a little expensive relative to the metal sitting in my rack and the wire welder in the corner. Its 1/4”-2×3 angle iron with 3/4 ply in the bottom with 3” wheels on outriggers. It easily rolls over any giblets in the floor. After I put the saw in it, I realized the Grizzly fence system rails actually support the RH cast iron table. Using an Incra fence system instead of the Grizzly, I mounted the black supporting legs directly to the cast iron table and to keep them in place and plumb, I made the red bracket. T…
-
- 3 replies
- 4k views
-
-
Hi, i have recently bought an old 3800 Beaver 6" jointer (see before/after pictures). I would like to have tips on how to set up the tables coplanar. I have read somewhere that I should shim the outfeed and infeed tables, but i can't figure how to do that and at the same time be able to set up the depth of cut. Thanks
-
-
- 9 replies
- 4.4k views
-
-
I am starting from scratch in a new 900 sq ft insulated and heated garage with a concrete slab floor. I want to insulate the floor and put down a wood floor. I am looking for the optimal solution. Thoughts include 1.5" board insulation between 2x4's face down on 24" centers. Then a 3/4" T & G plywood floor either painted or with a laminate floor. I have no clue whether this is the right way to go if there is a better/cheaper/easier solution that I have yet to consider. So OK experts, what would you suggest if you could start from scratch?
-
- 15 replies
- 11.5k views
-
-
Hi friends. Feeling overwhelmed on how to organize my mess. Now I am super equipped and made a decision to plan. The garage is so full that this becomes overwhelming. So what music to listen while cleaning all this and attempt to have a vision ... "Madness" Speak with you soon.
-
-
- 11 replies
- 3.3k views
-
-
Folks, I have finally started on a dedicated wood shop. It is going to be built in one bay of a three car garage. The back half of the center bay is a finish room. The shop bay is 25' by 11' 6". The finish room is 12' x 10'. I was fortunate to purchase a rather complete wood shop from a woman. Most of the equipment is new. I have looked for a book or some web site that will help me layout the equipment initially. I understand that everything is subject to rearranging but I am planning on a professional dust collection system so it would be helpful to get things close the first time. Major power tools: Delta 10" table saw with infeed and outfeed tables Del…
-
- 8 replies
- 8k views
-
-
I just insulated and sheetrocked the shop to prep for installing air conditioning. It's taped and floated and I wasn't intially planning on painting it, but I'm changing my mind. I find the patchy look a little distracting, and the overall color grayer than I expected. If I'm going to do it, while all the equipment is out of the shop and before I put up the french cleats is the right time. Another potential bonus to painting it is sealing the sheetrock against contaminants. Plus, if I paint it white I'll maximize my lighting. Any feedback? Any suggestions on paint type(interior, exterior, kilz, sealer, ect,) would be appreciated, I'm not a painter. Also, if ther…
-
-
- 15 replies
- 4.1k views
-
-
Anyone know where I can buy a short (two or three feet) of five inch flex hose without breaking the bank? I've found several places that have much longer lengths (for much more money) and many either won't cut or charge money to cut it. Thanks, Rob
-
- 4 replies
- 3.1k views
-
-
Ok, so this is my first post here on the forums. i am currently in the process of clearing out from my current workshop space, which is roughly 65m5. It has been a great space but unfortunately due to the fact that the building it is in is getting demolished we have all had to leave. I've had a tough first year and a had of running my own woodworking company here, ups and downs. After a busy winter, it has gone very quiet and the past couple have months and my financial situation isn't at best just now. However the business must go on and i have been actively looking for a new space. the problem is due to the financial situation the spaces that are the size of m…
-
- 1 reply
- 2.9k views
-
-
I have limited space in my shop (the 3rd bay in a 3-car garage), but it does have 10' ceilings so I thought about making a rack to store sheets of plywood standing upright since it would have a smaller footprint. Has anyone does this or know maybe where I could see some pictures to get a couple ideas of the best way to go about doing this?
-
- 1 reply
- 5.3k views
-
-
i usualy see shops with there tools spread out around a large area stationed along a wall. recently looked in a book and saw a guy who had all his main tools (table saw, router, jointer, planer, band saw sander) in a centralized area placed in such a way that the table top is all the same height. what i liked about it was he had his dust collector in the middle. seems like that would be a more efficiat way to build seeing as there will be a very short run from the dust collector to the tools. plus you can use a table surface from one machine to be the table surface for another. for example combining router and table saw top. band saw top and planer outfeed are same he…
-
- 4 replies
- 3.6k views
-
-
Hi all, I am interested in getting started with a little woodworking...ya ya, I know. That’s how you end up taking over the garage and half the back yard. Seriously though, I’m primarily a leathercrafter. I’d like to get into a little woodworking to build a couple work tables, as well as small boxes for hardware storage. Just like woodworkers, us leatherworkers run out of storage fast and often. So I’m hoping for a little advice setting up a small shop. Two small rubs however, and they are why I’m asking if it is even possible or if I’m just crazy for considering this. First off I live in a city apartment. No outside space. This isn’t a problem for leatherwork be…
-
-
- 12 replies
- 3.1k views
-
-
Most, if not all of us, are creating shops. This thread is dedicated to what inspires us. Not so much in terms of great projects but great shops. Add to this thread any photos, videos or links of shops, shop design and shop ideas that inspire you. The cream of the crop so to speak.
-
-
- 30 replies
- 9.4k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·