Product Reviews
Read and share firsthand reviews of woodworking tools, accessories, and supplies. Find out how products perform in members’ shops before you buy.
269 topics in this forum
-
I got the WoodRiver 12" Combination Square from Woodcraft for $30 and the first thing I do is check to ensure it is square. I strike a line, flip it, and it's not square. In disbelief i repeated the process at least 5 more times and got the same results. When I get back from my trip to New Jersey and New York I will be returning the square. Other than it being out of square it seemed like a well made tool. I hope that it is just a lemon and the majority of their squares are, in fact, square. I know that some people will say you get what you pay for but I have a Combination Square that I got from Harbor Freight for around $10 and that is perfectly square. I just want…
-
-
- 27 replies
- 18.6k views
-
-
I am relatively new to woodworking...and still putting together a decent set of tools. Trying to come up with a list of good online suppliers too...it's hard. I can tell there are "brand whores" in this field as with any other...heck, my Dad refuses to buy "any yellow tools". I'm more interested in quality than price...but not interested in top quality either...I guess middle of the road. Not to bad mouth Harbor Freight, but the couple of times I've looked there to buy something I've opted out because it just doesn't seem like the quality is there. What do you buy from Harbor Freight?...What have you had success with?
-
-
- 73 replies
- 23.3k views
-
-
for a while I've been searching for a plywood optimizer for my mac computer. all i came up with was programs for PC. I could have purchased windows, then used bootcamp to run windows on my mac. that was going to cost money and take time. i continued to say to myself, "there has got to be SOMETHING out there...." after google searching i found iOptiCut. i give this app 4 out of 5 stars. 5 being the best 0 being the worst. the app costs $8.99 it works on ios 5.0 or later. Doral Design (developer) says it works in english and german. i downloaded it while using ios7. the first thing you do is create a new item, by touching the plus sign button. you then se…
-
- 5 replies
- 4.5k views
-
-
I just got one of these because I needed another small mortiser to cut a few hundred 1/4" x 3/4 x 5/16 deep mortises and have another mortiser set up dedicated to cutting larger mortises. It will work fine for this purpose, and pay for itself with this one job at something like $230 shipped. There are several other brand names on this same machine, so look closely before you buy one of the ones like this. I wouldn't recommend anyone buy this machine as your first or only mortiser. It holds the chisel and bit just fine, and cuts a precisely positioned and pretty little mortise, but the adjustments leave a lot to be desired if you need to change the mortise positi…
-
- 0 replies
- 4.6k views
-
-
A few months ago I did a review on the veritas jointer plane, and I promised that I would follow up with a review of the accompanying, optional, jointer fence. I have owned this plane for a few months now, and have completed a few projects with it. The fit and finish of the fence are, not surprising, excellent. The fence comes with knurled brass knobs which are threaded to fit into the body of the plane. There is a set screw to square the fence to the plane body. This operation can be a bit finicky, but once you get it set, it's holds it setting pretty well and only needs a minor tweak once and a while to keep it square. The fence also has two threaded slot to st…
-
- 4 replies
- 5.4k views
-
-
Hey there! I wanted to share my experience with the Abranet sanding discs. Shown here: http://www.woodcraft.com/product/2005922/35322/mirka-abranet-5-assortment-pack-35-pack-.aspx I bought the kit and the thick "interference" pad, and the protector pad from Woodcraft. The interference pad is mainly used for sanding near the edges of the board. The pad protector is used to attach to your sander to keep from wearing out the hook and loop on the sander. This pad protector is essential to the sander because of how thin the sanding discs are. I am very impressed with the quality of these discs. First, they are very resilient to clogging like normal discs are. They …
-
- 0 replies
- 3.2k views
-
-
This is my first tool review, so bear with me! I've only cut a couple of sets of dovetails with the jig, but enough to give an overview of set up etc. Until now I've not attempted cutting dovetails in any other way, with power tools or by hand. This is a review of the Craftex CT052 dovetail jig. It is designed to accommodate pieces up to 12" in size. I got mine on special offer from Busybee Tools for $80 (+tax) CAD. The Craftex CT154 can go up to 24" and is available for $189 (+tax) CAD, although at the time of writing there was a $20 off sale. Both these jigs allow you to cut both pins and dovetails at the same time on the same pass. Some people online ha…
-
- 0 replies
- 8.9k views
-
-
Quite simply, these things are awesome!!! I just got some of the extreme fine cut ones on sale at Woodcraft. Even these x-fine cut ones cut fast, and leave an amazingly smooth finish. I like them so much, I'm going to order the ones that I didn't get. Woodcraft has a video too on them. I got the plane float ones from Lee Valley, and probably won't bother to sharpen the ones that do the same thing that came from LN again. http://www.woodcraft.com/search2/search.aspx?query=iwasaki%20japanese%20carving%20files
-
- 4 replies
- 5.9k views
-
-
Hi all, in the thread P.B. asked about the DRO for the table saw, I learned about this tool for the first time. It seems like a good addition for me so I bought one at Roclker when I was there on Friday. I installed it over the weekend and it was an easy job. I have an older PM66 and though I had to replace the scale and make a new alignment window for the rip fence, my eyes are not as young as they used to be so when I learned about the DRO, I had to have it. First, after it was installed, I was a little let down by the X.XX readout, I am used to three dec. points. The specs for the readout gives it a 0.002 accuracy per foot. I have 48 inches to the right of my b…
-
- 10 replies
- 8.5k views
-
-
My sander died a few weeks ago (in the middle of a project of course), so I brought it in for a repair. After a day, the tech called me and told me that ridgid no longer makes my sander (r2600). Because ridgid cannot repair the tool, they said they would send me a replacement. A week later a refurbished r2601 arrives from FedEx. I take it to task right away, and I was dissapointed with the unit. First, it does what it is supposed to do. It sands and orbits just fine, and the dust collection is quite good when using the dust deputy. The issue is that I feel ridgid "cheaped out" when designing this sander. Many of the features that I chose the previous model for …
-
- 4 replies
- 6.3k views
-
-
Let me start this review by stating that I have never been a "shop apron" guy. I would leave my stuff all over the place, and play the game of " where did my gauge, tape, square, etc. go?" This apron was expensive, at about 40 dollars cdn. I was unsure about it,but I know lee valley are superb with returns, so I didn't sweat it. If I didn't like it, I knew I could return it no problem. Upon trying it on, I found it difficult to adjust. Not because of poor design, but because of my own newness to the apron. After fiddling and swearing, my wife finally showed me how to adjust it properly. The apron has quick adjust clips on the nylon straps. There is also a quick…
-
- 5 replies
- 8.3k views
-
-
One of my 15 year old Porter Cable heavy duty trim routers died and they do not make them anymore. So I did a little research and decided to get the Dewalt 611. It's a pretty nice tool. Variable speed, soft start, low noise and plenty of power for its size. Low center of gravity makes it less prone to tipping on narrow edges. The base is nicely shaped to fit your hand with a curved flare that helps you steer and stabilize the bit as you go around corners. The 2 LED lights improve visibility,I was routing black laminate all day today! My only puzzle is the clear base. It does not slide as smoothly as the phenolic base on my Porter Cable or Festool trimmers. I have made m…
-
-
- 5 replies
- 4k views
-
-
Well I finally broke down and bought one of these planes. I have been doing more and more handwork lately, and decided to go for it and get a nice jointer plane. I selected the veritas based upon the quality, price, and availability. The only other real contender for me was the LN, but I could not actually touch it before ir bought it. I have to get a tool in my hands before I buy it, and this was quite easy with lee valley being in my area. When I went to lee valley to purchase this plane, I opened it before buying it. I noticed a small imperfection (looked like a pit, but I couldn't be sure) in the sole, and the salesperson immediately gave me another plane. I …
-
-
- 6 replies
- 9.6k views
-
-
So a couple months ago I grabbed a previously opened can of Arm-R-Seal off my shelf to finish a project and wouldn't you know it, it had cured in the can. So I decided I'd order some Bloxygen. I had my doubts as to weather or not it would be worth the money. I've been using it for a couple months now and have had so much as a skim coat inside the can, but that's usually the case for me if I just make sure the can is sealed when I'm done with it. So, the other day I had some Arm-R-Seal in an open secondary container that I was using to finish a project and I thought I'd do a little experiment with the left over finish. I had enough finish left in the secondary contain…
-
- 0 replies
- 3.2k views
-
-
There are many different accessories similar to this one but I decided to buy this to check it out. Google it to find out how much it costs in your geographical location. This accessory is offered by Dewalt to enable the user to drill and counter sink holes and then tighten up screws without having to use a different drill or screwdriver attachment. I had about 400 pozidrive #2 head screws to put into a project I was building and didn't relish the task. Either I had to buy another drill or get a quick change head. I opted for the latter. The device comprises: A main drive holder with a hex drive shank that fits into the drill chuck. It has a socket which takes t…
-
-
- 1 reply
- 6.8k views
-
-
Now that I have had some time to really break in my purchases from Grizzly, I feel I can offer a good semi-review on the tools from what I have encountered. The two tools I purchased are the G0715P 10" Hyrbid Table Saw, and the G0656P 8" Jointer. First off, these are the first machines I have purchased for myself. I have used a jointer and table saw before, but these are much of an upgrade from those. I wanted to start my own tool collection, and since I had the space to do so, I ordered as big and nice as I could afford. I was skeptical of ordering from Grizzly at first because of the numerous bad reviews that are available on the Internet. I did find good review…
-
- 8 replies
- 30k views
-
-
So I was at Lowe's to get some sandpaper thinking it sure would be nice to have a oscillating spindle sander. I picked up what I needed and saw this: http://www.lowes.com/Search=gator+drum+sander?storeId=10151&langId=-1&catalogId=10051&N=0&newSearch=true&Ntt=gator+drum+sander#! I'm working on a rocking horse for my daughter, the charity build one, and there are some curves that need sanding. I though for $8.98 I'll give it a shot. Really it was $18.96 because I got both sizes but who's counting. Got it home, put it in the drill press, bent some wire to hold my shop vac hose near the drum and started to sand away. It worked pretty good and save …
-
- 2 replies
- 4.1k views
-
-
This past winter I was asked by my lovely lady to build a window seat for our front room. We decided on a design that had two drawers and cabinets on the ends. Not having ever built cabinet doors before I spent entirely too much time reading about it and then decided I just needed to buy some bits and try it. As I didn't have any plans to make too many doors this style I didn't really want to invest in a really nice set of bits. I decided to go with the rail and stile set from PrecisionBits. I bought my set through amazon..because I was feeling lazy and didn't want to enter my info again. I liked the fact that they are multi piece bits so you have the opti…
-
- 1 reply
- 2.9k views
-
-
We love our Tormek T-7. Since we purchased one of these from Axminster late last year, we have been blown away by its ease of use and excellent results. As a Joinery company based in Chester (UK), having sharp chisels and plane irons is a must. We use these tools on a daily basis, whether it being for cutting in hinges for doors, installing locks, joining wood, or planning, we have to make sure they are all in top form for each job we undertake. Up until purchase point, our preferred method was with a honing guide and wetstone. Now I’m not saying that there is anything wrong with this method, and i know that you can achieve much sharper results by hand, but for us…
-
- 8 replies
- 7.9k views
-
-
Ill start off saying this is one of General finishes pro products. I dont know why they keep it in that product line other than the fact that they offer predetermined formulas. Personally Id love to see this stuff on the shelves at places like Rockler and Woodcraft. The stains can be sprayed NO wipe or wiped either way is fine. Sprayed the colors are more solid and work better on blotch prone woods like poplar. Mixing is as easy as it gets. The formulas use the part system. Parts can be any liquid measure for example cups, 1/2 cups, ounces, milliliters it really doesnt matter what you use. The system is very consistent so if you need more of the same color your safe to …
-
- 2 replies
- 5.9k views
-
-
Ok not really tools but while pre finishing cabinet interiors this morning I thought I'd post these handy helpers. Stainless steam pans are great for stains. These come from Costco type stores. These came from cash n carry. Cost is very low the pans sell for $2 lids $4. Stainless ladles are $2 for 1oz. They come clean real easy and stay looking new, even pva glue just peals right off. The best part is your not stealing from the kitchen so the wife stays happy.
-
- 3 replies
- 2.9k views
-
-
I thought I would post a quick kudos to Rockler for bringing Fillon mixing lids to the masses. These lids have been around for quite a few years but were a commercial product used by finish mixing systems in the woodworking and auto body industry. So far I have about 25 and all are in perfect working order and are well used and a few years old. The lids make a good tight seal to the can on all sizes. They dont really need any cleaning other than a rinse in the sink with water based finishes. For solvent based they clean up easily with very dilute thinners. I just took some quick pics. You can see the black finish running down the side of the can. This was from pouring t…
-
- 6 replies
- 4.3k views
-
-
I bought one of Woodpeckers one time tools at the IWF this summer. 6" wrap layout tool has a 3/4" leg to let you mark the top and side of a board. The middle of the tool is full of holes every 1/32 to draw lines down the edge of a board. You put a mechanical pencil in the hole and it let's you mark accurate lines very quickly down the length of a board. It has become an instant favorite layout tool. I used to set several small squares for repeat marking of specific lengths . Now I just have to pay close attention to which hole I put the pencil in. I have had one of Veritas wrap squares for ages but this one is much more versitle . I think it has added a greater accu…
-
- 5 replies
- 5.8k views
-
-
So I ran the trimmer all day with the horizontal baseplate and I am quite impressed. Slender motor profile is easy to hold. Knob on the baseplate is placed for effort free control. I tried to tip the bit into the edge on some test pieces and it is possible but not easy. Depth adjustments are very easy and 1/256 th of an inch change is actually possible. Once I got the cut set the way I wanted it stayed put for 6 straight hours of trimming. The wide footprint of the baseplate helps with accurate trimming of narrow ends. 120 edges on 30 panels x 2 ends each = 240 5/8" wide ends to cut and never nicked or scratched the laminate! Is this a tool for everyone's shop? May…
-
- 8 replies
- 4.9k views
-
-
Forgive me if this is covering old ground but I have just finished the book "Workbenches from Design & Theory to Construction & Use". I really enjoyed the book and found it good value and very informative. I put the full review on my blog . I have only really ever worked from a bench like this (dad working on some stair strings). They have always been great for large scale work that we do and power tool work. However I have found them lacking of late when working on my own projects using hand tools. So on the horizon a Schwarz inspired "French" bench. Have any of you read the book and what are your thoughts? Did you make a carbon copy of the benches within or …
-
-
- 21 replies
- 5.9k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,011 Total Members
- 3,644 Most Online
-
bobtjanitor Newest Member ·