Skip to content
View in the app

A better way to browse. Learn more.

Woodworking Forums & Project Advice | Wood Talk Online

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

The Wood Whisperer Guild

Building a Wood Whisperer Guild project? Ask questions about the plans, share your progress, and see how other members approached the same build.

  1. Started by AlexPeel,

    Ok after my rough milling I realized that several of the boards are slightly twisted. I used the second method so I am not sure if I just did not realize there was twist initially or if they twisted after milling. My question is what to do next? I am at 4.5 inches in width on each board and most boards have 1 7/8" thickness so I have some room to play with. I could try re-milling some of the wood but I am not sure what I would end up with size wise, and I dont want to leave myself with no extra to mill off the slab. I have a 12" jointer so I could glue up the slabs and joint and plain them afterwards. They would just be hard to deal with. Should I remill the b…

    • 15 replies
    • 4.6k views
  2. Started by Kevmc,

    I am thinking of using a different wood species for the dog strip to add a little contrast to the bench. I was wondering if anyone else is doing something similar or if you have any ideas/recommendations for what wood would be good. I was thinking purpleheart, Jatoba, Paduk or mahogany. Any issues with these woods or other recommendations. I am aiming to get caught up with the build this week Thanks KC

      • Like
    • 12 replies
    • 3.8k views
  3. Started by bjorn rettig,

    I bought reclaimed floor boards a few months ago and started to clean them up. I hit a bit of motivational problem (I believed I didn't have enough boards long enough for the rear slab - and the shop needed changes, since the boards were so long) but finally started to work on it again last week - after watching the videos on the guild website. Now I have my rear slab done and final dimensioned. Looking good. I will do the front slab in the next few days and should be able to catch up with the videos probably next weekend. It's fun to be in the shop again and the douglas fir looks and smells really nice. Reclaimed Old Growth Douglas Fir. Cleanup cost me 1 tablesaw…

  4. Started by JeffB1,

    Hi guys, My router bit collection is limited what router bits do I need to finish this project size dimensions etc. thanks

  5. Started by mwatkins,

    I'm toying with the idea of either putting the bench on a mobile base or incorporating some casters that can be raised & lowered as neeeded in order to wheel the new bohemoth around my shop. Anyone else contemplating this? Am I crazy?

    • 7 replies
    • 4.4k views
  6. Started by Eric.,

    Just wanted to give everyone a heads up... I ordered the hardware package for the split-top yesterday, and they said it will be about a month before it ships. You have to imagine as more Guilders place their orders the wait will only get longer. So order your stuff! BTW, very prompt and courteous responses from Benchcrafted. I can't wait to start this build!

      • Like
    • 44 replies
    • 12.7k views
  7. Started by sawdusty,

    Well I determined today that I'm in over my head with the work bench project. I thought I would be able to tackle it but it's clearly not the case. I was able to get the lumber for the top from a local yard that had 8/4 skip planed. I thought that would give me ahead start since I don't have a jointer. I've worked on one board all day and what do I have to show for it??? A 97" board that has no intention on being square or flat. 8/4 is just to big for me to handle, I had high hopes, but it looks like I should just stick with the little stuff.

    • 18 replies
    • 5.1k views
  8. Started by dc808,

    I routed out my dog holes with a 3/4" diameter routerbit, therefore the curved portion does not have the called for 1/2" diameter curvature. Is this going to cause a problem, do I need to redo them with a smaller bit or will it be OK to leave them that way? David Smith

  9. Started by Jodavis,

    well after looking at the plans ive rethought my order for wood instead of buying 8/4 ash and jointing and gluing the top and legs together im going to get the top in 2 slabs of ash. so heres my lumber list 1-12" x 5" x 100" slab 1-8.5"x 5" x 100" slab for the 2 top pieces 2-6"x 4" x 100" for the legs 1-10"x 3" x 100" for the vise and end cap and 8- 8" x 8/4 x 100" for the rest i have a sawmill that i deal with that can get most any lumber i need very cheap the ash is going to cost $1.86bf Thoughts?

    • 19 replies
    • 5.1k views
  10. Started by Kevmc,

    I have a question about the 1 5/8 in router bore on the end cap that houses the flange/washer . What is the purpose of that washer and is it critical that the coutnerbore be perfectly sized and flat on the bottom. Mine got a bit mangles on one side so the washer is a bit loose and doesn't always seat perpendicular to the screw for the vise. I trial fit it and it seems to work fine but before I continue I wanted to make sure there are no huge issues anyone sees. I hope I don't have to make another end cap as it fits very nicely.

    • 8 replies
    • 3.7k views
  11. Started by ddh,

    Hi everyone - I'm a relative newbie to woodworking and am thinking about tackling the Roubo build. I'm a little behind the eight ball here, but happy to join to party! There are two main lumber mills here in NH and the cost of 8/4 soft maple is around $4.20bf. Given the the prices that Bell Forest is offering for the build, it seems relatively comparable assuming that they provide decent lumber. Seeing that they work with Marc, I would assume that they offer decent product. Has anyone out there used them as a source for lumber for this build or other projects? They also are offering the option of planed lumber as well as straight line ripped which is a litt…

    • 18 replies
    • 8k views
  12. Started by jgfore,

    I really like the Benchcrafted Tail Vise, but I just can not see paying that much money for one vise. I realize that it is supposed to be very smooth and all, but I had rather make a not-so-smooth vise into a smooth vise by lapping the threads, than to spend that kind on money on the tail vise. I do want it to function just like the benchcrafter tail vise though. Most of the tail vises that I have seen look as though they are made specifically to move the should or end cap instead of moving a dog block. I may have to machine my own parts to make it. If someone has any ideas, I would love to hear them. Remember: I want the dog block to move and not the end cap or should…

    • 2 replies
    • 6.3k views
  13. Started by Kevmc,

    After much work in the evening this week I got all my boards for the top milled up and I am jazzed they came out pretty square and flat Given the length of the boards I am counting that a pretty good success. Maybe this is being overly nitpicky but given the expense of the project it terms of my time and money I wanted to get everyones opinion before I drive on I milled up all my top boards and the width of the rear table with 7 boards is 10 7/8 or 1/4 shy of the plan dimensions. I think I have 2 choices. The easiest is to leave it at that and make the gap stop a 1/4 inch thicker. The other choice is to either get another 8/8 board or mill the smallest board…

  14. Started by AdamAronson,

    Hi all, Been staring at SketchUp ALOT over the past few weeks and I find myself (much to the amusement of my wife) wondering aloud "Am I the only one who prefers end cap option #2?" I really dont see myself removing the end cap to run the bench top slabs through the planer and it seems to me that the enclosed mortise and tenon on #2 might offer a bit more integrity. With that said, I've been monkeying with the SU document to derive the dimensions of end cap #2. Has anyone else done this? Anyone care to give me a reality check? Is my adult onset OCD flaring? "Let's get ready to Rooooubooooooooooooooooo!" Cheers, Adam

      • Like
    • 6 replies
    • 3.9k views
  15. Started by AdamAronson,

    Forgive the newbie-ness - this is my first 'large' build. I'm in the process of milling parts for the base but haven't yet started construction. The top parts and others are still rough. Should I proceed with building the base before milling the parts for the top (next in my order)? I believe I heard Marc suggest this in one of the videos. Thanks! Adam

  16. Started by AdamAronson,

    Hi all, I spent this weekend prepping for and finally getting around to milling some of my lumber. My first struggle is something I figured I'd throw out to the guild as I've never milled lumber for a project this large before. Specifically, when I was milling part "M" - the long lower stretchers I realized that I had no way of jointing these pieces (minus hand tools) because my jointer bed is only 48" long. On both boards the cupping prevented the high spots on the cupped face from touching the jointer bed all atone time. I'd move to hand planes but aside from winding sticks (which I have little actual experience using) I have no flat reference by which to deter…

  17. Started by Chopcat,

    I am planning to add circular dog holes as i get on with the build and as all the drills i can get here are metric I am going to be stuck with 19mm, of which there is not a great choice. What type of bit would you recommend for these deep holes? and any special points to note when doing this. I am hoping that I can get most, if not all done on the drill press. CC

  18. Started by jgfore,

    I am planning on building the Roubo with a few changes. 1st: I am going to pass on the leg vise and go with the Twin Screw. 2nd: I am planning on adding some drawers in the wasted area beneith the top. I would like for someone to tell me if they see any possible problems that I could run into with this design. I left a small gap between the bottom of the top and the top of the drawers so that I could mone any clamps or get to stuff that falls in the gap. I will not be using the deadman with a long holdfast, just small plugs for support. I will also use "push to open" hardware in order to keep the faces of the drawers flush (no exposed handels). I do not want t…

  19. So I posted this in the guild hall which is probably the wrong spot. but I'm not sure how I'm going to procede I'm building my roubo top out of 2 12"x5"x100"ash slabs and I'm not sure about the Tailvise Instalation. Should I just hand mortise the dog holes and cut out the area for the tail vise in the 12 inch slab and if I do Do I still need an end cap? Or is the end grain of the slab not going to be strong enough for the vise? Or just laminate the dog holes on to a narrower slab like the plan says with an end cap? Advice please

    • 6 replies
    • 3.8k views
  20. Started by Shamuss,

    I can't be the only lefty out there. Is anyone else considering relocating the vises to the opposite ends of the bench? Sure, a right-side orientation for the tail vise is perfectly workable for a southpaw, but might it be worth switching for that tiny bit of convenience?

    • 11 replies
    • 4.3k views
  21. Started by woodwhisperer,

    The leg vise installation requires the use of taps. If you aren't familiar, these are special bits used to create threads for bolts. For those that don't already own them, here are some links to the sizes you'll need. Please keep in mind that you can probably find these locally as well. 3/8-16 http://www.amazon.co...ASIN=B000BQW6F0 10-24 http://www.amazon.co...ASIN=B000CFLA3O 5/16-18 http://www.amazon.co...ASIN=B004AUYNVS 1/4-20 http://www.amazon.co...ASIN=B000CFNPGE As an alternative, here's an inexpensive tap and die set that includes all the taps you'll need but DOES NOT include the drill bits: http://www.harborfre...-set-96570.html If you have o…

  22. Started by kaiser,

    I have printed out this template 4 times with no resizing only to have it be a little under scale. Is this normal and is anyone else having this problem. Even when I download the pdf plan v9 and hold my ruler to the computer screen I get the same thing. Top is at 3 7/8" light, 1" squares are at 31/32" and so on. HELP!!!

    • 6 replies
    • 3.4k views
  23. I've never had a split top in a bench before. Other than hanging a dovetail saw in the split, what else do you use the split for? I'm thinking of building the bench as shown in the plans, but I'm trying to figure out if I'd ever use the split. Up to this point I don't think I've ever said "Gee, I wish this bench was split down the center." I'd love to hear from somebody who has the split. How often do you use it? Somebody educate me on the split, please. Thanks, Chet

    • 11 replies
    • 8.3k views
  24. Started by alaporte,

    Marc. Just wondering when the plans will be updated to include the sliding deadman? I'm not at that point just yet but I needed some additional wood and noticed its listed in the cut list but not in the PDF plans. Same goes true for sliders for the Leg Vise Chop. Andy

    • 3 replies
    • 4k views
  25. Started by Kevmc,

    I was wondering what everyones thoughts are in dealing with the uneven floors in the shop area when my workbench will be mos of the time. Should I leave the legs a bit long then trim to make the bench level and stable or keep the legs the same length and shim the bench to be level. If I shim the bench might that risk the bench moving or being less stable ? Thanks

    • 2 replies
    • 5.4k views

Forum Statistics

  • Total Topics 32.1k
  • Total Posts 437.6k

Member Statistics

  • 26,011 Total Members
  • 3,644 Most Online
  • bobtjanitor Newest Member ·

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.