The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
I received a large old beam from my mother in law a few years ago and had it sliced up last weekend. I was hoping someone might be able to offer some insight as to what would it might be. The beam was about 10' long, 13" wide, and 4" thick, I assume it was meant as a joist or support of some sort, but the lack of nail holes or anything makes me think it was never actually used. She doesn't remember where my late father in law got the wood but it was somewhere in middle Tennessee. If more pictures would help just let me know.
-
-
- 28 replies
- 5.6k views
-
-
I got this from a good friend who attended an auction a few days ago. Gave him $6. /bf for the whole lot. 90 bf of Honduran Mahogany and 150 bf of Walnut. The mahogany is all 5/4 and the Walnut is a mix of 5/4 and 8/4. I know I'm gonna catch heat for having that much Walnut.....but daddy didn't raise no fool either. Sorry about the poor lighting, but the finish room ain't finished. I wound up cutting most of the mahogany in half, most were 18 feet. 16' tape! There were a couple even wider. This is just to show how pretty it is....
-
-
- 28 replies
- 5.9k views
-
-
Pulled off a cabinet door to test paint on it (milk paint.) Noticed that there is a seam. A bad one. The door was not the same size as others so they glued two together, they left a lip on top and bottom, because they are not vertically aligned if that makes sense. They were super heavy, I thought they were pine before lifting it. So I sanded through the finish and wet down the grain. Here are the pics, I feel like I know what they are. But kinda looking for confirmation. Thanks for the thoughts.
-
- 3 replies
- 2.2k views
-
-
okay first post, sorry if this has been asked, but Peruvian walnut? how different than Black walnut as far as milling, grain pattern, etc.. reasonable alternative? BL walnut i have looked at i would put in firepit, full of knots and twisted/cupped really bad. price is close
-
-
- 10 replies
- 3.6k views
-
-
Hello all. This is my first post on this forum, and I could use some advice. A brief(ish) backstory....I purchased a 198" X 17" X 4" Redwood Live Edge Slab about a month ago that I'm using for my mantel. When I got it, the weather had been Clear/Sunny so I left it outside on 1 foot long 4x4 blocks, in my driveway for more room to work on it. After no rain for about 20+ days(Northern CA), I thought it would be fine. When it did start raining, i covered it with a tarp (which that idea failed) for about a week expecting to move it into my garage the following weekend, which turned into another week after my daughter broker her leg. That brings us to present day.... My wi…
-
-
- 5 replies
- 2.9k views
-
-
I was at Austin Hardwoods (Denver) this morning to get a little cherry. Am always amazed by the specials and slab stock on the floor in the sales office. There were other slabs. Some clear wide cherry, a stack of wormy maple, and a set of gorgeous white oak, all bark-on in log sequence, but the best was this stack of two slabs of monkeypod. Size is about 40" wide by 118" long. Get out your checkbook. One will probably get selected by Peyton Manning's furniture guy for use in making a reloading bench.
-
-
- 17 replies
- 3.8k views
-
-
I'm working on a design for a set of low back bar stools. I mocked up the front and rear legs in ply, refined a shape that pleases me and went to Hd to get some 2" poplar. News to me, they only sell 3/4". I really want to prototype a chair with 4 legs, seat and back rest. Get the joinery figured out, ensure a full sized chair looks right before butchering good wood. My local hw dealer sells alder for $2/bf. Ive never worked alder before but think it's pretty soft. Is it a viable option for a working mock up?
-
-
- 16 replies
- 2.6k views
-
-
Made my crosscut jig a couple of years ago out of 3/4 big box store plywood. I noticed some problems with it suddenly and started investigating. I found voids, some long enough to see through, and separated lamination despite predrilling screw holes. I am now on hold at the shop until I can get over and buy a sheet of 3/4 baltic birch. Jeff in KC
-
- 7 replies
- 3.6k views
-
-
I picked up the lumber for my knockdown Nicholson workbench today. Im using 2x12 SYP. When I got them home I checked the MC and they range from 7 to 8.5. I have another 2x12 board in my shed that I'm also using in the project. It's been in the shop since last summer so I'm using it to judge the equilibrium value for the shed. That board is around 10.5%. Is the difference between the new lumber and the equilibrium value too great to start working on the bench? Sent from my iPad using Tapatalk
-
-
- 5 replies
- 2.6k views
-
-
I'm currently making some entrance gates for both driveways to the castle and chose Iroko which has some characteristics of Teak. It is really durable, doesn't move much in service and is both rot and insect resistant. It is a heavy wood so am using it for the frame of each gate. Then I am using Western Red Cedar tongue and groove boards to clad the faces. I was milling the Iroko the other day on the jointer and left it in the shop a few days to acclimatize after milling. There was little movement after machining but I did have to break out the jointer plane to true a couple of edges. Wow what a fantastic timber to plane by hand! Continuous shavings from most parts o…
-
-
- 7 replies
- 3.7k views
- 1 follower
-
-
Has anyone ever worked with elm. We cut an elm tree down that needed removed and from a large fork to the base I noticed a large darker kind of reddish middle in the log. So I saved that part of the log for getting sawed up. Ended up with 8ft and a 5ft logs. Curious if any has ever used elm I figure there is a reason I don't so anything built with it. I did notice it was very wet and figured I'd let it dry in log form for awhile before I get it sawed.
-
- 4 replies
- 2.4k views
-
-
I am getting ready to build a G&G blanket chest and am planning on using some form of mahogany. The "genuine"/Honduran variety is quite expensive and I was thinking of using African mahogany or sapele. I really do not want to stain or dye the wood and was wondering if either of those alternative species would yield anything close to the natural color change that a genuine mahogany does (darkening to a reddish-brown or dark brown). I'm in no rush for the color change, so whether it is 3 months or 3 years (or longer), it doesn't matter. This is going to start out as a toy box for my son and then ultimately, he'll have a nice chest to use as he gets older. So, seein…
-
-
- 3 replies
- 6k views
-
-
Hi all, I've had a tough time finding the hardwood I wanted for the Roubo build. I just couldn't shell out $800 for wood cut at the wrong dimensions at a place far away that would require me to rend a uhaul on top of the cost of the wood... Ugh. So, I found a guy who sold me lots of beautiful red oak for $2 / bf. It's fresh, though. So now I have to wait or to find (or build) a kiln. Ugh again. Living in North Mississippi is rough for this would-be woodworker. Any advice on buy, drying, kilning, finding a kiln-dryer person, etc.? The most feasible solution I've found is this one: http://www.instructables.com/id/Kiln-Dry-Lumber-At-Home/. I don't want to ruin hun…
-
-
- 8 replies
- 3.1k views
-
-
I am going to go look at some hard maple today, and possible buy some. This will be for a new work bench top. Split top style roubo. My question is what most people pay per BF for hard maple? I know price will very based on area and what not. I am just looking for a ruff estimate . The stuff I am going to look at is 8/4 thick, and 5-6" wide. Shortest boards being 7' long. I also have a few sites up on the phone for identifying between hard and soft maple. I will be using the visual way, as not making the color test not able to weight it. Also any advice anyone has on buying hard maple for a bench would be great. I know to stay away from defec…
-
-
- 22 replies
- 3.6k views
-
-
Going to build some built-in book cases, and need to choose some paint grade plywood. I am a bit confused about the paint grade selections at my local lumberyard. I have two options that I am considering - a D3 domestic plywood (maple) and a C2 import birch. Here is where it gets confusing. The C2 birch is 18 mm, made from 11 plies, and is $10 cheaper per sheet than the domestic D3, which is made up of only 5 plies. Why would the material labeled as higher grade, with more plies, be less expensive?
-
-
- 9 replies
- 2.8k views
-
-
I recently picked up about 300 bf of select cypress. It is mostly 4 to 6 inches wide and 4/4 kiln dried and straight line ripped. I was able to get the whole lot for $1.50 a bf and now I am searching for some justification. My wife would like some Adirondack chairs and possibly some other outdoor furniture. Was this a good buy or did I just get too excited at the lumber yard again?
-
- 3 replies
- 2.3k views
-
-
Found a good source for maple. Got an old Polaroid MP-3 copy system at an auction for <$5. And still flat given its original purpose. Of course it may not be in perfect condition, but at the price ... The base is maple, about 20" x 30". I'm thinking a router table top, maybe. (I suspect there are other good sources for wood like this from other industries. But photography is my venue so I thought passing on the idea might be helpful. They show up frequently at auctions. If you get one and it still has the lens, those sell on eBay or CL for $10 to $50 depending on condition. You can pay for your wood right away and maybe gain a little pocket money to boot…
-
- 2 replies
- 2.2k views
-
-
I live in Northwest Arkansas, and I am having a really hard time finding good sources of hardwood. Maybe I just don't know how to look. I search lumber mill and sawmill and am just not finding any good leads close by. The question is this: Is there a good online source for finding lumber mills and hardwood supply houses? Does anyone happen to know a good one in my vicinity (SW Missouri, NE Oklahoma, SE Kansas, NW Arkansas)? Thanks for any help I can get...
-
-
- 33 replies
- 17.1k views
-
-
-
This is kind of a fun one... a friend in Australia needs a new boss for his boat's steering wheel (photo below if, like me, you don't know steering wheel anatomy). He sent a diagram with dimensions (in metric - yikes!) and I'm pretty confident I can make it... the only question is "what wood?" In 8+/4 wood in the shop, I currently have sugar maple, walnut and purpleheart... do you think any of those would work? Or should I got for something more "nautical" like teak?
-
-
- 12 replies
- 3.1k views
-
-
I'm not sure what to call the dark brown spots but they certainly make for a couple of unusual pieces of cherry. I haven't decided if I like the look but I think on the right project they might look pretty cool. Just thought I'd share....
-
-
- 10 replies
- 2.9k views
- 1 follower
-
-
Two weeks ago I received a shipment of old-growth, river-salvaged H. Mahogany from Greener Lumber, LLC. These boards are all from the same log. In 2012 I had received two planks from this log. [See image of computer desk made from one of them.] Now the family is reunited. Wonderful ribboned and other figuring. Rough sawn to 1-1/8 inch thick this stock is heavier and tougher than typical Mahogany. I've begun work on a cabinet as the next build with this awesome material. The cabinet will be used to safely store my prized THE BOOK OF PLATES published by Lost Art Press. A while ago Rich (of Greener Lumber) posted a short gallery bio and pix of projects I've created using his…
-
-
- 6 replies
- 4.3k views
-
-
Hey guys new to the forum. I have been wanting to make a bedroom set for my wife and being a bit of a baseball fan I wanted to use hickory or ash. I am leaning toward the hickory but wanted to see if you guys have any experience or recommendations between the two. Thank you
-
-
- 27 replies
- 7.2k views
- 1 follower
-
-
I'm making a chess board, maple/walnut squares about 5/16" thick, glued to a 1/4" luan ply substrate. It is turning all pringles shaped. Short of building a box under it, does anyone have a suggestion to help keep it flat? Note that I have not added any border or frame yet, its just a bare board.
-
-
- 17 replies
- 2.9k views
- 1 follower
-
-
I picked up these two boards at a garage sale. Was wondering what they are????
-
-
- 22 replies
- 3.1k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·