The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
When I stacked my recent walnut haul, I couldn't find my jug of anchorseal so I grabbed two cans of latex spray paint. I painted the ends with a generous coat, twice. I'm noticing very small checks starting. Under 1/2"long. When sealing the ends, I was thinking you just wanted to slow loss, not seal it completely. Two coats made a decent barrier I thought. Should the ends be totally sealed off?
-
- 7 replies
- 3.8k views
-
-
The house across the street from me is getting renovated.I was able to get my hands on two of the interior doors.Under the many layers of paint is clear mostly Vg fir.One of my favorite woods.The best piece has about 45 lines per inch. Nothing long enough to make table legs so boxes it will be. Not to bad for free wood. my lucky day
-
-
- 19 replies
- 3k views
-
-
About to embark on a new build (bedroom table), and I'm costing out lumber. I want walnut, but the price is ridiculous. It will literally cost me twice as much as 90/50 cherry. I love cherry, and have been building a lot with it, but its certainly not as nice as walnut. 90/50 cherry goes for $4.83 BF (4/4) and $5.89 BF (8/4). Walnut it $8.99 BF(4/4) and $10.99 BF (8/4). Just kinda thinking out loud here. Any comments or opinions? The room is in a new house, so no existing furniture to match. Trim work is solid wood, but painted out white, so it will go with everything.
-
-
- 28 replies
- 5.5k views
- 1 follower
-
-
I recently purchased a good amount of cherry lumber that was rough cut. Most of the boards are at least 6 inches wide, some being 10 or more. My jointer is only 6 inches. I watched the planer sled (with router on tracks) to mill wider slabs and was wondering if I can use that same I'd a for my wife boards that are currently 4/4 thick instead of cutting them down to fit on jointer. My planer is good for 13". I'll still cut boards down to join them up I just figured it would be less waste. Any help is appreciated! Thanks!
-
-
- 11 replies
- 3.8k views
- 1 follower
-
-
Looking for some advice. This past weekend I milled some 4/4 walnut that I've had for about a year down to 3/4. Got them all nice and flat. I edge glued two boards together and clamped them for about 12 hours. For a total of four boards. All four were done gluing by Monday afternoon. Today I went out to start sanding when I saw that all four have cupped. I live in Martinsburg, WV, and yesterday we had a front move in. Over the weekend we had nice warm sunny days. Today it's been cool and cloudy with slight rain. My shop is in our garage with no AC or heat. Could this cupping being caused by the weather?
-
Bit of a noob on slabs, so I am hoping you guys can tell me why this will fail. I have a dried cedar slab, 2 inch thick, 14 inches wide, around 7ish feet long at this point. I want to use it as an outdoor bar/leaning rail/ place to put your beer. If I mount it to a single pillar in the middle (attached to structure of the deck at the bottom) how bad will this thing warp on me. Anything I can do to prevent that by supporting underneath? It's in a tight spot and will be directly against the house I think its also pretty narrow for a full table structure underneath since I want it ~40 inches high. Thanks again .
-
- 16 replies
- 3k views
-
-
What is the opinion of the forum as to the best way to make strong miter joints in plywood? I plan to use spines to add surface area for the glue and to add an accent. Do biscuits work well in plywood? or is there another method that I'm not familiar with?
-
-
- 9 replies
- 6.4k views
-
-
Ok. I've been noticing this for quite a while now, and wanted to check with the experts to see if I'm off base before I call my lumber yard. First a question: The measuring sticks they use at the yard, should they come up with a different board feet measurement than if you measured both width and length with a tape measure? Outside of normal rounding differences? I've noticed pretty consistently that it seems the employees at the lumber yard are getting a higher BF quantity than my calculations when I'm picking out the lumber. I can only wonder if those sticks they use to measure the width are working off a different calculation than I'm working with, thus cau…
-
-
- 52 replies
- 13.7k views
-
-
Anybody have experience with kiln dried Cypress? Client wants outdoor table in Cypress. Salesman at lumber yard mentioned that kiln dried cypress is more likely to weather.
-
-
- 4 replies
- 2.7k views
-
-
I have about 2000 bd ft of lumber sitting in logs right now. The only portable mill I could find quoted 75hr. Anyone have experience with portable mills and how much they charge? The only reason I am considering a portable mill is because my usual mill takes about a year to get any lumber back from. Thanks.
-
- 14 replies
- 3.5k views
-
-
I'm heading to pick up 240 BF of white oak for $199 bucks. All 8/4. 11" wide x 11' long and 7 1/2" wide x 11' long.
-
-
- 24 replies
- 3.5k views
-
-
I just bought a chunk about the size of a normal red brick of spalted maple off ebay. It's freshly cut and wet to the touch. It's starting to grow a little mold. I know I need to dry it out somewhat quickly to get the mold stopped and to prevent the spalting fungus from softening the wood further. The wood is so spalted and figured I can't identify a face grain and end grain side to figure out which is the end grain to coat it with wax. Should I coat the whole thing in wax? Just let it air dry as-is? Try to microwave dry it? What do you think?
-
-
- 22 replies
- 4.6k views
-
-
I got hooked up with a local guy who owns a band mill and has been milling some interesting domestic trees. I ended up buying about 42 BF of chokecherry off of him as well as roughly 50 BF of green ash (I think). I also bought a small piece of Russian olive, just to see what would happen to it when finish hit it. The chokecherry is all from the same log so i can book match some of it to make a top for the entertainment stand that I'm planning on making. I just bought the green ash because it was ash and it was $1 / BF. He did mention that the ash was intentionally quarter sawn. I'm not really too sure why he did that, it looks the same as flat sawn ash. …
-
-
- 20 replies
- 3.2k views
- 1 follower
-
-
Drawerbox sides, backs, and bottoms are usually made of what we call secondary wood. Something less expensive than that out front. But we want a species that can machine well and be cut with hand tools well, and has enough dimensional stability for the job, plus durability for the service. In kitchen cabinets, the industry promotes northern hard maple as the premium species for this. Dialing things down in cost, there is soft maple, red oak, and poplar. What do you like to use?
-
-
- 14 replies
- 3k views
-
-
I've managed to a bunch (<100) of smallish assorted wood veneer pieces and I'm considering the best way to store them. The pieces range in size between 8x8 and 24x24 I don't have a lot of space so I need efficient but quality storage ideas that preserve the veneers until they are ready to be used. Any thoughts about storing in plastic storage containers like the type you could use to store extra clothing under a bed, etc.? Perhaps with a piece of MDF or ply at the bottom of the box and another piece on top to keep things as flat as possible? Any problems with this?
-
- 4 replies
- 2.7k views
-
-
I was touring a friends saw mill yesterday, who imports exotics for a living, and he was showing me newly milled lumber. This is what they had just sawed: 8/4 cocobolo slabs with the most beautiful colors a figure I have ever seen. These slabs area 7 feet long and 13.5 inches wide each. Dummy that I am, I committed to buying all three. Now I have to come up with a design(s) that does justice to these slabs.
-
-
- 73 replies
- 14.1k views
-
-
I have a beautiful piece of cherry with a live edge. It is air dried and I'm working on making a table out of it. My question is in regard to the bark on the edges. I have knocked off all the loose stuff, but there is still quite a bit on there. It is a crotch piece so there is a lot of contour to the piece, getting all the bark off would be very difficult getting into all those nooks and crannies. If I leave it on am I asking for trouble down the line, or if it seems very firm should I be OK? Thanks for any info. I could post a pic if that would be helpful
-
-
- 11 replies
- 3.2k views
- 1 follower
-
-
... but piling it up instead. So far, after 2 years of on-and-off cutting and building I've created 4 "stacks" of wood. The first is the long strips and board pieces, 2-6 ft long, that come off the sides of ripped pieces, or perhaps halves of longer pieces. The second is square blocks that come off the ends of boards. The third is short strips, usually narrow, about 2 ft long. Finally there's a steel trash can that holds the normally usuable pieces -- damaged ends, triangles, and such. (I don't inventory any wood but instead purchase it as needed.) Next step, probably Saturday, is to parse out what really ought go in the trash. (Sawdust, of course, goes in…
-
- 12 replies
- 3.1k views
-
-
These had cracked paint on them so thick that it looked like the hardware on it was mortised into the wood. I scraped them, taking a full days work each for one side, with a heat gun, and Red Devil flooring scraper. Finish is Epipanes applied to directions. We weren't planning to varnish them to start with. The panels had shrunken enough so one had a gap all along one side of its panel. I had to get the paint off, so I could center the panel back. After getting the paint off, no way were we going to paint it, so I stripped the rest of both of them. The panels are 15" wide. There was beaver fur around the panels in the grooves for weatherstipping. It may …
-
-
- 13 replies
- 3.2k views
-
-
I was thinking about a guy's post a month or so ago, how he started making dovetails beginning with soft wood instead of hard. From what I've modestly experienced, it would seem that working with a harder wood -- like a maple -- might be easier for learning on than a softer wood -- like pine, poplar, or cottonwood. :-) (Does anyone work cottonwood? Just threw that one in.) That said, it was noted the other day that zebra wood is apparently difficult to joint. How does one smooth its face? Sander + scraper? I saw a chunk of it over at WoodWerks the other day and though it might make a really beautiful camera piece.
-
- 6 replies
- 3k views
-
-
Anyone worked with pin oak? Thoughts? A guy called me up, he has 24 foot long pin oak log, 12 inches thick at it's thinnest, 18 at the thickest. I said, sure no prob. I mean, should be interesting. Got a couple of guys local that can cut it up for me. And can store out in my parents machine shed while it dries.
-
-
- 33 replies
- 6.9k views
-
-
A buddy got his hands on a short walnut log that measured 13" across and about 6' long. There was no visible rot so I accepted it when he offered it to me. I don't have a lathe yet but figured I would cut it up into 10" sections for bowls once I do get one. I took the chainsaw to it and cut two sections down and was quite displeased to Find a few termite burrows and one live wriggler right where the heartwood and sap wood meet. Are these even worth keeping and treating with something? Any way to kill em all off and salvage?
-
- 10 replies
- 3.2k views
-
-
Making my first trip to the lumber yard tomorrow. I've watched a few videos and have done a little research, but I'm sure I will look clueless in there…learning experience. I understand 1 BF = 144 cubic inches and know the difference in 8/4 6/4 etc questions I do have… 1) What is the smallest piece lumber yards typically sale? I want to make a cutting board so don't need a ton of material. 2) Most prices online have several different prices for the same wood i.e. Iroko cost $9.74 bf (1-99), $8.77 (100-999), $8.28 (1000+). I'm guess that has to do with a) the quality of the lumber and 2nd guess b ) quantity of lumber. Gut is going with "a". If i am correct w…
-
-
- 17 replies
- 3.7k views
-
-
The yin to WTN's yang http://www.woodtalkonline.com/index.php?/topic/20788-Does-it-get-any-better%3F Red oak. Not allowed in my shop. Worse smell ever.
-
-
- 34 replies
- 6.1k views
-
-
Hello. I do some wood carving and wood working mostly having to do with black powder firearms. Normally I get a stock blank with a gun kit or i order a blank for whatever I'm doing. However this time I'm building a "fantasy" cap&Ball revolver. Which means a gun that is not historically accurate but could have possibly existed as a custom gun in that time period. So my idea for this project requires me to make a black walnut grip. No problem there, Inletting the frame and shaping the handle is not going to be an issue. I also want to inlet a silver Star like on a Texas Confederate Dance Revolver. I think it will look good in the Black walnut but might leave it out d…
-
-
- 9 replies
- 3k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·