The Shop
1,954 topics in this forum
-
I have what I think is a goodly assortment of clamps ranging up to 4 feet in length, but no matter how long your clamps are there's bound to be a need for one that's longer. I had a 5 foot clamp job and was lamenting this fact to one of the guys at Woodcraft. He suggested that I make a yoke from plywood. The idea is probably not new, but I'll explain. Take say a 2 feet long piece of plywood. A few inches in from each end cut a rectangular hole big enough to accommodate the fixed jaw of a parallel clamp. Now "link" two clamps together with the yoke. Two 4 foot clamps can now span 9 feet, or more with a longer yoke. I got home, looked at my project and sai…
-
-
- 35 replies
- 8.1k views
-
-
I didn't take any before pictures so you are just going to have to take my word that this is a much better set up in my shop then it was in the beginning of July. The things that have changed - Added a proper miter station. The bandsaw was next to the router table but I turned it 180 degrees and moved it to the end on the miter station, lots more room now, before it was kind of a squeeze between it and the miter station. Clamps moved to their present location which is right behind me now when I am at my assembly outfeed table, they were on the opposite wall. Built a permanent stand for the drum sander which raised it up so it above the miter station for better out fee…
-
-
- 20 replies
- 4.2k views
-
-
Putting up some insulation in my garage shop. The walls are poured concrete and just soak up all the heat from my heaters in the winter. I know framing it out would have a higher R value but I don't want to sacrifice shop space. Now I just need to finish the other walls, drywall, sand, paint and run electric! Sent from my iPhone using Tapatalk
-
- 4 replies
- 3k views
-
-
I was asked to post a shop tour, so here we go . . . . The building is a 42’ x 72’ pole barn built by FBI (Farm Buildings Incorporated) with half shop and the other half storage, aka “the barn”. It has concrete floors throughout but the shop floor was raised and wood floors installed so you don't have to stand on concrete all day. This also allows room for the electric and HVAC to be run under the floor and provides some storage. The electric is 200 amp service and it has a forced air furnace. There is also a bathroom and slop sink in the shop. Most of the machinery is Powermatic and Jet. There are two table saws, an older PM66 which still runs great, an…
-
-
- 33 replies
- 8.7k views
- 1 follower
-
-
My wife is on a dog kick recently, and i think things are becoming serious. She keeps texting me if a 7 hour drive is too far for this and that breeder. Ive only had a family cat and koi when i was younger, so i dont know much about dogs, but i do know they can hear very well. Is a basement woodshop detrimental to a dog's hearing? i dont want to shoot down her dream of owning one or two french bulldogs, but the line in the sand is drawn. Im not giving up the woodshop, and i dont want to kill the little buggers with excessive noise. I googled the topic--no surprise, the woodwhisper had an article on it--but i dont intend to have the dogs IN the shop EVER. No one mentioned …
-
-
- 32 replies
- 8.4k views
-
-
Saw this shop in southern France built into a limestone cliff. And the view in the other direction
-
- 3 replies
- 2.9k views
- 1 follower
-
-
-
-
- 24 replies
- 5.1k views
-
-
Watched a video on this today as a coat of finish was drying. Does anyone have one of these in their shop? Would love to hear about it if anyone does! Might make a nice addition... The vise I am referring to is the first one displayed in the video.
-
-
- 9 replies
- 5.4k views
-
-
I won't go so far as to call this a tip, but it worked for me. I bought a Makita SCM eleven years ago and I love it, great saw, but it throws dust everywhere even with the Festool vac hooked up. I was toying around with cardboard and stiff plastic sheet trying to come up with some sort of shroud without success. Then I propped up the shop vac hose using one of the hold down clamps and shazam, pretty good dust collection. Not perfect, but way better. You do need to check before each cut that the vac hose clears the blade.
-
-
- 11 replies
- 5.5k views
-
-
Originally I was going to run a 6 inch trunk run down the middle of my ceiling and branch off. But, my shop isn't huge.. and I'm starting to think the 6 inch would be over kill since I'd be branching off with 4 inch anyway... The furthest tool from my dust collector is about 25 ft away at the end of the run. But I can disable that part of my run with a blast gate and the next tool, my table saw is at about.. 20 ft from collector intake to tablesaw port... 3hp motor.dual dust bags. Just wondering ig I should even bother with the 6 inch since it's really not that far... and I'm not hooking up 20 tools to it... I can manage it with blast gates when using a specific side of t…
-
-
- 9 replies
- 3.8k views
-
-
Does anyone have any comments about the new Laguna CFlux DC line (e.g., http://lagunacleanair.com/product/cflux3/). I really like the form factor and they seem to have made several improvements over the previous generation of "short cyclones". Does anyone see any obvious cons with respect to, e.g. the Oneida V3000?
-
- 8 replies
- 5.4k views
-
-
I'm looking at an Incra 1000HD on Craigslist, being offered for $125. I've gone back and forth on the idea of an aftermarket Miter Gauge, and Incra seems to be well-liked. Some incra products get called out for being fiddly, which is not my style, but having sub-degree accuracy sure sounds like a dream. So, beyond consulting @TerryMcK's flowchart, what do you folks think? Anyone used an Incra's Miter Gauge?
-
- 9 replies
- 4.3k views
- 1 follower
-
-
I just got a miter saw (Kapex) and need to build a miter saw station for it in my garage workshop. I'm thinking something permanently up against a wall rather than on wheels. I don't love building shop furniture, so simpleish would be nice. Does anyone have a design they like?
-
-
- 29 replies
- 7.5k views
-
-
Hey all, nearing the end of my big tool purchases and have a question on layout. Been using the below for about 2 years now and it's worked ok, but wanted to get peoples thoughts on the layout, particularly since i plan to add a lathe and router table to my arsenal soon. Overall it's 26 x 11 foot shop in the basement and most of the tools are on wheels. I eventually want to run ducting for the dust collector but don't mind wheeling it around for now. I dont have a dedicated miter station in the plan, but would be ok moving that onto the outfeed table if it saved floor space...plan to do that with my spindle sander already. Any thoughts? - Thanks, Ted
-
- 11 replies
- 3.9k views
-
-
It's Festool, comes in a systainer, some bits are green and Barry appears in the vid....what better reason to watch?? LOl. Click the link if you are curious. https://youtu.be/fV6gFJ26lgg
-
-
- 10 replies
- 3.1k views
-
-
A while ago, I almost bought a Laguna 14twelve band saw for my shop. I decided that I wanted the Festool Kapex more (and it was on special), so I bought the Kapex instead. My tool budget is growing, and I am getting close to the point where I can buy the Laguna. I called Atlas Machinery today, and was quoted 200 dollars shipping for the saw (about 300 lbs) and the mobile base. The distance is approx. 100 km from their showroom to my door. Is this too much for delivery? I could see if it was coming from the states, or western Canada, or something.
-
-
- 22 replies
- 3.9k views
-
-
Hey guys, I've been thinking quite a bit lately about trying to get my (garage) shop into better shape to make it more fun to work in... I had posted in the other thread about painting the walls, I've still got a workbench on my to-do list, and I'm looking a lot at storage. Right now my hand tools are scattered around the garage and mixed in with my power tools or with miscellaneous household stuff stored in the garage. I'm thinking the next priorities should be getting my walls painted and set up with better hanging storage to get the non-woodworking things out of my way, then I want to put up a hand tool cabinet. I'm not looking at going completely over-the-top det…
-
-
- 36 replies
- 13.7k views
-
-
We have an 11x19 shop and I am planning on building an 11' plywood counter at one end for workspace and to hold all the small hand tools on an open shelf. I want to be able to build plywood bases for our drill press, mortiser, and router table, and then be able to slide the tools to one side or the other if we are not using them. My simple idea was to put bench dog holes along the front and back of the counter, as well as in the four corners of the tool bases. Questions: 1) do I need to put melamine on the counter and tool bases to allow for the sliding? 2) will I still need to clamp the tools to the front of the counter to use them safely? 3) do I n…
-
-
- 9 replies
- 3k views
-
-
I need to down size from a rented shop of 1,000sf to a one car garage. I have a Powermatic66, Bosch 4100, a vintage Shopsmith and a track saw. My gut says loose the Powermatic66. What say you?
-
-
- 18 replies
- 4.4k views
- 1 follower
-
-
Wasn't as stifling today as past few weeks, so we did a little pre-fall cleaning......
-
-
- 12 replies
- 3k views
- 1 follower
-
-
So just sent off my plat and other stuff to an Architect, Hopefully putting on a garage addition on my house. 36 wide along the front section on the left is 12 feet wide by 24 deep then 24 feet wide by 31 deep. Needed 27' to park the boat.. i have a good 12 x 31 feet shop area for tools and such. i also have a whole wall on the other side i plan on putting the jointer and planer. Next stop HOA =/
-
-
- 13 replies
- 3k views
-
-
Now that the shop is relatively clean and I am between projects, I thought I would share my space with you all. The ugly thing in the fore ground is an old kitchen base cabinet on wheels. It is usually in the way but come in handy for finishing and misc storage Jointer is on blocks so that long pieces don't hit the table saw. Drum sander is on wheels. Spindle sander stored under workbench. Empty wood racks, gotta restock. Sharpening station, small block of granite for stone flattening Easy to reach blast gates for table saw and router That's about it. This is where I love to spend my time. Glad I could share.
-
-
- 19 replies
- 3.8k views
-
-
My shop is in a detached garage. I recently ran some underground conduit over to it from the house and installed a 100 amp panel to upgrade my electrical needs in there. Last winter, I had a small propane heater that I would run for a bit before working in there, and once I got moving it was comfortable. This year, I was thinking about possibly putting a few baseboard heaters, just to take the edge off here and there. I've also been looking at solar heaters etc.and looked at a combo unit, for AC and Heat that could just be cut into one of the walls... Also considering a de-humidifier. Anyone go through this process? Got any good suggestions? Thanks.
-
-
- 13 replies
- 3.7k views
-
-
Hello. I'm new here and a refugee from WoodOnline, which is closing next week. I was a host there for nearly ten years back in the 90s and on. I was also the forum administrator/moderator for the Ryobi Tool Forum before it was withdrawn. I am building a new shop in the basement of our new home. I had to pack up my old 12'x12' shop of 30 years in our old home. The new shop is also in the basement, but is 12'x22' this time. It will be laid out pretty much like the old one with a few changes to fix things from the old shop. Right now, I have the walls framed and am in the process of wiring the shop for power and lights. One of the big changes in the new shop is LED …
-
-
- 34 replies
- 5.4k views
- 1 follower
-
-
Hey there guys, I'm upstate NY right now, and by upstate I mean right by lake ontario so as north as you can go before going into canada lol. I am trying to "weather-ize" my shop. as it stands currently, this summer has been brutal, with temps outside reaching 95+ I wasn't able to stay in. The shop is in a 3 car garage, 3 of the walls are insulated along with the ceiling as there is a bedroom above. The doors arent insulated at the moment. Any recommendation as to what solution I could use to cool/heat the garage ? Thanks!
-
-
- 12 replies
- 2.9k views
-
Who's Online (See full list)
- There are no registered users currently online
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·