Project Journals
2,359 topics in this forum
-
- 11 replies
- 1.2k views
-
- 139 replies
- 14.6k views
-
- 9 replies
- 1.3k views
-
- 39 replies
- 5.6k views
-
- 13 replies
- 1.5k views
-
- 25 replies
- 5.2k views
-
- 4 replies
- 1k views
-
- 14 replies
- 2k views
-
- 50 replies
- 9.6k views
-
- 14 replies
- 1.9k views
-
- 49 replies
- 4.8k views
-
- 14 replies
- 2.1k views
-
- 2 replies
- 1.7k views
-
- 22 replies
- 3.8k views
-
Kym's Table 1 2 3 4
- 77 replies
- 12.4k views
-
- 22 replies
- 2.1k views
-
- 4 replies
- 1.5k views
-
- 14 replies
- 2.2k views
-
- 22 replies
- 2.4k views
-
- 17 replies
- 2.6k views
-
- 135 replies
- 20.2k views
-
- 4 replies
- 1.1k views
-
- 22 replies
- 1.7k views
-
- 35 replies
- 3.3k views
-
- 61 replies
- 7.9k views
-
Who's Online 5 Members, 0 Anonymous, 50 Guests (See full list)
-
Forum Statistics
31.2k
Total Topics422k
Total Posts -
Member Statistics
23,773
Total Members3,644
Most Online
-
Topics
-
-
Posts
-
You have made some wonderful progress on your space Von. I have really enjoyed getting to tag along so far. Thanks! -
Yes. They look good but are of course 4" square corner and I want 3-1/2" 5/8" round corner . I have a feeling that with the small pantry hollow core door one hinge may do the job. They come as a pair so I may give them a shot and just do a little chisel work. Thanks all!
-
I usually favor figure 8 connectors or shop made "buttons" to secure tops. I've had some Z clips in stock for years and thought I would use a few. Even though there is an attachment point at each corner, people like to lift things by the tops so I will add 3 more connection points. I chuck up a slot cutter and set the height. I clamp a block of wood to the member to be cut to give me a greater bearing surface for the router base. A none-too-specific length slot gets cut on each upper drawer divider and one at the back rail. Between designing the dressers and getting them installed we decided to go with plantation shutters for the windows. The dressers were going to be a smidge taller than the lower ledge of the window frames. With the addition of the shutters these dimensions changed. Time for everyone to get a little shorter. I'm going to use the guided circular saw for this. I found that using a pair of rail connectors gives me a more solid pair of guide rails. One on one side . . . . . . and one on the other. YMMV. I find yet another use for the cabinet door holder jig thingy. And presto. Everyone is an inch and a quarter, shorter. And I'm a poet, and didn't know it . I re-profile the bottoms of the feet and I'm ready to move on. I was worried that this leg shortening would blow the look. I did a "what if" test in Sketch Up before committing and we decided it was OK.
-
If you see what looks like a plug for a hole on the wrong end of one of the cleats, that's a jpeg artifact :-) Not worth covering most of my process since it's the same as gee-dubs, but I will capture the way I figured out to drill the angled holes on my drill press table. -
By Beechwood Chip · Posted
No, I left them up a smidge and then tighten.
-
-
Popular Contributors
