Video and Project Showcase

Project showcase and videos.  Post video journals in the Journal section

Posting Rules

This space is not intended for spam or to drive traffic to your channel/site. If you post a video, please be sure to include a paragraph of text about the video and make sure the video is embedded. The forum usually embeds the video automatically if you drop in the link. 

299 topics in this forum

  1. Dewalt DW735X Project

    By rainjer,
    • 20 replies
    • 4.7k views

  3. Somewhat Stickley inspired sideboard 1 2

    By B1rdhunter,
    • 36 replies
    • 8.8k views

  4. Fun with scraps

    By Bmac,
    • 3 replies
    • 3.8k views

  5. Practice inlay piece

    By difalkner,
    • 8 replies
    • 4.1k views

  6. Walnut Door

    By Coop,
    • 22 replies
    • 5.2k views

  7. Spurtle's and Easels

    By treeslayer,
    • 8 replies
    • 3.7k views

  8. Stereo Cabinet

    By woodbutcher,
    • 12 replies
    • 5.3k views

  9. Air filter cabinet.

    By rainjer,
    • 2 replies
    • 3.8k views

  10. Knife Storage

    By Chestnut,
    • 6 replies
    • 3.4k views

  11. Leaf, vine - test inlay piece

    By difalkner,
    • 2 replies
    • 3.2k views

  12. Kitchen Renovation

    By Chet,
    • 16 replies
    • 8.1k views

  13. Garden gate and fence

    By jussi,
    • 11 replies
    • 4.8k views

  14. Carved wall cabinet

    By Ronn W,
    • 11 replies
    • 4.3k views

  15. Dining table construction advice

    By SAZ,
    • 16 replies
    • 5.2k views

  16. Done!!

    By Randall Child,
    • 5 replies
    • 4.2k views

  17. Maloof #2

    By Randall Child,
    • 9 replies
    • 5.2k views

  18. Dice game

    By treeslayer,
    • 11 replies
    • 4.4k views

  19. Another simple home addition

    By collinb,
    • 5 replies
    • 4.9k views

  20. Federal End Table

    By Hammer5573,
    • 12 replies
    • 4.7k views

  21. Sharing a great link, and boxes in no time

    By Bmac,
    • 22 replies
    • 6.2k views

  22. Simple Bookshelf

    By Chestnut,
    • 2 replies
    • 5.2k views

  23. "Canopy"

    By Mark J,
    • 9 replies
    • 4.8k views

  24. Custom TV Stand

    By PPBart,
    • 4 replies
    • 3.6k views

  25. Cherry plaque for Katie

    By difalkner,
    • 0 replies
    • 3.4k views

  26. Cherry plaque for a friend

    By difalkner,
    • 6 replies
    • 4.2k views


  • Topics

  • Posts

    • Coop
      Slow Server?

      By Coop · Posted

      I’ve briefly known folks that get their jollies by pissing people off.
    • Ron Swanson Jr.
      Slow Server?

      By Ron Swanson Jr. · Posted

      What a sad state of affairs the Internet has become. Can't even have a tiny, harmless little WW forum without it being constantly attacked. What could there possibly be gained from harassing this forum???
    • Beechwood Chip
      Slow Server?

      By Beechwood Chip · Posted

      WTO was down briefly at 5:53pm Eastern.  I emailed Marc, and now it's back up.
    • Von
      Von's shop tour and setup log

      By Von · Posted

      [Oops, this post was supposed to go in my workbench journal.] Flush cut my pegs and cleaned up the glue squeeze out from the long rails. I noticed a couple of the pegs broke below the surface so I applied a little wood putty to smooth things out. Started on the shelf. I'm sandwiching two pieces of plywood under and over a cleat to make a void I can fill with, e.g., sand bags if I decide I want more mass.  Chance to break out the pinch rods. I added a 1/16 shim so I'd have a little play and also moved the rods around to find the tightest spot. The rod just moves right over to the table saw, without the shim, to set the fence and cut the shelf to width. For the shelf length, I used a tape measure since my rods are not long enough. Less fun but good enough. I cut the shelf to length (45") with the track saw. I cut the corners to fit around the legs with a Japanese pull saw and did a little shaving with a low-angle block plane where the plywood was too tight. Bottom of shelf fits. Top part and cleats to follow tomorrow.  
    • Ron Swanson Jr.
      What did you do today?

      By Ron Swanson Jr. · Posted

      Yesterday was my day to host the meeting for the box Makers SIG that I'm part of. I was to give a demonstration on hand cut dovetails.  I have never done that in front of an audience. I learned there's a pretty big difference between peacefully working alone at my own speed,  And trying to go fast through the process with 5 guys literally standing over my shoulder.  Still a good meeting and enjoyable time with a good group though.   

  • Popular Contributors