Finishing
2,922 topics in this forum
-
Can you apply Rubio over a Minwax oil based stain without adverse effects? I have a real small, stained picture frame, and I’m not about to go buy colored Rubio just for this frame. I’d prefer to use the Rubio just because I have the scrapings of a can left over, and just want to use it up, but if it will cause issues, then I’ll pivot to another finish.
-
-
- 1 reply
- 3.2k views
- 1 follower
-
-
I am pretty sure I know the answer but thought I would ask. Has anybody successfully blended a new poly finish with an old? My wife wanted me to add a kitchen cabinet and make the butcher block counter grow. That part was easy, but now I have to refinish the counter top. My thought was to feather out the old poly then use a thinned coat for the first new finish. Google says no, but thought I would ask here. I think I am just trying to delay the inevitable, which is pulling the sink and refinish 23ft of counter.
-
-
- 11 replies
- 16.4k views
-
-
I'm doing a lot of research on HVLP sprayers for lacquer finish for spraying furniture. My budget is 500-600$. There seems to a split opinion on gravity vs siphon. This will be for spraying lacquer only. I have a graco 5 for paint. I'm having a hard decision of going with a fuji semi pro or buying an air compressor with a decent spray gun (like a husky or tcp gun). My real only concern with the fuji is it seems pretty loud and is constantly on whether im spraying or not. So my question is do you prefer gravity or siphon for lacquer and if the turbine setups are really better as some people claim vs the air compressor setup. I'm probably over thinking this as it seems lacq…
-
-
- 2 replies
- 2.9k views
-
-
We built a new house 3 years ago, and the cabinet finishers left the remaining finish behind. I put it in a new can, and just pulled it out today, and experimented with it. I'm hoping you guys can tell me what it is. I can give you some clues. When they left it behind, it was in a steel 5 gal can. The sides of the can had thick build up, and real gooey in the bottom. I canned the remainder up, and just opened the can today...since 2019. When I opened the one gallon paint can today (it is half full), there was a rubbery covering over the top of the liquid. I could dent it with my finger. It was a 1/4" thick layer all the way across. I pinched the rubbery layer b…
-
-
- 15 replies
- 4.2k views
-
-
I figured someone would know how to do this here.. The protective table pad (not the wood) was ruined recently. I was wondering if there was a certain type of stain to use on the vinyl liner. It is mottled with black a bit throughout the wrinkles and was wondering if this could be done with a certain type of stain, or would you use a typical wood stain for this type of work? Thank You, Ben
-
-
- 8 replies
- 7.8k views
-
-
I just finished a small table for a large house plant to live on. It is 14" square and 12" tall. My wife's friend wanted it to have a beach theme. So I used white oak with a whitewash water base stain. Now General Finishes whitewash stain allows the color of the wood to be seen through the whitewash so I decided to stain the wood blue before using the white. I mixed transtint blue dye with some whitewash. Worked great - one coat. Then 4 coats of whitewash to get the look I wanted. Then 3 coats of General Finishes water based poly. My mistake is that I only but one coat of whitewash (not a great sealer) on the underside of the top. When I picked up the top to inst…
-
- 1 reply
- 2.8k views
- 1 follower
-
-
I mixed some yesterday in 8 oz of poly/blo/ms, and dried perfect in between coats. I was able to wipe on 3 coats during the course of the day. Stored the remainder...approx 4 oz...in a sealed jar. Today I put a coat on, and the first coat using the remainder of the jar never dried today. Still tacky 8 hours later. Are you supposed to re-ad a little Japan Drier to the mix the following day, after overnight storage, or before the next time using it? Does it flash off in the mixture every day? Or, after adding it to to mix/blend, should it keep doing it's magic without having to add more before each use?
-
-
- 13 replies
- 5k views
-
-
Was working in the shop this afternoon and thought I’d post a cheaper alternative to Stop Loss bags (but still as effective). I ordered some drink pouches off of amazon and use them to store my finishes in. You can see from the picture that I mixed this batch of poly/mineral spirits over a year ago, and it's still good…can you say that about the can of poly you opened 2 months ago? I couldn’t, the throughput of my shop is too low. Like many hobbyists, I wasted more finish than I ever used, unless there was a specific need to use the whole can. This is what I ordered: https://www.amazon.com/gp/product/B088H5Z3S1/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=…
-
- 2 replies
- 4.4k views
-
-
Does any one have any experience with this stuff? http://www.rustoleum.com/product-catalog/consumer-brands/varathane/weathered-wood-accelerator I am playing around with the old vinegar and steel wool trick on white oak and am not getting what my daughter wants.
-
-
- 13 replies
- 17.4k views
- 1 follower
-
-
I picked up this small round and very ugly throw pillow for cheap at a thrift shop, which I thought I’d use on my shop stool. Among it’s ugly features were a bunch of yarn tassels that I promptly cut off and tossed in the trash. Thus cushioned I perched on my stool and contemplated the sanding task in front of me, how to better get at the inside surfaces of this deeply undercut piece. It was at the limits of what I could reach with my fingers and my finger tips weren’t making good uniform contact between the sandpaper and the wood. What I needed was some kind of sanding block or sponge that would conform to the curvature…. Hmm... What I needed was somet…
-
- 0 replies
- 2.9k views
-
-
I've used it before, but gonna try some new things. I'm wiping on 50/50 poly/mineral spirits, over 2 coats of stain on white oak. How many coats (not real thin) do you think I should build up, so that I have enough to barely sand smooth at the end? Today I knocked off the dust specs by BARELY dragging some 400 grit over the 3rd coat. What grit should my final sanding be with, and suggestions to clean up the white powder? Has anyone tried 1/3 poly, 1/3 mineral spirits, and 1/3 boiled linseed oil? Would there be a specific application for that, or just general furniture? Seems interesting to me, and I'm going to try it on my next project.
-
-
- 13 replies
- 4.5k views
-
-
Old trundle sewing machine cabinet. Converting into a vanity table for granddaughters. The current finish I “Think” is shellac. Should I strip this down and then prime and then use my latex paint? Thanks in advance
-
-
- 2 replies
- 3.1k views
-
-
I need to finish a Dewalt stand with Marigold paint. Can't find the color local. Any suggestions from brand for painting the plywood. I can get the black local, but want to order the same. Ordering from Amazon...
-
-
- 6 replies
- 3.5k views
-
-
Dining room table developed hairline cracks in surface in many places and directions as shown in attached picture and looking for a way to repair them. Not sure if it is an epoxy or very thick polyurethane on it that is cracked. Will I need to sand it all off and completely refinish or is there a way to fill these cracks, sand, repeat? I heard of magic with superglue and sanding but would hate to try something and destroy the table or create more work. Looking for help or recommendation for a rock star in Boston who can make the table right!
-
-
- 6 replies
- 5.6k views
-
-
I have a question about finishing some boards and tips for the future. The photos below show some hard maple that I am using for the bottom shelf of my bench. It is not important for this build, but the outside boards have a light red color as compared to some of the other boards. The finish I am using is just an oil varnish (Tried and True Varnish Oil). To be honest I cannot remember what these boards looked like before I started and if there were some clues to this red color. It does not matter for this project, but I can see on some projects you might not want these different colors next to each other in a panel or adjacent parts. Is there something to keep an eye out …
-
-
- 4 replies
- 3.4k views
- 1 follower
-
-
The attached picuture is a practice veneer piece. The goal for this finish ( ARS) is a high gloss smooth surface. But you can wee in the pics that the wood surface has som little holes that 7 coats of ARS app;ied with a sponge brush would not fill. I am looking for a filler that will dry clear. A colored filler is not acceptable because, while this pattern is all one species, it could be contrasting colors and the holes tne to be at the intersection of the pieces. I have tried Aqua Coat - it shrink so much that it does little more that the ARS. I could try epoxy but since I only need one drop per hole I would have a lot of waste. Don't know how small of a batch…
-
-
- 11 replies
- 4.4k views
- 1 follower
-
-
I have one idea of how to do this. Tape. Is there any other way that is better? Thanks
-
-
- 4 replies
- 3k views
-
-
I ordered some of their pre-stain conditioner online at the end of November 2020. They took my money and sent out a confirmation that my order was placed, but since then I have heard nothing. They have not responded to my emails or telephone calls. I have a feeling they are sort of a digital ghost ship, still plowing the waters of the interwebs but with no crew. I would really prefer the product rather than a refund, but at this point it isn't looking good.
-
-
- 15 replies
- 13.7k views
-
-
The old timer who lived here before, rolled and brushed paint over stained and top coated doors. Needless to say, his surface prep was nothing. End result, the paint has let go! You may have seen me post many times to use a good stripper containing methylene chloride. Forget the Citristrip. [emoji31] Stop sanding your brains out. This goes down faster than a fat kid on a seesaw. No dust, no box of sanding disks, no wear and tear on a sander. Same thing holds true removing an old finish on furniture. Try it, you may thank yourself one day. Please read and understand the safety concerns. Don't use indoors, heavy duty rubber gloves and eye protection. …
-
-
- 7 replies
- 3.9k views
-
-
Hi guys, what's the best finish to use for protection from water? It's going to be hidden so looks do not matter. I was thinking maybe a waterproof paint but I don't know if something else will work better. I'm making a cheap rolling cart for my kitchen to put some of the difference devices on (blenders, Foodie, vacuum sealer, etc.) I have a ton of floor space but limited counter space. As part of it I'm building in a box at one end of it that I was going to set the basin for the sous vide into that's also insulated to help maintain temps. So it's not going to get a ton of moisture but the top half of the box will probably get some steam/condensation when cook…
-
-
- 4 replies
- 3k views
-
-
I just had one of those "saved by the bell" moments... I was doing the final 320 grit sanding to the Maloof rocker Guild project, while listening to old episodes of Wood Talk. As I was doing the final sanding on the crest rail I listened to Marc express his disappointment with the finish he had used on his rocker. Things came to a screeching halt <REVERSE ALL ENGINES> The cans of Tried and True were NOT going to be opened this afternoon!!! After updating and reading the project comments, it was apparent that there had been a change in heart regarding the use of oil and wax finish on the rocker. Possible options suggested would be Watco Danish Oil or the goo…
-
- 12 replies
- 6.1k views
-
-
Help needed! My kids used kinetic sand and made a ton of scratches in our beautiful kitchen table. I quickly tried Tibet almond oil and murphys oil and it only made deep water stains in the grain. My husband came home hours later and sanded away the scratches and oil stains and applied 2 layers of polyurethane. Then he did some more light sanding and put on another layer of polyurethane. Thought the problem was fixed. The table looked different but still good. However it has been almost a month and now we are seeing new darker spots and some black areas. Hoping one of you experts might be able advise us on how to restore this beautiful table!
-
-
- 2 replies
- 4.1k views
-
-
All, First off, thank you for any insight. I am a total novice finisher so please excuse my ignorance. I'm finishing up the Morris chair build from the Wood Whisperer Guild (Marc's guidance has been a great learning experience). Marc uses Waterlox as a first coat. I believe that it is oil-based and penetrates into the wood to enhance the appearance of the grain. He then uses three coats of lacquer with no sealer in between (sanding sealer/shellac). I have applied the Waterlox and it looks great (see pictures). My questions are as follows: What is the reason for applying the lacquer? It seems like Waterlox is used as a finish on a lot of projects (ev…
-
- 23 replies
- 9.4k views
-
-
This all natural edge redwood burl slab came from a tree on the N. Coast of CA in 1972. I bought it (you could buy redwood burl back then), ran it through a planner, then refinished it with Carnuba wax -- 50 years ago! Then it got moved around, stored, weathered, and to my chagrin, unattended for too many years. I'm trying to bring it back but it's badly wounded. 7 feet long, 3 feet wide at the widest, and 4+ inches thick sitting on natural redwood drift wood. It's over half (60% or so) birdseye burl. Amazing piece. What would be your best advice to saving this table (and preventing any further cracking or splitting)? The pic showing the burl (birds…
-
-
- 12 replies
- 5.9k views
- 1 follower
-
-
Any methods to keep the stone from picking up color of the dark stain? Usually just pre stain but that's not keeping the turquoise from being discolored on this one. Any help would be much appreciated
-
-
- 17 replies
- 10.4k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·