The Shop
1,954 topics in this forum
-
Finally started putting together my new shop. Shed was built by shed people and the electricity Was done by my brother. A big job running all the wires 150' from my house into the shed. Now my turn, floor down, insulation up or almost all up, AC unit went in today and oh what a relief. Next the walls. Can't wait to move my tools in from my basement into the sunlight. Yah but damn by back is killing me... Mike
-
- 8 replies
- 3.2k views
-
-
I bought a nice Lee Nielson chisel, and really haven't got a chance to use it yet, so I thought I'd make a little inset groove for my combo square. It's the tool I use the most on my bench, and it never seems to go in the same place twice. Realize this would have taken 10 seconds with my router, but again, it was chisel practice. Worked out better than I thought for my first time using a chisel. When I finally get around to just making a little hook or shelf for it somewhere else, I'll just square off the groove and flush a pretty scrap cut into it. I actually use the bench for all kinds of test cuts and repairs (mitre keys, inlay, edge banding, chip repair, f…
-
- 0 replies
- 3k views
-
-
Hey guys, Over the past few weeks I have gutted out my 18 x 9 workshop. Beforehand I had a section on one wall which I used to store timber on racks, however I'm thinking of making an area outside to store timbers. Along outside of the long wall, if I was to make some sort of 'porch' to store the timber, would that have any adverse effects on the timber? Has anyone else done this? Thanks in advance ~WW
-
- 2 replies
- 3k views
-
-
Question for those with nice shops: where should the tool racks go with respect to the workbench? On the opposite side from you (bench against wall, you reach over it to get a tool) or behind you (bench out from wall, you turn around to get a tool)? Sent from my iPhone using Tapatalk
-
-
- 20 replies
- 5.4k views
-
-
I know this gets asked a lot and I've looked for answers but I can't find anything consistent. I am thinking of adding 220 to the shop but I don't know if the panel will support it. We have a 200 amp panel and there are no more slots to add any extra circuits. We have two sets of washers and dryers in the house and 2 full size refrigerators. I know that you can get those double breakers that allow you to put 2 circuits in one slot but is there a max number of circuits you should put in a panel. I added it up at one point and the total amperage on the breakers added up to be like 360 or 380 which seems high to me, i don't know if that number even has any relevance. So is i…
-
-
- 15 replies
- 3.7k views
-
-
I was just sitting here looking through some old posts about French Cleats and someone posted a picture of their setup, and I had a realization. The two french cleats I hung in my shop are a different design. I guess I started making them before I knew exactly what type of wood, the thickness, and how they were being secured. I actually have been ripping 2x4s at a 45 and I have been securing them with 4-4 1/2 in screws. They seem to be holding really well, but I think I am going to rehang one in particular that will be holding a pretty heavy cabinet. What do you guys think? I mean they are very solid and I can hang on them. Made a quick awful side view in paint.
-
-
- 7 replies
- 8.5k views
-
-
This will be a first for me, so I am looking for all kids of advise to get started. What I'd like and what I can afford may be two different things, so I look to you guys for some guidance and ideas. I would like to put up a 24x30 structure at the end of my driveway. It will be a dedicated shop/man cave. I live in central jersey and my initial budget is 25k before what I plan to do, which is all the interior finishing including insulating, interior wall finish, heat and electric myself. I basically need to hire out the structure build including slab, siding, roof, a few windows, man door and sliding barn door. I have reached out to Morton buildings to come give me…
-
-
- 30 replies
- 7.9k views
-
-
This should keep the shop much cleaner now!
-
-
- 13 replies
- 3.7k views
-
-
Hoping to order a grizzly g0715p soon, and trying to figure out my electrical situation. I know all of my outlets in the shop are 110. A couple of years ago, we had some electrical work done to run electricity to an outbuilding. At that time, they added a "60 amp feeder line". Being completely ignorant regarding electrical matters, and too lazy to call the electrician to find out, I'm wondering if you guys can tell me if that means I have the capacity for 220, or if that's totally unrelated... Thanks! Terrence
-
-
- 27 replies
- 5.3k views
-
-
My two car garage has been overun by tools. I've got most of the big tools on wheels/mobile bases but I'd like to be able to bring different benches together within the shop to create outfeed tables, assembly benches, etc. The problem is that the garage floor is sloped heavily towards the door. Nothing in the shop is level at this point. I'm wondering if anyone has suggestions for a speedy leveling system for benches that can be adjusted quickly and often. You can imagine that my bench being level prssed up against the side wall is going to be nowhere near the same height (or level) as part of my RAS table extension from the opposite corner of the shop. Are there any tri…
-
-
- 9 replies
- 3.5k views
-
-
I'm having a 30x40 pole built this summer which will be dedicated to my woodworking shop. I'm wondering if I should keep the mobile bases? My planer has one built in and jointer and table are very stable on their bases. My bandsaw is a little wobbly on its and I'll probably put it directly on floor.
-
-
- 16 replies
- 3k views
-
-
My shop vac seems to function by moving the dust and shavings from the floor to the filter. By the time I've cleaned up m shop, the filter is totally packed to the point where the suction is reduced significantly. It is a PITA to have to clean the filter each time I use the vac. The vac is a Rigid 6 hp model, but I have the same problem with a couple of other similar models. I've thought of adding a cyclone to separate the dust from the air, but that adds up to a cumbersome setup that doesn't move around the shop too easily. The idea of a bag tends to get expensive since I do a lot of wood turning and would fill the bag quickly. Any other suggestions?
-
-
- 20 replies
- 5k views
-
-
I haven't had my Grizzly wall mount dust collector hooked up for a few months, and it was finally starting to annoy me. My shop is in pieces right now, and the laziness gets the best of me sometimes, so I left it unhooked. Not wanting to invest in a large cyclone right now for the sake of saving money, I went with a more mobile route, and ordered dust right accessories to help make it easier to hook my one line into each machine as I need it. Before, I had the hose clamp set up which meant I never utilized dc for all my machine operations; again, laziness. I got the 21' expandable hose, quick fit on the hose and the adapters for all my machines with 4" ports. I ordered 3 …
-
-
- 3 replies
- 3.1k views
-
-
So I have been a hybrid type woodworker, but am starting to really appreciate the hand tool methods more and more. I have a frame saw from bad axe on the way, as well as a Stanley 150 miter box saw. I have kits on hand for a shoulder plane (hock) as well as a few blade assemblies, carcass saw kit and sash saw kit from bontz tool works and recently discovered tgiag.com. I will be struggling to deviate from my festool equipment (rotex sander, of 1400 router, ts 75 track saw, older style jigsaw, domino, and Csx drill, as well as ct 26 and mft). Every time I buy a festool product and use it there is a moment of enlightenment, similar to a well sharpened hand plane. So the bur…
-
- 2 replies
- 3k views
-
-
-
Finally after three years of needing to rebuild my skimpy little lumber rack - I DID IT! I used the plans that Mark post over at TWW. Mine goes to 12' high and 12' wide with 6 levels. The top rack is reserved for the light things like trim, molding, etc... The only thing I would change is to use Spax 6" lag screws for the attachments of the uprights to the wall. I loaded the thing up pretty heavily. The rack is solid so I'm not worried about it, but last night I had a vision of the entire wall collapsing. That would really not be fun, but I don't think it's going anywhere. Uprights Up. Chopping plywood into smaller bits. Bracket Supports Buil…
-
- 6 replies
- 3k views
-
-
I am going to build a miter bench kinda like Nahms but I am looking for input on where along the bench to place the miter saw. I have a 12” dual bevel non-sliding saw. If you are facing the wall it would sit on I have 13’ to the right for a bench. To the left I have 10.5’ where I couldn't have any cabinets but could have something that folds out for support as it’s at the end of the out feed if I run 8’ sheet goods on the tablesaw. So I am trying figure out where I should place the Miter Saw. I would also like a spot for my Delta mortising machine, whether it’s permanent or removable like Norm’s. What suggestions do you have? Thanks!!!
-
- 2 replies
- 2.9k views
-
-
I'm slowly getting my garage shop set up & better organized, so I'm trying to get everything off the floor (and often on wheels for flexibility). The clamps just keep getting moved & leaned against the various tools, and they need a better home than that. So I'm trying to decide between wall storage for the clamps or a cart to carry them around. I believe I can sacrifice the floor space, though it would be good to know what else I might use the cart for besides the clamps if I went with that solution. What have you done in your shop & why?
-
-
- 30 replies
- 8.6k views
-
-
Hey all - I'm looking for opinions or suggestions on my shop layout. I'm moving into a new place with an attached 3-car garage, and am turning 2 of the stalls into a shop, roughly 22x30ft with 12ft ceilings. I will put a little half-wall in-between the shop and the parking stall, to give a little more separation and wall space, also a place to put some outlets. I've come up with this setup - the garage doors are on the side of the room without a wall... There is a window by the workbench, and another on the back wall. I mostly have made smaller stuff (coffee table, cutting boards, etc.), with plans for a few bigger things (bed, sofa table). I don't gener…
-
-
- 22 replies
- 5.2k views
-
-
Ok, not woodworking related but still wanted to share ! Over the Winter I installed a beast of an air makeup system to help with fumes and overspray when painting boats in the shop (specifically when it's too cold to open the bay doors for ventilation which happens to be half of the year in Northern Wisconsin). It was quite the process getting the unit upstairs (weights over 1000lbs), getting the air flow correct to match the output of the exhaust fans and hoping like hell it works the way I designed it.. Well, today was the first trial of running everything together.. I'll be spraying the first boat in a couple days which means it's time to clean shop (blow of…
-
- 5 replies
- 3k views
-
-
I am setting up my shop in a basement and would like to control the dust more than I have in the past. Anyone use curtain walls? If so, any special brands out there? I'd like them to run on a track and possible secure to the floor in places. Estimated cost would be appreciated. Thanks!
-
- 9 replies
- 4k views
-
-
SInce I've just cleaned up the garage after finishing my current project, it seemed like a good time to take some photos of the workshop. It's a single-car attached townhouse garage, and about half of it gets used for woodworking - the other half is usually full of bicycles. I was lucky when I moved into the house, the previous owner had had some kind of workshop in there, and the big full-width bench and cabinets at the back were already installed. It's a compact little woodshop, but it seems to meet my needs at the moment.
-
- 13 replies
- 3k views
-
-
Anyone know of mobile bases that can move in all directions? Or alternatively, why i wouldn't want such a thing for a very small space.
-
-
- 5 replies
- 3.2k views
-
-
I picked up a 1000cfm Jet air filtration unit and I am wondering about the importance of positioning it in my shop space. My shop space is pretty darn small (10' x 30' with 8' ceilings) so the 1000CFM is about 3 times what I need. Power tool use all happens on one side of the space (a 10'x15' area) the rest of the space is mostly storage. I've read that I should put it along one of the long walls, preferably with the exhaust pointing towards me most of the time. How crucial is the intake positioning? Is there a material difference between mounting it on the wall vs on the ceiling as long as it is high up?
-
- 4 replies
- 3.1k views
-
-
I might be buying a house from my brother. It has two possible spaces for a shop. The garage and the basement. The garage needs a new roof as it leaks badly, needs insulation, new panels put up on the walls, electrical, lighting, second box to stretch out the power and increase the circuits. The garage is only a one car garage. The basement needs lighting, second box, electrical walls need to sealed to prevent moisture. and it is much larger then the garage it's the size of the house. Just one large room with a furnace and water heater in the middle of the room. Large enough I could have a spray booth down there. My concern is for moisture with the tools and ca…
-
- 25 replies
- 6.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·