Project Journals

2,401 topics in this forum

  1. Another Drill Press Cabinet

    By gee-dub,
    • 6 replies
    • 4.9k views

  3. Shadow Box Frame

    By gee-dub,
    • 15 replies
    • 4.5k views

  4. cutting boards

    By curlyoak,
    • 7 replies
    • 3.3k views

  5. Modern End Tables

    By Chestnut,
    • 18 replies
    • 4.2k views

  6. Quarter sawn white oak pedestal

    By curlyoak,
    • 14 replies
    • 4.2k views

  7. A walnut wall unit for a home office

    By curlyoak,
    • 8 replies
    • 3.2k views

  8. Three 8x10 Frames

    By gee-dub,
    • 8 replies
    • 3.1k views

  9. Epic shaker blanket chest 1 2 3 4

    By mdbuilder,
    • 82 replies
    • 18.2k views

  10. Scott Lewis Cutting Board

    By gee-dub,
    • 10 replies
    • 5.5k views

  11. Simple mirror frame 1 2

    By wtnhighlander,
    • 25 replies
    • 7k views

  12. Bathroom Remodel 1 2

    By Chestnut,
    • 33 replies
    • 10.7k views

  13. Memento Display Shelf 1 2 3 4 8

    By wtnhighlander,
    • 178 replies
    • 31.8k views

  14. Walnut bathroom 1 2

    By curlyoak,
    • 32 replies
    • 9.4k views

  15. Master Bedroom King Bed 1 2

    By Chet,
    • 45 replies
    • 9.4k views

  16. Mid Century Modern Couch, Draper inspired 1 2

    By Bmac,
    • 42 replies
    • 10.9k views
    • Bmac
    • Bmac

  17. FWW / Epic Woodworking Shaker Chest of Drawers 1 2 3 4 6

    By mdbuilder,
    • 149 replies
    • 28.9k views

  18. Quick Project - Bassinet Stand

    By JohnG,
    • 17 replies
    • 3.9k views

  19. Mini Hay Wagon

    By rarefish383,
    • 11 replies
    • 3.6k views

  20. Small Desk Build With Epoxy 2nd Project!!

    By twolip,
    • 3 replies
    • 3.3k views

  21. Quartered white oak bedroom. 1 2

    By curlyoak,
    • 30 replies
    • 9k views

  22. Another camper enhancement

    By collinb,
    • 0 replies
    • 3.2k views

  23. Stickley Console Table

    By Evans_Woodcrafts,
    • 20 replies
    • 6.9k views

  24. Another Granddaughter in the Shop

    By Chet,
    • 10 replies
    • 3.6k views

  25. Cherry Wall Cabinet - Completed 1 2 3 4 5

    By JohnG,
    • 118 replies
    • 29.3k views

  26. Shower Bench

    By Chestnut,
    • 15 replies
    • 4.9k views


  • Topics

  • Posts

    • Coop
      Slow Server?

      By Coop · Posted

      I’ve briefly known folks that get their jollies by pissing people off.
    • Ron Swanson Jr.
      Slow Server?

      By Ron Swanson Jr. · Posted

      What a sad state of affairs the Internet has become. Can't even have a tiny, harmless little WW forum without it being constantly attacked. What could there possibly be gained from harassing this forum???
    • Beechwood Chip
      Slow Server?

      By Beechwood Chip · Posted

      WTO was down briefly at 5:53pm Eastern.  I emailed Marc, and now it's back up.
    • Von
      Von's shop tour and setup log

      By Von · Posted

      [Oops, this post was supposed to go in my workbench journal.] Flush cut my pegs and cleaned up the glue squeeze out from the long rails. I noticed a couple of the pegs broke below the surface so I applied a little wood putty to smooth things out. Started on the shelf. I'm sandwiching two pieces of plywood under and over a cleat to make a void I can fill with, e.g., sand bags if I decide I want more mass.  Chance to break out the pinch rods. I added a 1/16 shim so I'd have a little play and also moved the rods around to find the tightest spot. The rod just moves right over to the table saw, without the shim, to set the fence and cut the shelf to width. For the shelf length, I used a tape measure since my rods are not long enough. Less fun but good enough. I cut the shelf to length (45") with the track saw. I cut the corners to fit around the legs with a Japanese pull saw and did a little shaving with a low-angle block plane where the plywood was too tight. Bottom of shelf fits. Top part and cleats to follow tomorrow.  
    • Ron Swanson Jr.
      What did you do today?

      By Ron Swanson Jr. · Posted

      Yesterday was my day to host the meeting for the box Makers SIG that I'm part of. I was to give a demonstration on hand cut dovetails.  I have never done that in front of an audience. I learned there's a pretty big difference between peacefully working alone at my own speed,  And trying to go fast through the process with 5 guys literally standing over my shoulder.  Still a good meeting and enjoyable time with a good group though.   

  • Popular Contributors