The Shop
1,954 topics in this forum
-
I just installed new radiant heat panels from Solid State Heating. Sent them the dimensions of my shop and the insulation. They recommended two of the 2'x8' Wood Shop panels. I have them installed them according to the supplied diagrams. Now all I have to do is wait for fall and winter. Has any body else tried some thing like? If so how did it work?
-
-
- 15 replies
- 5.1k views
-
-
Reclaimed redwood, very soft, very fine dust - two problems. 1) It's impossible to collect. The bags on the collectors fill up but it's still all over the shop. I am having particular trouble with the jointer and tablesaw. 2) The dust is so fine it has ruined the action on a new Jet SCMS. Is there any way to prevent fine dust from getting into the hydraulic/bearing assembly? Also, is it safe to wear a paint respirator for dust? Thank you in advance for any suggestions.
-
-
- 2 replies
- 3k views
-
-
Amazing how much time goes by in my life between working and having time to work in the shop.... Its September now and I last did work in the shop in April! I guess I can call it reflection time! Anyways I need some ideas and your thoughts as I continue to clean and set up shop proper. Here are some photos of where I am to date: The thing I am currently debating is the wall of cabinetry. I will not have any other wall space in the garage, it is pretty much all spoken for and I am starting to wonder if I should make such a big commitment to cabinetry.... The wall opposite the garage doors is pretty much spoken for between a "garage" metal rack that is for …
-
-
- 46 replies
- 10.8k views
-
-
My woodshop has always been in the garage and for anyone who knows how cold it gets in Northern Minnesota... it pretty much sucks to work out there in the winter.... Finally talked my wife into letting me use the backside of the basement (which ends up being a bit bigger than my garage anyways) Garage was 8x12 (single stall) basements is 12x15 so I get a bit more room... I just started moving stuff down there last weekend but have a ton to go but I thought I would put a couple pictures up of what I have to work with... Still need to get the assembly table down there which also acts as my out feed table for the table saw and the 1 bench I have down there alre…
-
- 26 replies
- 7.2k views
-
-
Here are some pictures of my 36x36 stand alone woodshop. this is looking in from outside the overhead door
-
-
- 10 replies
- 4k views
-
-
The attic of my shop is an unfinished space that is 30' long by 12' wide. I'm in desperate need of a finishing space so I'm seriously considering erecting a wall across the space to make a 12' x 12' finishing room on the far end. It's less than optimum because I have to carry projects up the stairs to finish them and it's not climate controlled (yet), but it's my only option so it will just have to do. There is a window on that end of the attic that will allow me to exhaust overspray. I'm just beginning to formulate my plan and I would love to hear any lessons learned you guys have or pointers to online resources relevant to this subject. This will be done on a shoestrin…
-
-
- 23 replies
- 11.5k views
-
-
Has anyone on here built or used Norms router table? Was looking for plans for a table and found this website. http://www.crestonwood.com/router.php. Looks functional and reasonably easy to build. Was thinking originally about putting it on wing of table saw but I think that would be a hassle. I have not used a router table so I really have no idea what to look for in the design. I would love some input. Planning to build this and some new shop cabinets in the hopefully near future. Particle Board already offer to help with sketch up on the cabinets but need to figure out plans for the router table. Would love some input.
-
- 9 replies
- 6.2k views
-
-
ok guys here is my 7x10 turning shed I have talked about it a few places and someone asked what it ended looking like. I have insulated the walls and roof. and put my lathe in there. when I moved in there was a old rusted shelf that im putting to work and a rough work bench that I mounted my grinder too and use for a table. I have enough room to take about two steps in any direction hope to get a better stand someday
-
- 4 replies
- 3k views
-
-
Like most woodworkers, my shop started small. My first one was one-half of a one car garage. Over the years shops came and went, growing larger each time. We recently moved from FL to southwest NM. Everything in the shop made the move, including a couple of dozen shop cabinets I custom built over the last 25 years. The new shop is an inexpensive steel building 36x60. The building is divided into three rooms and the shop part is 36x36. Although the shop has heat and air, we insulated it so well that the shop is usually quite comfortable year round. The machinery is nothing special - mostly Grizzly except for an old Powermatic table saw purchased used. I went for …
-
- 8 replies
- 3.9k views
-
-
Getting into a new detached two stall shop. Really excited about laying it out and setting it up for a long duration in the shop. I want to do it right from the get go. My questions, is it worth it to frame and insulate the slab (x"? foam insulation) to help make the space warmer... 2x4's flat 16" on center? rigid foam in cavities? Floating? Screwed to concrete? Tongue and groove plywood? no T&G? Thoughts? Is there any good videos or tutorials out there?
-
- 9 replies
- 2.9k views
-
-
So I am in the process of setting up my first real woodshop. I have the lucky fortune to have plenty of space to work with thanks to my family farm. I have put down a new floor, built a bunch of lumber drying racks (currently I have a good 1500 of board ft of Red Oak, White Oak, Walnut, Maple and Apple air drying). I am working on electrical and dust collection now. I have 2 2hp reliant dust collectors and 1 1hp grizzly dust collector. My plan is to set them up on the floor below with switches to turn them on and off and blast gates to isolate the tool. so here are the questions: 1- is going down the best option? Most people go up, is that because its safer/be…
-
-
- 19 replies
- 4.1k views
-
-
Not a question just a shop score! Traded a project I built for some electrical work from my electrician friend. Got a bunch of nice overhead lights for free so I am going to get more light and more circuits at no charge. I am in serious need of both! While I would love to have more room, I must say my small section of garage shop is coming along nicely! Sent from my iPad using Tapatalk - now Free
-
- 6 replies
- 3k views
-
-
Good afternoon, We just signed the papers for our new house... close december 6th. New home has a 2 stall detached shop that will be dedicated for my woodworking. I am planning on putting in a heating source (live in ND)... I am a big fan of using the scap wood for heat as well as eventually get my own pellet mill and create my own pellets from sawdust... grass clippings and leaves...Here are my thought options... 1. Gas heater. - can set it up with a thermostat and can keep it warm all the time 2. Wood Stove and gas heater - base load with the wood stove and still have the thermostat of the gas stove 3. Pellet stove and gas heater - thermosta…
-
-
- 9 replies
- 4k views
-
-
Marc and Anybody With Similar Experience, You've had quite a bit of experience with both the Oneida DC and now the ClearVue DC. I realize that the ducting for the CV is probably better/more efficient than what you had for the Oneida but can you adjust for that difference and give us your opinion on the two systems? Bottom line, starting from scratch, assuming the same shop layout, same Nordfab ducting and if money were not a factor which system would you choose and why? I've read through Bill Pentz's website and talked to him and he really has a compelling story. For my small shop DC I am leaning strongly toward the CV/Norfab option but I think it is always a good…
-
-
- 6 replies
- 18.5k views
-
-
Guys, I'm redesigning my tiny workshop (10' x 12') and I'm looking for ideas. The only big-ish piece of equipment I own at the moment is my 6" 4ft jointer which sits on a mobile base. Everything else is small and portable. I'm planning to center my workshop around a work table slash bench. It will be a torsion-box based 3.5'x5' bench with two beefier adjacent edges so I could drill some dog holes it them and attach a vice. I also want the bench to mate with the table saw (is there THE standard hight for TSs?) and include storage for my shop vac, planer, track saw, etc. Ideally, I'd like to be able to break the bench apart and move outside when I need to work on bigger…
-
-
- 15 replies
- 4.6k views
-
-
Why not! My contractor saw is awaiting pulleys and a new belt to tame the vibration. God, I hope that works otherwise I wasted a bunch of time and money not only on the belt/pulleys but on building a saw station... we'll see. My benchtop saw is a ryobi bt3100 similar to some craftsman line saws. The rails are extruded aluminum, with channels in the underside and rear faces that accept a flat oblong rectangular metal plate that is threaded to accept a stud. The saw had the option of converting to a wide kit by using this plate to join two rails together to allow crosscutting wide panels. My woodworking marathon day started with the need to breakdown some panels for…
-
-
- 2 replies
- 3.5k views
-
-
Hi everyone first time here been loving the pod cast so i figured lets turn here. quick run down... Been wanting to build a shop for years and due to one thing or another it always got put off. Well I said the hell with it and sold my record collection and guitar pick collection and now have the money to buy some of the bigger machinery. So then while shopping at work I have a stroke ...I know the hold worlds against me hahaha. but the reason I mention is this, I can not lift a huge amount any more but I have 2 other strong guys that can help.... BUT my questions is this.. My shop is going into a walk out ranch over grass about 30 -40 feet how is the best way or h…
-
-
- 12 replies
- 3k views
-
-
I am finally embracing the fact that I should probably have a web capable piece of equipment in my shop. The magic question of course, is what do you all recommend. I have a good dust collection system, except for when sanding. I have an air filter system, but finding "fines" settled on all the surfaces after an afternoon of sanding is not unusual. I didn't see a good thread on WTFs about this topic, but please reroute me if I simply missed it. Laptop vs Tablet? I do use SketchUp, especially for commissioned works. I would love to at least be able to view / explode sketches from the device, and bust out the measuring tool. I am tire of spending a lot of t…
-
-
- 32 replies
- 7.6k views
-
-
I recently after much waiting finally got a bandsaw. The model is a Bernardo HS 350 N (14 inch ). I ran threw all the steps of setting it up....but have hot some major issues when it comes to re-sawing... I have tried and tried to adjust the drift using the fence without success.... it keeps making a non linear cut. giving up on the fence i decided that if the blade is 90 degrees to the table (which it is) then i would just score a line on the piece i want to re-saw and do it free hand. i though this would work....but no.... when i cut following the line i score on the top of the piece i'm re-sawing it looks like the cut is going fine , nice and s…
-
-
- 8 replies
- 3k views
-
-
Hey gang, I'm looking to build a "perfectly" flat assembly table that will also serve as a large out feed table for my tablesaw. I've been considering building the torsion box Marc built but I have a pool table that I want to get rid of and I suddenly thought what could be flatter? I think it is about 1 inch thick slate. Does anyone have any ideas on how to go about building this or has anyone ever heard of using slate for this purpose. Any suggestions would be welcome.
-
- 10 replies
- 11.1k views
-
-
PM1900 Dust Collector – Collector Bag Leaking I have a Powermatic PM1900 and both collector bags are leaking fine dust. Is anyone else having this problem? The unit is equipped with canister filters on top and collection bags on the bottom which are heavy clear plastic. There are no holes in the bags and I have installed them multiple times to ensure they are on correctly. PM technical support did not have any ideas other than to install the bags according to the manual. I must be doing something wrong installing the bags or these units leak fine dust by design. I can see traces of dust leaking where the bags are secured to the steel housing by the fabric covered spring …
-
-
- 2 replies
- 3.5k views
-
-
Do u guys think Krenov sawhorses could be built and hold up with construction grade lumber? I have searched the internet and found no examples. I need to build another set of sawhorses and these look fun to build. Could practice some joinery too. I have a bunch of 2x construction Lumber that I want to use. The lumber is 50+ year old 2x10's. I don't think it will move much. Thoughts? Sent from my iPad using Tapatalk - now Free
-
-
- 14 replies
- 6.8k views
-
-
My shops new cabinets are all modular and on casters. This allows me to transport them from Redondo Beach to Colorado easily. Also being able to move them around helps me clear spaces. Today is the time to make my handtools cabinet. I am using some old 3/4" marine plywood I had laying around. It is not about being pretty, it is around flexibility for the moment. I am thinking of just building a cabinet with drawers.
-
-
- 2 replies
- 2.9k views
-
-
So I am just getting started at setting up shop in my new house and was hoping for some input on my options for the ceiling. As the title says it is a basement shop. The new dimensions are going to be about 33'x12'. It is a walkout basement so will include a nice big window and an small overhead door. The floor joists are at two heights (sunken living room above), taller is 94", shorter is 86"(?). Rest of the basement has drop ceiling and I need to keep some way to access the stuff in the ceiling of the shop (pipes, wires etc). I can't do drop ceiling in the shorter part due to the overhead door, and don't want to lose the height. Walls in the shop are going t…
-
-
- 11 replies
- 3.7k views
-
-
I know there have been many discussions on the need and performance of air cleaner/purifiers. However, I believe that it will help clean the air in my shop. My plan is to build my unit using a squirrel cage fan from a Jenn-Air kitchen fan, installed in a 16"x16"x20" box. I plan is to us 2 layers of 1" semi quality pre-filters which will slide into dados in the box. My question is, what do you all think about instead of using an expensive hepa filter as my final filter, to rig up a bracket on the end of the squirrel cate fan? I would then use a piece of all-thread screwed into the bracket and install a shop vac type hepa filter onto the all-thread, thus reducing my co…
-
-
- 11 replies
- 3.7k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·