The Wood
Choose the right lumber for your project. Compare wood species, grades, and plywood, and get advice on moisture content, acclimation, and wood movement.
1,451 topics in this forum
-
Outside of Füssen, Germany. Czech Republic was similar. I saw many small mills, no large ones. They still grow and mill hardwoods and I saw large (3-4 ft diameter) hardwood trees along our Czech route. Lower elevation trees in the alps are predominantly hardwood. Pine, and I think hemlock at higher elevations (highest elevation in this region was about 9,000 ft.)
-
-
- 8 replies
- 2.7k views
-
-
Hey All, Dad and I were turning some Red Oak logs into lumber with our Wood Miezer the other day and had a disagreement about how to cut it. We currently have a bunch of 4/4 Red Oak so I wanted to cut some 6/4 and 8/4 boards to have on hand. He didn't like that idea saying "nobody is gonna want that, there's no market for it" so we compromised and cut most of it to 6/4. I'm gonna personally make a floor lamp out of some of it but I'm curious to know what kind of stuff you could build with 6/4 and 8/4 Red Oak. Trestle table comes to mind. Puttin the feelers out. Rich
-
-
- 20 replies
- 6.8k views
-
-
Just got back from the lumberyard. Since a week ago, my company pricing for 4/4 Black Walnut went from $6.27/bdft to $7.96/bdft. I asked him what the 'civilian' price was and he said it's over $12/bdft now. I'm in Idaho, what's it like where you guys live?
-
-
- 37 replies
- 7.8k views
- 1 follower
-
-
Here in Nova Scotia, we often have daytime freezing temperatures for 3+ months of the year and my workshop is unheated when I'm not working there. If I'm drying turned bowls in there how will this effect the wood? I'm assuming the drying will be non-existent during that time? If I move them into my temperature controlled apartment, am I asking for them to dry faster and possible cause more splitting and checking? NB This is a cross post from the turner's corner
-
-
- 15 replies
- 5k views
-
-
I am working with hickory, and had this piece of wood sitting outside in the sun for about an hour. The temperature was about 95 degrees F, and the board started to crack (I'm guessing from wood movement from the temperature change). I immediately took it into a cooler area but have seen no improvement in the past few hours. There was a small, visible split in the wood before this incident, so I filled it with epoxy and it fully cured since then, but it still cracked when put out in the sun. I was wondering if there was anything I can do to both fix and prevent this from happening in the future. I am planning on finishing the piece with a water based polyurethane, and it …
-
-
- 8 replies
- 3.6k views
- 1 follower
-
-
I am fabricating cabinets for my wife's craftroom. My local supplier has a range of plywood types and I was curious what I should use if I plan to paint these? I am leaning towards frameless construction, which means prepping the edges somehow for paint. Birch? Baltic Birch? Alder? Maple? Something else? Any tips would be appreciated.
-
-
- 6 replies
- 3k views
-
-
These came in a few weeks ago and I decided immediately I'd own one. Found the best of the bunch and called dibs on it right away. This is the center of the tree, so it's almost completely quartersawn and pith. A little bit of riftsawn approaching the pith which will make good secondary parts. Heavy, large fleck in the QS areas and lots of cool colors. 10' long, 36" wide, 10/4. I won't be using it as a slab (big surprise) so the pith doesn't bother me. I'll rip it in half before I even take it home. The plan right now is to use it for the cabinet end of a JK cabinet on stand. I've never been able to get my hands on good QS sycamore in the past so this is a re…
-
-
- 34 replies
- 8.3k views
-
-
Howdy Folks, I just got my hands on some olive wood and want to make a jewelry or make-up box for my wife. What would be a good accent wood to go with that? THis is my first project that will not involve rebuilding the fence or wood from the box stores. Wish me luck. Rube
-
-
- 18 replies
- 6.8k views
-
-
A while back I bought a piece of AC plywood from a local big box store. Wasnt plywood from HD or Lowes, but I wouldnt call great quality stuff either. I dont know the brand. Anyway, I went to make a small dust frame out of a piece of that plywood, and it was a big waste of time because the pieces I cut were bowed. Had to scrap the whole thing. So my question is, did the plywood develop this bend because its low quality, or does good quality plywood move like this too? Is it because one side of the plywood is one grade, and the other side is a different grade? Thanks.
-
-
- 20 replies
- 4.4k views
- 1 follower
-
-
I am new to woodworking, so I need wood well a quick look through the Craig's list I find a local gems selling maple figured slabs so I buy a slab and make a coffee table for my son (see pic) first woodworking project Turned out nice I finished the top with a local product call "mirror coat bar top finish 2 part epoxy glass smooth finish and ada a 3- d effect then I go for a visit and a longer talk with this gent xome to find out he has a FRIEND that works at the mill where they only mill for the music industry oh really? all he has are large slabs so I ask "can you get me something thinner and smaller? ca…
-
-
- 21 replies
- 3.7k views
-
-
https://www.namm.org/issues-and-advocacy/regulatory-compliance/cites-update-commercial-rosewood-and-bubinga
-
-
- 20 replies
- 4.5k views
- 1 follower
-
-
I visited my local wood place and was very disappointed in with their walnut selection and price. At $11.20 a bf for 8/4 walnut that was mostly all sap was not happening. So, I decided to call around to a couple places in the area. Came across a place called National, and at $9.55 a bf for 8/4 I was happy to put in an order. The difference in price per bf paid for the shipping, and I still saved money. While I was at it... ya know, having fun with the idea of getting wood without leaving the house I decided to order some 8/4 cherry and 8/4 hard maple. Cherry will be used for a built in, and the hard maple will be used for my workbench. The cherry is 12' long, the …
-
-
- 7 replies
- 43.9k views
- 1 follower
-
-
Alison and I went down to Ruidoso, NM last weekend. There's a carver there that also sells burls and unusual pieces. Big Burl!
-
-
- 11 replies
- 3.2k views
-
-
Found this left on a job site I was cleaning up, just wondering what kind it is
-
-
- 26 replies
- 7k views
-
-
A little wood porn for ya. Bookmatched Figured Red Wood Veneer. You will notice the grain is actually running north south, while the figure/quilting is running East west. Each piece of veneer is about 16" wide, and 14' long, there are 2 pieces in this photo, with a bit of a third beneath the one.It was on a pallet of maybe 300-400 bf of this veneer, all pretty much identical figure. The figure is so pronounced, that in the right light, it looks severely warped, and you have to lay your hand on it to convince your brain it actually is flat.
-
-
- 14 replies
- 3k views
-
-
A friend bought a piece of birds eye maple that has been heat treated (roasted) to give a great colour. My question however, is if it is the same colour all the way through. If it's sanded, will the colour be the same?
-
-
- 2 replies
- 2.5k views
- 1 follower
-
-
I discovered a single board in my stash of lumber and I am not sure what it is. I jointed two sides. It is really white and straight grained. It is not birch, poplar, or maple ( I have samples of these in my shop). The only wood that comes to mind is holly but I have never actually handled any holly. So, any help is appreciated. Thanks. Here are some pics:
-
-
- 25 replies
- 6k views
- 1 follower
-
-
At work the other day, we made a bunch of structural elements for a piece out of alder cutoffs. We usually just use 1"x1" - 2"x2" x 14' maple pieces, but if our mill has some lumber leftover from a project, they mill that up in to blocking material. Seen Walnut and Cherry come through this way already. Having never seen any, I was kind of impressed with the Alder, nice grain, nice color, similar to cherry. One guy said he hates working it as it's too soft. What's your opinions on it?
-
-
- 10 replies
- 3.2k views
-
-
You can find a couple of versions of this on the Internet but I prefer this one by The Lindsey Family, (http://www.lindsey-family.com/cms/index.php?page=store) and I now have their permission to post their rendition, ripped off of their 8th album (out of 11 they've released so far). My personal preference for this version is both because I think it's the best but also because "The Lindsey Family" is my sister's boy and his 11 kids. I've known him since he was an infant and I've known all 11 kids since they were infants and I love them all dearly. Their music started out as just gospel music but has grown to include other genres. They parked their tour bus next to my house…
-
-
- 3 replies
- 2.6k views
- 1 follower
-
-
Anyone know of a reputable source, that might have a bookmatched pair of red oak 8/4 - 10/4 boards or slabs that would together make a 46" wide table top, at least 66" long? I can pick up in a 3 - 4 hour driving radius of Jackson, TN. That puts me close to St. Louis or Chattanooga, maybe Jackson MS. Farther than that, will probably cost less to ship. My day-job boss has asked if I can build a 'unique' table for him. Working out the details, but he wants a thick red oak top, not live edge, but slab-like. Some sort of trestle base.
-
-
- 31 replies
- 6.4k views
-
-
While I don't think it would. I would like to pose this question to those of you that know a lot more about wood movement than I. The arrows indicate grain and you can assume each strip is 2" or 3" wide. The more I look at it the more it kinda rubs me the wrong way but it was fun figure out how to get a harringbone to go 4 directions. Sent from my XT1585 using Tapatalk
-
-
- 18 replies
- 3.6k views
-
-
I picked up a number of spalted oak, spalted maple, and a little bit of cedar off cuts (still plenty of meat left on the bone) yesterday and noticed that termites had made their rounds in oak when it was still standing and I imagine they might still be lingering in the wood. I was planning on bringing the wood into the shop to finish drying out and don't want to bring in a bunch of critters with it. So what do you all recommend for a treatment prior to bringing it into the shop? Sent from my SM-G950U using Tapatalk
-
-
- 5 replies
- 2.9k views
-
-
Hey All, I'm relatively new to the Woodtalk Forums so I hope this is an appropriate post. My dad bought a Wood Mizer portable saw mill about 25 years ago and he worked it for many years. About 20 years ago he bought 500 hardwood logs that he milled up, air dried and stored in a pole barn. We still have a lot of lumber left and I've been tasked with selling it. We're here in Beaverton MI. We've got a variety of stuff. Red Oak LOTS White Oak Curly Maple Spalted Maple Black Walnut - only a little left, we're in the market for logs Hickory Ash Poplar Basswood Most of the stock is 4/4 but we do have some 8/4 white oak and black w…
-
- 0 replies
- 2.2k views
-
-
A couple years ago I picked up a grab bag box of 30lbs of pen blanks. They are random domestics and exotics. Some I could Identify, some I cannot. These are the blanks from my Scrap box Special project I'm working on. If anybody has a clue about any of them, it'd be appreciated. If not, oh well, I'll make something up, like I do when I sell these as pens. Apologies for the focus. I should have broken out the macro adapter for this. They looked ok on the preview screen, but when I downloaded them, ugggh. I already have the blanks in the first glue up, so end grain shots are out. A) C) D) E) Walnut? …
-
-
- 23 replies
- 4.3k views
- 1 follower
-
-
Can anyone tell what kind of wood this is? Looking for something that compliments white oak on my next project
-
-
- 10 replies
- 3.2k views
- 1 follower
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·