The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
How do I get it to where the breadboard isn't going to expand past my perpendicular panel? Is there a good, efficient way to minimize it? 8/4 walnut, biscuited panel, planning to t&g the bb into place and then sticking a few dowels through as well. What's the best practice? Am I on the right track?
-
-
- 11 replies
- 3.2k views
-
-
I made my friends a walnut/maple end grain cutting board last year. Their son has a nut allergy. Does anyone know if this could cause issues? Or is it a non-issue? I am wondering whether to ask for the board back and making them one out of different woods. Thoughts? Thanks.
-
-
- 20 replies
- 37.9k views
-
-
Heading to a friend's house tonight... she's got a 10' long, 9" diameter cutoff branch from her walnut tree that's been sitting in her field for about 6 months. Should I bring it home to have milled up and dried or am I risking a bug party at my house?
-
-
- 5 replies
- 2.6k views
-
-
That's right, real rose wood. Not rosewood. Wood from a rose bush. I pruned the crap out of a rose bush today, and ran the thickest stalk across the jointer just because. Thought you guys might find it mildly interesting. The outside of the stalk was a solid 1.25" And here it is: Some interesting figure where the thorns protruded from: I like taking random plants and playing a rousing round of "Will It Wood." The answer for a 1.25" knockout rose stem is "probably not." It's all punky in the center. Still looks pretty neat though.
-
-
- 12 replies
- 5.1k views
- 1 follower
-
-
I have a bottle stopper blank of zebra wood, with what looks like birds' eyes (enlargements) all over it. Looking @phinds site, I see that these are not common, but not rare either. My question is, how deep do these usually penetrate the wood? Do they change frequently as one goes down through the wood, or do they run fairly deep? I ask because it kind of affects how I plan to turn it. I might turn it facegrain, so the enlargements will sit upon the face/top of the stopper if they don't run deep. But if they do go deep, I'll turn it like a spindle and hope they appear all over the piece. It's only a 2" cube, so there's not much to go on, and of course…
-
-
- 6 replies
- 2.7k views
- 1 follower
-
-
I have a panel for a project that I am working on. It has been milled to the point you see in the photo for 5 - 6 days. I worked with it yesterday fitting the pieces that go in the slots and taking some measurements for the sides. Through all of this everything has been fine. Today when I went out into the shop to continue, I found it in this bowed state. It is setting right were I left it last evening. There is also a similar piece that has a bow in the opposite direction. I am in Northern California and don't usually have things like this happen. I don't ignore wood movement but it isn't a big concern like some of you deal with in other parts of the country. T…
-
-
- 50 replies
- 10.1k views
- 1 follower
-
-
-
I was recently in Honduras and had the chance to check out a small woodworking shop there. They were using several woods that I had never heard of before. It is possible that I simply couldn't tell the wood species because of the different language, but I think there were also species I had never seen. Does anyone know of any books/resources that could help me learn about foreign wood species?
-
-
- 11 replies
- 59k views
- 1 follower
-
-
I remember a while ago a discussion about using ebony for rockers instead of wenge but others said good luck finding a single piece that long.. so how long does it have to be? These did not come home with me and I didn't ask the price but I'm sure it is OUCH
-
-
- 11 replies
- 2.9k views
-
-
I suck at it. I'm rough milling hard maple for two kitchen helper/learning towers. I've now milled two or three full boards only to notice open pores when they come off the planer. Ash I guess? Now I need to find use for a bunch of 4-6" wide 20" long shorts. Anyone else have the same problem?
-
-
- 19 replies
- 4.8k views
-
-
I've made many dozens more updates in the wood name database http://www.hobbithouseinc.com/wood_name_database/index.htm NOTE: @Trip discovered that I had a path error, which I have now fixed, so if by chance you downloaded it before 1:30 EST today, you need to download it again to get full functionality.
-
- 0 replies
- 2.1k views
- 2 followers
-
-
Does anyone have any info on where I can purchase boards in the ny,nj area. Preferably at a reasonable driving distance from NYC. I've been purchasing whatever hardwood they have in stock at Lowes and Home Depot but the prices are extremely high and they only cary 3/4" stock.
-
Hey Guys, I have access to both flat sawn and VG walnut. I'm looking to build a mirror frame. Specifically it is going to be essentially Marc's mirror. Does anyone have any tips on pros or cons of using either type of wood?
-
- 2 replies
- 2.3k views
-
-
So I've now turned 2 pens with purpleheart and both have turned brown. As I've been reading, the color changed once cut from brown to purple taking anywhere from a few days to a few weeks and then, with exposure to UV light, it will turn brown again. My question is what causes it to turn purple in the first place? Exposure to light? Oxygen? Should I wait a few weeks after turning to finish it? I just bought a big chunk of it to turn into a larger version of the dice caddy I posted last week and I want the rich eggplant color to offset bird's eye maple. Should I build the piece and just wait to finish it? How do I get the rich purple color I'm seeking?
-
-
- 6 replies
- 2.5k views
- 1 follower
-
-
Does anyone know of someone in the Nashville, TN area with a kiln for drying wood? I’ve got a hundred or so bd/ft of white oak that has air dried down to about 20% and would like to get it down for a table I’m about to work on. I’ve called a few lumber places and they all don’t allow public to dry in their kilns. Does anyone in this area have a solar kiln? I’ve looked into building my own but don’t have a lot of need after this wood is dried. Thanks.
-
- 0 replies
- 2.8k views
-
-
Hello all, I'm new to this forum but have a few questions about a new project of mine. I came upon a 8' live edge slab of black walnut 2" thick and ranging from 26-24" wide- The slab is only live edge on one side and not quite wide enough by itself for my table. I'd like to add width to the table to get it to at least 30 inches wide. I have a million ideas on how to do so but ultimately I believe I'd like to add a second live edge to give it the width I'm looking for..... in thinking of using a completely different wood like maple, it would be a great contrast, like the sapwood of the walnut. Does anyone have any brainstorming thoughts or opinions here or see any…
-
-
- 9 replies
- 2.6k views
-
-
My borhter in law is in VA and just starting woodworking. The last time I was there I tried to find a source for hardwoods without success. Anyone know of a source there?
-
-
- 3 replies
- 2.5k views
- 1 follower
-
-
This must have taken a huge amount of time. Apparently they sliced of thin sections over and over and over and over again and took a pic after every slice and did this with several woods. It REALLY shows how the woods look as you move though them. https://player.vimeo.com/video/196683500
-
-
- 9 replies
- 2.9k views
- 1 follower
-
-
Turns out a cousin I've never bothered to meet (my family is odd, these things happen) was a woodworker and called it quits. My brother got in contact and got a price. $150. I said yes sight unseen. I figured unless it's nothing but pine offcuts, then it's probably going to be worth it. It came on my bro's trailer that he carts cars around on. Right away I saw a couple of 3 3/4" walnut boards, about 8-9 inches wide, around 3 foot long. I saw this board, which.. looks like oak to me but has wild grain. I don't know if it's just figured red oak or something else? Saw this, I have no idea what it is, looks cool. It's a weird s…
-
-
- 26 replies
- 6.8k views
- 1 follower
-
-
I know you have to glue and press the pieces together but does anyone have advice on what glue to use for laminating wood or where to find a how to maybe? This is my first attempt.
-
-
- 6 replies
- 2.8k views
-
-
Hi! I want to use ebony for some accents on a coffee table I'm building. The top will have draw-bored breadboard ends, and I want to use Ebony for the dowels. I'm also doing draw-bored bridle joints in the base (see Ishitani's Kigumi table). The dowels for the top will probably be 5/16 or 3/8. The base dowels need to be 1/2. Has anybody used a dowel plate (Lie-Nielsen, or any other), to create dowels out of ebony? How did they turn out? Any tips for success? Obviously, I don't want to screw this up. Ebony's expensive as hail. Thank you! Chris
-
-
- 22 replies
- 5k views
-
-
I know of a few guys who have mills on the side. I see the hobby mills as a bit of a gamble...some kiln dry, some air dry, some sell wet. Bugs might be an issue if not kiln dried. I haven't explored their pricing too much, but realize I won't be willing to pay the same as I would from Eric's place, where I trust. With that said, I wouldn't mind stickering a few hundred BF in my basement for future use, even if it needs a year or longer to dry completely. How should I expect pricing to be though? Is there a rule of thumb? 10% less than retail? 50% less than retail?
-
-
- 30 replies
- 7.6k views
-
-
So I'm building a bookcase. Because of an issue with the baseboard heaters in my apartment, the bottom of the back legs need to sit back 3" from the wall. I discussed it here: Wood movement over a heater I've decided to do a Krenov inspired case. However I decided to do something I've not attempted before - curvey, criss crossed legs (see attached). I was planning on making it from cherry. Just for scale, they are currently 1.5" square. The circle at the crossing point will be a dowel running between the two sets of legs to add to the stability and stop the legs from splaying. I'm planning on using aprons between the four legs. How should I best orientate t…
-
-
- 24 replies
- 3.5k views
-
-
I am working on a project that is going to have me putting in a fair number of plugs, walnut plugs into cherry. I always take the time to line the grain in the direction of the grain it is going into. It got me to thinking, do most of you do this or do you just put glue on them and slam them home all willy nilly.
-
-
- 62 replies
- 10.5k views
- 2 followers
-
-
Any tips on buying slabs? Would they usually go in a kiln? Ive found these: https://www.ebay.com.au/itm/192204799785 edit: the link isn't working. The slabs are about 35mm (1.5") thick and of different sizes for $175. I just spoke to the seller and he'll take the starting price for them. They're air dried though and have only been cut for about a year. Going by the year per inch drying rule they need a bit more time.
-
- 8 replies
- 2.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·