The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
A few months ago I bought a small block of holly for use in inlays. A few days ago I ran the sides through the jointer to flatten them out. Almost the whole thing turned a powdery blue. I sanded a spot with no difference. It's sat for a few days, hoping it would oxidize white, but nothing. 1) Any ideas why this happened? 2) What can I do about it?
-
- 3 replies
- 3.5k views
-
-
Hey everyone, I've been having a bit of trouble planing down a few species of wood, most notably Bloodwood, Paroba Rosa, Leopardwood and figured woods. The interlocking grain of these keeps causing little streaks of tearout, regardless of which way or how finely I plane them them. I've tried skewing my plane at different angles, adjusting the camber of the iron's grind, and so on. Up until now, I've been able to take rough stock of nearly any straight grained hardwood and get it glass smooth, flat and square with just my old Dunlap #5 and a 60.5 block plane (my only planes, btw). It seems that I may need another tool for cleaning up the more difficult woods, but I a…
-
- 3 replies
- 5.7k views
-
-
Hey all, I just found an interesting thing, FAS Grade Poplar and Oak in large quantities goingfor sale cheap. RIght now, they have 1500 lbs of oak going for $100 and 3 1/2 TONS of Poplar (in 1000lb lots) that should even be cheaper! THe website is www.exfactoryauctions.com and from the main page go down to the Fordyce Auction. There is a picture frame company closing in Fordyce Arkansas (south of Little Rock, AR) and they are selling out the factory. On page 11 there are 7 1000lb lots of Poplar First and Seconds that were going to be used to make frames...they look like 5/4 x 2" pieces mostly, about 9-10 ft long. The starting bid is $25... It does have a res…
-
- 2 replies
- 3.3k views
-
-
Last year about this time, I had a white oak in my backyard that needed to come down. It was experiencing a little rotting, and it was right next to my house. Being a relatively new woodworker, I wondered if I could find somebody to mill the wood for me. Well, after a good bit of research and some phone calls to various people in the north Georgia area, I found a miller and a dryer, and I was able to get about 500 bf of decent quarter sawn white oak for about 300 dollars (not counting the cost to cut down the tree). Now, I can tell people who admire my little side table that last year, that was a tree in my backyard. I wanted to let people know that it is possible…
-
- 6 replies
- 4.7k views
-
-
http://grist.org/list/heres-what-the-inside-of-a-tree-sounds-like/ Installation artist Bartholomäus Traubeck’s new work, “Years,” uses some kind of optical dealie to translate a tree’s age rings into piano music. Okay, so this isn’t quite what you’d get if you dropped a needle on a slice of tree and let it spin, but it’s still kind of cool that you can interpret natural patterns into something that sounds like Schoenberg.
-
- 3 replies
- 3.3k views
-
-
If you glue a thin veneer to a stable substrate (like MDF), the veneer will want to move with changes and humidity and such, but it won't be able to because (being thin) it can't generate enough force to overcome the glue that's sticking it to the MDF. So far, so good. Now if you glue a thick board to a stable substrate, and the baord decides to move, something has to give. Either the glue joint will fail or the wood will split or some other bad thing will happen. Not so good. So the question is, how thin does a veneer need to be so that you don't have to worry about movement issues? Can I get away with gluing say a 1/4" thick solid wood veneer to a piece of MDF…
-
-
- 7 replies
- 7.4k views
-
-
I just got home from visiting family in MO while there I met a man with a mill who is a friend of my uncle. I bought some maple as well as missouri cedar. I was wanting to make a side table, coffee table or bench out of the cedar. I am looking for a good contrasting wood to use as accents or splines int the projects. Since I brought this wood from humid MO to dry western CO I figure I will have to let it sit for a while before using it. Not sure how it will work out but at $2 a BF for Maple and $1 BF for the Cedar I figure it is worth a shot. What would be a good rule of thumb on time for letting it sit here in CO? If it all works next trip I am taking a bigger veh…
-
- 3 replies
- 3.5k views
-
-
For all the botanists out there. Is norway maple hard....soft.......crap.......furniture caliber?? Ive heard that some kinds of maple arent worth a pile of firewood.
-
- 8 replies
- 12.2k views
-
-
Is there a simple way yet effective way that a beginner can dry lumber?
-
- 3 replies
- 2.9k views
-
-
Has anyone used pure bond products http://www.homedepotpurebond.com/
-
- 13 replies
- 6.9k views
-
-
I got my hands on some old barn wood, it really did not look that nice. Well to my suprise as i was running it threw the planner this beautiful slab of wood came out the other side. I cant tell what kind of wood it is, can use some help. Thanks! Jack
-
- 17 replies
- 4.2k views
-
-
SMC members suggested I post here...I am making a project for a friend who lives in the Arizona desert (I am in Southern Missouri)... Question is, what would be a good dimensionally stable type of lumber that will handle the climate change well ?? What should the moisture content be before I work the project ?? This will be a cnc carved sign, approximately 12" x 24" and 5/8" thick. Sealed & painted. Thanks, Brad
-
- 6 replies
- 3.2k views
-
-
i am wanting to know how to decide if i want to use all of one species of wood for my end table or combine different species? ex- walnut and white oak? one or the other for legs and or aprons and top? how do you know what wood will look good together?
-
- 13 replies
- 5.7k views
-
-
I am somewhat new to woodworking, but not a beginner. However, I have never attempted this, and I haven't heard of anyone else doing it, so maybe there is a good reason for it. I recently had a very large oak tree fall in my yard. As my husband was cutting it up for firewood, I asked him to cut me a circle about an inch or so thick. I am thinking of making a table out of it. The circle is about 25" across. Would this be a mistake? Can a table be made from a circle of oak (white oak, I believe)? Is there going to be an issue of cracking? What other issues should I watch out for? Any help would be greatly appreciated!! Thank you, Terry
-
-
- 14 replies
- 5.7k views
-
-
We have some very large swamp chestnut oaks on our hunting property. Our neighbor just clear cut his place and it looks to be killing the oak trees. Does anyone know(already googled and can't find anything)if these trees have any woodworking value above red oak. Does it look like qs white oak when qs?
-
- 6 replies
- 3.6k views
-
-
Hi guys and gals, Just finished watching "A Simple Curve" it's a woodworking movie about a father and son that own a shop. The son is trying to get the dad to get real about picking jobs and being more flexable on his woodworking standards. The father is happy to ride the business into the ground. And of course some struggles with romance, etc. Background in a beautiful part of Canada. You can watch it for free if you have an Amazon Prime account on Amazon. http://www.amazon.com/A-Simple-Curve/dp/B003HMBCD2/ Do any of you have any other similar wworking themed movies to mention? MRod Colorado
-
- 3 replies
- 5.8k views
-
-
I am planning a cherry wood cabinets for my kitchen but my wife is worried that it will get too dark over time. Has anyone did any projects where you used antique white on the cabinets to make them lighter? Thanks
-
- 8 replies
- 5.4k views
-
-
What Species Is This Veneer? I have an old antique table that I am considering repairing the top on. From what I can tell the top is made of a number of solid wood frames with veneer in the centers. One part of the table appears burnt (?) where some of the veneer is gone. Options might be to replace as little as possible or the whole sheet of veneer. Larger Image Of Top: http://www.vitalbodi...1920x1080_0.jpg I thought I might ask what wood you all thought this might be? Also, what is the best way to identify wood? I have seen listings for wood identification kits like this one and there are also books.
-
- 14 replies
- 6.3k views
-
-
Name some good sources, if you have them, for antique heart pine in project-sized quanties. All-heart, tight-grained, longleaf pine, preferably rift-sawn or even VG. Who can be counted on to ship you what you need? I am talking about quantities such as for a small cabinet job, or for tables, etc. I say "antique" because I believe that the really old-growth trees were the only ones that produced this lumber in really tight grain, but hey, what do I know.
-
- 3 replies
- 3.4k views
-
-
I just got a small load of cherry and walnut from my wood guy. it's mostly 4/4 to 5/4 stuff. the lumber is dry. do i still need to put stickers between each board or can i stack one board on top of another?
-
- 17 replies
- 18.3k views
-
-
While looking for a reference on Soft maple vs Hard maple to make the roubo workbench I came across this resource from the United States Department of Agriculture Forest Service Chapter 2 was of particular interest - the rest of the book goes into what looks like Rocket science http://www.fpl.fs.fe.../fpl_gtr190.pdf (15 MB) Michael
-
- 0 replies
- 2.8k views
-
-
I'm planning on building a Morris Chair. My usual lumber guy has said "spring" for as soon as I'll see quartersawn white oak. :-/ Any suggestions for reliable sources online? Ideally stocking a small amount of 10/4 or 12/4, so I can go with solid legs?
-
- 9 replies
- 10.5k views
-
-
Found a guy selling white oak 4x4's used for shipping drilling pipe. It sounds like its to good to be true 10 foot 4x4 white oak for $5. So my question is how can I make sure that it is indeed white oak and that it will be useable to make something other than firewood? He has almost 700 of them and he will let me pick through them, they are a older (how old I don't know) so no moisture issues, and other than avoiding any knots or broken boards what should I look for? Any info would be greatly appreciated I have never bought any reclaimed wood or white oak for that matter so this new to me. Thanks a bunch in advance for the info.
-
- 12 replies
- 8.9k views
-
-
Can anyone recommend a good place to buy slabs or burl slabs? I need a piece approximately 24" in diameter.
-
- 7 replies
- 5.9k views
-
-
a guy by south end of chicago is selling 33 10 by 8 foot 8/4 old growth red wood boards for 500 dollars. that comes out to about 1.12 a board foot give or take. They come from a old water tower that he took down. i would buy them but strapped for cash right now so if anyone else wants them let me know and i'll give you his information.
-
- 0 replies
- 4.1k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·