The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
Will spalted beech be tough enough for a dining table top?
-
- 3 replies
- 2.9k views
-
-
I recently bought two 4-foot lengths of 4-6 inch poplar. It's reclaimed wood (and wet), thus it was cheap, and I intend to use them for learning projects. But first I need to cut the wood into planks so I can dry it. What's the best method of resawing wet hardwood? Can I use my table saw? I tried cutting two planks with it, and it seemed to work okay, though it made this really fine dust. I also have a 9-inch benchtop bandsaw, but the thought of using it to resaw such thick wood is enough to give me nightmares. Also, once I do have the boards cut, can I dry them in an upright, vertical position? Oh, and I'm thinking of cutting the boards into 1.15 inch planks, t…
-
- 5 replies
- 3.3k views
-
-
Ive got a project to make 6x3x3 sticker stands out of Juniper to next to retailers cash registers. They want them to have a live edge look and feel so I'm using branches. The problem I'm running into is the only juniper i have on hand is wet still ready wet drying for next years heating. I was wondering if i could put these small logs it in the oven to dry it out a little. My hope is to get some of the moisture out. Has anyone tried this? if so do you have any advice? temp and time? Thanks!
-
-
- 10 replies
- 4.2k views
-
-
Has anybody bought lumber online? If so, who do you suggest and who do you not suggest? We have a good hardwood dealer here in Toledo with some exotics but I'm just looking to stretch my horizons. We also have a good plywood dealer here also but I'm wondering if there are cheaper options out there?
-
-
- 20 replies
- 7.1k views
-
-
I have an old buckboard. Both axels are bowed upward and have wood on top of the bow. What kind of wood would be best suited to this use and does anyone know whether it would be best to shape it or bend it? Bill V
-
- 2 replies
- 2.6k views
-
-
Well, I'm a student and enrolled in an entry level woods course, which I feel is well below my level. The shop we work in is huge. We have really, really nice stationary tools. For example our helical cutter planer has a 24" depth. Yes depth, not width. Sadly just about everything else is lacking; I can run my finger back and forth with mild pressure across the edge of any one of the chisels without fear. Don't even get me started on the lathe tools. Anyway, I need to resaw a 11/16"x6"x24" board into preferably 4 pieces. The bandsaw the shop has is really nice, a 24" monstrosity with bearing guides and the whole nine yards. However, whenever the blade guard is tighten…
-
- 5 replies
- 2.9k views
-
-
I've heard that many shipping pallets are made of woods that are exotic to the US. I found this in a pile the other day and thought that the grain was pretty so I salvaged it. I was think it would do well in a small coffee table. Can anyone tell me what kind of wood I have here?
-
-
- 20 replies
- 4.7k views
-
-
Hey, fellow Illinois woodworkers. Can you reccomend any good sources for quality hardwoods in central Illinois, particularly around Bloomington, Peoria or Champaign? Thanks.
-
- 4 replies
- 7.5k views
-
-
I live in the Charleston, SC area. A friend found an 8 foot log on his property and decided to mill it. It's very heavy and has a very interesting grain. Any ideas what type of wood it is? Thanks, Bob Devereaux
-
- 4 replies
- 3.1k views
-
-
quick question which i think I already know the answer to but I'll ask anyway. I have to make up a desk top and the client wants to use hickory. My local sawmill guy has some he has been air drying for about 4 months and it is at 16% M.C. I don't have time to let it acclimate in my shop. I basically need to make up the top and deliver it by the end of the week. My other option is my local hardwood dealer who's hickory costs twice as much but is probably at a workable M.C. So my question is am I doomed if I try to use the sawmill's boards with that high of a M.C.? i will need to join 4 pieces 46" long to make a 46" x 26" top and two more 4 piece tops 23" x 26".
-
- 2 replies
- 2.4k views
-
-
First off, new poster. I have been reading for weeks now glad I found this site, got a lot of great tips. I am fairly new to the hobby and really enjoy my time in my shop. On to my point. I picked up a shipping crate at work today and after a little research from where it came from I was able to determine that it is okoume. The question being has anyone used it. The web says its used for a lot of sheet goods but this is a solid board crate.. its tight grained moderatley soft and pinkish color with a curl look to it similar to maple.... just wondering if anyone has used it before. I'm thinking keep sake boxes and other small stuff....
-
-
- 4 replies
- 3k views
-
-
I bought some Babinga to make a box. When I went to plane it started to chip out. I know its not dull knifes i replaced them right befor starting the Babinga. I tried smaller cuts but it still chiped out. Is ther any thing I can do to help/stop this frome happening
-
- 6 replies
- 5.6k views
-
-
This wood is used for the drawer sides on a 85 year old dresser and chest-of-drawers. All the drawer sides are 3/8" thick and this beautifully fidured wood. Thanks, Tom
-
- 9 replies
- 3.1k views
-
-
Last time I was in Canada, a friend who lives in sticks loaded me up with some lumber from trees he and his wife had felled on their property. They were milled, stickered, stacked and air dried in their barn. The next project on my bench is a couple of end tables, one for my mother and one for Doug and his wife as a thanks (quite literally loaded up the floor of a small U-haul). The one for my mother is butternut (which milled completely fine), and the one for my friends is maple. I started milling some of the maple last night and there appears to be some defects in it. I'm not sure if it's a result of case hardening or what exactly. At first I thought it may be som…
-
- 16 replies
- 6.1k views
-
-
hey anyone know of any lumber mills or reputable stores in south beach area. got a budy down there that wants to make a walking stick for his dad. but he needs lumber.
-
- 0 replies
- 2.2k views
-
-
I live in SW Missouri. We have a lot of trees. I have access to a lot of trees. Mostly oak, some maple, hickory, cedar, and a few other odd tree's. However, right in my yard is a several of the ugliest trees (aesthetically speaking) I can think of, next to pin oak, and I am considering removing one large one for a building. An elm, I believe it to be an american elm, but i'm not the best on identification. Is there any use for elm? Can it be turned, or sawn into planks? I do not believe I have ever seen anything around here made of elm, I searched youtube and found a few projects, but they just say "elm" with no explanation. Just curious what anyone else would do w…
-
-
- 11 replies
- 3.4k views
-
-
Dad and i took a week off to get some logs cut up for some boards. We cut 1400 bf of pine for a friend. Here we did 700 bf for myself. We also did 60 bf of birch and 15 or so spruce 2x6's All in all it was a good week. Got rained out 1 day and goofed off a lil bit. -Jason
-
-
- 11 replies
- 4k views
-
-
A client wants 2 new replacement raised panels for a large old front door on his house. It will be painted on both sides. 20" wide by 24" tall and 1 1/4 thick final dimensions . Door framework is 1 3/4 thick. Been a long time since I did much exterior work. What would be the best wood to handle the full sun and weather without cracking and splitting. It will be fully painted before installation ,held in place by interior trim. Gluing up the blank with Titebond 3 and shaping the panel is easy in my shop, just wondering what kind of wood y'all would pick to make it out of.
-
-
- 4 replies
- 2.9k views
-
-
I am building an occassional table from some lumber my wife's cousin cut me from his property(cherry). I am making the table soley from the 20 or so BF he gave me, so it's tight. The rear apron has a nasty knot that I could not afford to cut out due to limited stock. Can anyone enlighten me on how to epoxy fill it to stabalize it? Is it as simple as pouring it in, letting it set, and then sanding it flush?
-
-
- 5 replies
- 2.8k views
-
-
I'm relatively new to woodworking. My local hardwood store is going out of business and has lumber discounted 35-50%. I wanted to take advantage of this sale, but I'm not sure what I should buy. They have poplar 5/4 & 8/4@ 1.50 bf, walnut 5/4 & 8/4 @ 4.40 bf, cherry 5/4 & 8/4 @ $4.10 bf. all that is s2s. I have about $5-600 to buy up some wood, but since I haven't built much, just a few small tables & shop projects, I'm not sure where my money would be well spent? If you have any advice for me it would be greatly appreciated. They also have other woods - alder, ash, white oak, red oak, and exotics, but those were the main ones I thought about. …
-
-
- 16 replies
- 3.3k views
-
-
Hello there, my 1st post ! im so excited ! My name is Guillaume. I'm a bran new WW in Québec, still learning in school at the moment. I recently had the opportunity to "recycle" a lot of BIG 8 foot long trunks of maple, red oak, and ash. Trees that had been cut last year on the university campus here where i worked this summer. i offered to mill the lumber and recycle it so the students at the school i am at would have nice lumber to work and lear with. Everybody win situation. Was also able to demonstrate the pcocess of milling with a portable mill. anyway, some of these plank are amaaaaaaaaaazing. I have some spalted maple, some amazing red oak planks…
-
- 6 replies
- 6.8k views
-
-
I have never really been attracted to cherry as stock, but my wife's cousin (who cuts trees for a living) showed up the other day with about 40 bf of milled 4/4 cherry. I decided to build an occasional table from the stock, and I really like the way the hand tools worked it. It was a joy to hand plane, much like my favourite wood - walnut. After jointing and planing it to rough dimesnions, I left it to acclimatize for a few days. When I came back to re-mill the last bit to ensure straight/square stock, parts of the wood had dicoloured! I left some smaller pieces on top of some larger pieces, and the area underneath the overlapping pieces was greyish. Has anyone …
-
- 5 replies
- 2.9k views
-
-
Wood drying noobie here. Had a tree sliced up into boards, some 2+ inches, some 1+ inches thick. The stickered stack has been on my covered back patio with pretty good airflow since March 2010. I live in the Portland, Oregon area. The wood has had three full summers of drying time. I am going to move the stack into my shop which is a detached building built on a concrete slab, fully insulated, but only heated when I am in there working.I was thinking of pointing a couple of box fans at it and maybe putting a dehumidifier in there.I don't have a moisture meter. Any thoughts on if I can get this wood down to furniture-type moisture content by patiently waiting it out thi…
-
-
- 12 replies
- 10.7k views
-
-
We're big reclaimers and although we have good methods for removing nails we always seem to miss some. Any reliable and quick ways of detecting metal in the wood besides the handheld wand? Looking for speed and accuracy. Thx.
-
- 0 replies
- 2.3k views
-
-
I'm relatively new to hardwoods other than Oak. I love the color of Maple when finished, and that is why I chose this material to work with next. How hard is Maple to work with compared to Oak? Are there some specifics I should look out for? I plan on buying a brand new table saw blade and jointer blades to ensure my project goes smoothly. But if there is anything else I should do, let me know
-
-
- 39 replies
- 12k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·