The Shop
1,954 topics in this forum
-
Are the Shop Vacs that you can buy at the big box stores powerful enough to run a permanent (not portable) dust collection setup? I have the Oneida Cyclone attached to a shop vac now, and it really works quite well. It is a pain to roll it around the shop with me though. If I run 2" pipe around the shop with blast gates and a hose for each tool, am I going to be disappointed with the suction that the Shop Vac can produce?
-
-
- 46 replies
- 7.9k views
-
-
Well as mentioned in the wall sheathing thread I went back to HD to get the last of the $8 melamine they had on clearance. I ended up with 10 sheets, I'll do one long wall and an one end wall with the majority of these and save the last ones for shop projects. So, in all its glory, the shop as it was (I had already started moving stuff around, but after the last project it was left in quite a mess): And the progress over the weekend: Day 1 Day 2 Cutting in the hole for the AC unit (My dad pictured) Day 3 Built a small clamp rack And started working o…
-
-
- 10 replies
- 3.3k views
-
-
Got a dust deputy at an estate sale. No hoses or fittings. I have a rigid shop vac. I already use the Peachtree Dust collector. I have some new 2.5 inch dc hose and a pair of 2.5 to 2.25 inch converters from rockler. I am going to use the DD between the existing DC and the Rigid Shop vac. So, i have a horrible mix of connector sizes. Ifound solutions for the DC set up, but now I need to work with the DD fittings. The DD 1.965 IN/ 2.145 OUT. The hose I am using is 2.5 inch dust collecton hose. I can use a Rockler 2.5 to 2.25 converter to get it down to a difference between 2.145 outside on teh DD and then 2.275 on the inside. Is there any avalable fitting, pvc …
-
- 7 replies
- 16.7k views
-
-
Hey guys I just purchased a new dust collector. Its a two horse from Harbor Freight and am on the fence about what piping to use. PVC or Metal Duct, or what. Also how to properly ground is a big question I have. Please help. Thanks
-
- 2 replies
- 3k views
-
-
Hello All, as some know I completely re did my shop over the last year and after having several friends flood over the last six months I have been storing their home furnishings in my shop since it's climate controlled. It appears I will have my shop back to myself in about a month. So it's now time to finalize plans to build my cabinetry and such. I have a length of wall that is 32' that runs along my workshop. My plan is to run a countertop the entire length at 37" with an area for a chop saw and also a gap in the countertop for my drill press table. My conundrum is in the rest of the areas what percentage of storage do I want to be cabinets and what p…
-
-
- 2 replies
- 3.1k views
-
-
I recently saw a video for this: ..and it looked like that could come in very handy at times. Could work nicely as a in-feed table for multiple tools. Also to load/unload from a truck bed. I don't think I'll consider the Felder one, as it's around $1300, but I wonder if a lower cost lift table could be adapted with a wooden top with dog holes for not too much money. Looks like both HF and Northern Tool have some tables that could be used.
-
-
- 8 replies
- 3.1k views
-
-
I know there are already several threads dealing with insulation a garage, but I couldn't find an answer to my specific issue. I have a standalone 2 car garage that already has drywall inside, but isn't insulated. This is pretty common here, as our winters are quite mild, and most people use their garages for cars (strange...). The garage door is insulated though. There is no insulation in the attic space, but this is pretty easy for me to access and lay down some fibreglass insulation, but my question has to do with the walls. Is there an easy way to insulate them, short of taking down the drywall? Can you cut holes in the top and blow down some insulation? I…
-
-
- 8 replies
- 3.1k views
-
-
Hi everyone! I got either the Festool MFT/3 or the EZ-1 workbench for xmas, and now I just need to pick which one. I don't currently own a track saw, but am willing to add one to my workshop. I build a lot of boxes out of plywood and start with 4'x8' sheets. I don't own any festool equipment at this stage, but would like to slowly acquire some. I like the features of the MFT, but wish it could handle a 4'x8' sheet under the guide rail. The EZ-1 lacks some of the modularity of the MFT, but can handle a full sheet to crosscut. I can also use their baseplate with one of my current circular saws. I'd appreciate any advice as to which system…
-
-
- 6 replies
- 3.7k views
-
-
I recently started redoing my shop, after acquiring a giant bandsaw, and a ClearVue cyclone, it's time to do some serious stuff to make it cleaner, neater, and more badass! I had to build new brackets for the motor mount to hang the cyclone. I don't know how they can say you can install it on an 8 foot ceiling, unless you put in a 5 gallon bucket for collection I don't see it being feasible. The top of the motor is about 9' 2" from the floor. I have a 31 gallon heavy duty steel garbage pail. Brackets are made from walnut ply scraps, and 2x4s (super classy) I actually used maple edge banding on the walnut ply. Hanging this thing up is a huge challenge with on…
-
-
- 343 replies
- 47.4k views
-
-
How does everyone organize their shop / tools? Do you organize by use (marking, cutting, measuring, etc...) or by category (screwdrivers, clamps, squares, wrenches, etc...) ?
-
-
- 7 replies
- 3k views
-
-
I work in a cold, barely insulated shop. It's a 2.5 car garage, attached to the house, unheated. We are planning on using almost the entire thing for shop space. The garage door is 'leaky' and uninsulated. Since it's a rental house, modifying things to get some heat, even minimal, really isn't an option. It's currently 17f out here, and thats decently warm for this past week. I've read some threads on getting heat into a shop, but not much on what to be aware of in a cold shop. I know finishing will take longer to cure, if it even does. Same with glues and epoxies. I have a really nice face shield for turning on the lathe, but it fogs up so quick, I can't …
-
-
- 12 replies
- 3.4k views
-
-
I bought the Bosch 10" Glide on leap day and it's been sitting on my outfeed table since then and is ready to find a home. Here is the wall I have to work with for its location. My first preference is to do what Eric did and use it for an outfeed table for the bigger bandsaw and go where the router table currently is but there is an issue. Boards over 8' long on the table saw and jointer would run into the cabinet. I could rotate the TS and jointer 90º CW but then I would have to probably modify the DC ducting. I could have gaps in the MS cabinet to allow long boards to work. I would move the router table over by the small BS and also take the big BS off the mo…
-
-
- 40 replies
- 13.8k views
-
-
We are going to be moving into a new house in about a month and was able to get an oversized double garage available for my workspace. I basically have a greenfield to do whatever I want and before setting up the equipment from my last place, I want to ensure dust collection is put in place to avoid what happened in our old garage, dust everywhere. Been looking around and keep coming back to the Grizzly Cyclone Dust Collection. First, anyone have any good recommendations for dust collection for a garage and some tips in what I should be looking for? Secondly, does anyone have a Grizzly Cyclone system and are you happy with it? I'll also be looking to pick up som…
-
-
- 17 replies
- 4.5k views
-
-
I need parts from or a tail stock from a Yates large anyone know where I might come up with that?
-
- 1 reply
- 3k views
-
-
I'm going to preface this post with the fact that I am an amateur woodworking looking to expand into fine woodworking and expand the garage into more of a shop. So with that being said I have been using a workmate and just the standard kitchen cabinets as a workbench, I'm on a tight budget and do this as a hobbyist almost part time income. I have a design for a bench and I have a few questions about the top slab: Should I build a large flat top or a split roubo design? Would dimensional SPF lumber be solid enough for me to use as a half decent bench until I can zero in on a bench design better suited for my specific needs later on. Essentially I am planning on…
-
-
- 16 replies
- 3.9k views
-
-
I would like to hear about heat and a/c loss from people that direct vent their dust collector. The dc will be running for hours at a time. I would like to vent outside, but I want a climate controlled environment. I found this in another thread. Well I never run it for super long periods of time. Since its been cold I haven't run it longer than 10 minutes and noticed the air got a little cooler but nothing that would make me regret my decision. I have a 5000w electric ceiling heater. It is totally worth it for the increased performance, cleaner air and noise reduction. I can deal with a bit of a temperature drop. In my previous business, either the planer,…
-
-
- 15 replies
- 3.7k views
-
-
As much as I would like to have built a Roubo I have decided to take the "buy it" route. I decided on the Sjoberg 2000 Elite with the cabinet. Woodpeckers has it on sale with free shipping. I feel like I need to apologize for buying vs building I was watching Marc's video where is said the skills he learned when building his Roubo will most likely never be used again. Obviously the pride I would take in the accomplishment would be sweet but in the end lazyness won the day Maybe one day ... or perhaps I can retro-fit that sweet benchcrafted leg vise on to the Sjoberg... hmmmm
-
-
- 51 replies
- 12.9k views
-
-
Hi, I'm looking for a thickness planner and I'm pretty stuck between Makita and Dewalt or a budget Triton. I will be doing my woodwork in a spare bedroom, so I guess dust extraction will be key. I will mainly be making furniture out of reclaimed wood. I'm really stuck between the Makita and Dewalt but also wondering if the Triton is worth a look as its £200 cheaper. Triton TPT125 Planer/Thicknesser, 317 mm Makita 2012NB 240v Portable Planer Thicknesser DeWalt Dw733 230V Portable Thicknesser 1800W Does anyone know the pros and cons between the above? Many Thanks Luke
-
-
- 4 replies
- 3.9k views
-
-
I just semi-retired in N. Idaho after working 30 years for a large lumber manufacturer who moved me all over N.A. I set up small shops in garages and basements and now have a 30x40 heated shop! I have been spending the last few weeks getting things set up and only have the new Clearvue dust system to install. Hopefully I will be building furniture again after a 4 year hiatus from woodworking!
-
-
- 26 replies
- 7.7k views
-
-
It has been a while since I posted anything about my shop. Aside from a pic of the liquor cabinet I have been really quiet lately. Just busy!! I took this pic the other day, and it just landed like this... In no way is this meant to be a Festool love fest or bashing... I will add pics as I clean up the rest of the space. Here is where the magic happens.
-
-
- 31 replies
- 7.3k views
-
-
Does anyone heat their shop with a vent free gas heater like this? If so does it create excess humidity? http://www.northerntool.com/shop/tools/product_200664873_200664873?utm_source=Email&utm_medium=NOS&utm_campaign=bluecore&utm_content=tm&om_mid=&obem=M_JrUNnSLos_iABhJktj367nLGjO6ROg54qzgpV01Kg%3D
-
-
- 19 replies
- 4.5k views
-
-
Afternoon, If this is alright with the mods... Here is where I'll keep you all up-to-date on my shop build and the ideas I'm debating. As I stated in my intro message that i have claimed the garage as my shop space. the building is a detached 22' x 24' two car garage with 9ft ceilings and a modest attic space. it has its own power meter and the previous owner wired it using all 20 amp circuits. Im facing some lighting and wiring issues as i rehad the space. since i'm a tech guy professionally, Ill wire it for network as well as power and cable. I already have plans to add-on to the back of the building. in the mean time I'm looking at bui…
-
-
- 17 replies
- 4.3k views
-
-
Been thinking about buying one, the typical style like this: Would be easy enough to make, I guess.. Are there any features worth including in a shop design that are omitted here? Not really interested in the spindle sander feature, as I have a ridgid combo dealer-wacker. What do you guys use? Do you like it?
-
-
- 26 replies
- 9.7k views
- 1 follower
-
-
I just finished installing the oneida v3000 3hp dust collection system in my 40x20 shop. The only problem is that I don't have a remote. Oneida says that they can sell me one for $35, but I feel like there must be a cheaper solution. Any ideas? If possible, I would like to order off of Amazon. Thanks in advance, Josiah
-
-
- 6 replies
- 3.1k views
-
-
How do you guys like to organize screw/nails and other little items in your shop? I don't have a lot of drawers right now, mostly just a messy stack of little boxes inside cabinets, and it's time to fix it... I am mostly talking about 15-20 different kinds of screws/nails/washers and other similar sized items that come in little cardboard or plastic boxes. I like the idea of little 'drawers' like this kind of thing, because it allows you to organize and quickly get at things, but it takes up valuable counter space I don't have, and is the least mobile solution in the world. I'm not a tradesman for a living, but I do bring tools over to friends/family's homes somewh…
-
-
- 27 replies
- 10.8k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,010 Total Members
- 3,644 Most Online
-
Lolli4 Newest Member ·