The Shop
1,954 topics in this forum
-
So my options here... some info ... garage door is on south wall. House entrance and back patio entrance on are west and north walls. On both setups I will still have 8-10’ behind me before I hit the miter saw cabinets or the house door. Then another 10ish feet before I hit my east wall. 1) 2) my thoughts on both ... option 1 Moving a sheet of ply would be easier outside than inside the garage. Although not too sure how much that would happen after I build the cabinets and outfeed and assembly tables though. Option 2 once past the basic shop stuff I could cut while the garage door is closed. Kee…
-
-
- 11 replies
- 4.1k views
-
-
What a great community this is. I've enjoyed quietly reading others posts over the past year! I put up a new wall in the basement to begin a dedicated shop setup. Its time to hang a door now. Inside the shop I have ideas on where machines will be going but not finalized. Outside the shop door is the HVAC and water heater in an unfinished area. I'm thinking for safety reasons that the door should swing outward into the utility area rather than into the shop. The door does have a window in it. Is there any other considerations that I'm not thinking of?
-
-
- 9 replies
- 3.1k views
-
-
I have just discovered this forum and joined earlier today. Looks like a great group of woodworkers. I've seen a few other posts about new shops and I thought I'd post mine as a way of introducing myself. I've been working wood since I was a kid, so I think I've got 50 years of it under my belt. After 35 years in a 24x24 foot shop, I built my dream shop at our retirement house. Started two years ago, and moved in last year. Finally got time to make some sawdust over the past couple months. I retired 6 months ago and moved down here full time. I have other hobbies that take up a lot of my warm weather energy, so winter is my prime time in the wood shop. The sh…
-
-
- 24 replies
- 5.9k views
-
-
So my pink foam spray booth has served me well but it might be time for a better solution. On bigger items the current booth and box fan behind isn't enough to pull all the overspray away. I know the ideal solution would be to build a finish room but that isn't going to happen so my current thoughts are a curtain-type solution. The vapor barrier I used for the insulation is fairly think but I would have to find a solution to hang it from the ceiling since it doesn't have grommets - maybe they're easy to install? Putting up and taking down would take a little time but probably not bad. A sliding U-shaped curtain would be really nice but I don't have any clue on prices and …
-
-
- 11 replies
- 10.9k views
-
-
Hello everyone. I'm new here and my wife and I just moved into a new house and I actually have my own 12x15 shop here which is a huge upgrade from my old shed where I had to pull everything out of the shed to use one tool. I know it's small but I'll be using lots of casters. I'd also like to preface my question by saying woodworking is strictly a hoppy for me at this point but would like to continue growing and learning and upgrading. Below is a list of what I currently have..what do you guys think I need to add or upgrade to have a well rounded shop. I'm not looking for top of the line equipment but I am looking for mid range tools that get the job done and last. …
-
-
- 11 replies
- 3.2k views
-
-
I work in a garage and when I sand I have a lot of dust in the air. What is the best way to get rid of that in the air? Can I buy those exhaust fan (the ones that have two fans) and mount that on a window? Would an air filter system work better? I am on a pretty limited budget.
-
-
- 12 replies
- 5.5k views
-
-
I recently went back (Waaaaay back) and listened to episode 3 of WoodTalk when the subject of soundproofing and noise control came up. While there were some good suggestions on the show (and in some other threads here), most of them are geared towards trying to keep the noise confined within the shop. Another step that might prove helpful is to try to dampen those pesky dBs at their source (i.e. the machines producing them). There's products from the automotive industry that very effective in reducing ambient road noise from tires, exhaust, engine, wind, etc. One such product is Dynamat which comes in a peal and stick application. You could line the machine cab…
-
- 5 replies
- 4k views
-
-
Mr Wilmots is at it again! I like this...I was less than halfway thru and I realized it did too much already though, haha! It;s pretty cool, worth the watch, and maybe worth building your own if you have a small shop like me. I have a frankenstein'd thing built from a motorized standing desk that does about half this stuff, when it dies I may replace with this...but it's tempting to replace it sooner than later He sells plans here, fyi: http://benchworks.be/en/projects/mfsc-multi-function-shop-cart/ . I've used his plans for other projects before, they are top notch.
-
-
- 5 replies
- 4.4k views
-
-
Was thinking about this and trying to find ways to save a little money since I will be needing quite a few. from Jay Bates miter station build ... no backs on them. I was curious if this is an acceptable way of building shop cabinets ... or even adding like a 1/4 backer on the to just keep the dust down to a minimum if needed. Or should all 3 sides have 3/4 pieces? (sides and back) If you just put the cross supports like he does that should help give them enough stability not to rack or collapse right?
-
-
- 38 replies
- 10.9k views
-
-
I work in a garage and when I sand I have a lot of dust in the air. What is the best way to get rid of that in the air? Can I buy those exhaust fan (the ones that have two fans) and mount that on a window? Would an air filter system work better? I am on a pretty limited budget.
-
- 2 replies
- 3.2k views
-
-
Hello, So my workshop is in my garage. I do a lot of sanding and some staining and finishing. In the garage is the furnace and water heater. Is it dangerous to be sanding near this appliances? Nic
-
- 13 replies
- 9.7k views
-
-
I have decided to buy an overhead type air cleaner. The question I would like to run past you folks is whether two small units would be better, worse or the same as one larger unit. I am into wood turning now,. I do have masks for use when working, but turning generates copious dust which migrates and settles on everything. So I admit my first goal is keeping the place cleaner, but keeping my lungs cleaner is also important. I also put a premium on quieter operation. I had done some research including other posts here and a older Fine Wookworking article on the topic and had settled on the Jet AFS 100B. I have been waiting for a 15% sale to pull the trigg…
-
-
- 25 replies
- 13.1k views
-
-
I have a 18'x22' shop. I'm at the point where I want to run rigid ductwork to all of my tools (table saw, jointer, planer, band saw, miter saw, and a few more things in the future). I currently have the Harbor Freight 2HP dust collection with a Wynn filter on it. It works fairly well connected directly to each tool. One thing to note is that I only have 120V in the shop. I'd like to avoid getting 220V if possible because it would be an expensive install (my shop is an old recording studio with some fancy sound proofed walls). I'm considering a few options: Keep the Harbor Freight 2HP dust collector and add a Super Dust Deputy cyclone. Cost: …
-
-
- 26 replies
- 17.6k views
-
-
In the videos he builds the top first then the bottom. Why? He still had to shim up the saw horses and all the to get it level and also mill up some 2x4s ... would building the base first cut down on some of this? Or no?
-
-
- 11 replies
- 3.7k views
-
-
-
Feels like there have been quite a few of these throughout the summer, but I guess this one has the twist of being for a new woodworker. So we moved in late May which feels both like it was yesterday and ages ago really. and the 2 car garage was always to become a shop. A sub panel will be needed and will get installed in the coming months depending on the electrician's availability. here's the "room" layout (ceilings are about 8 1/2 feet) There isn't a tremendous amount of wall space as you can see with the 3 man doors, the 2 garage doors and the fairly large window, but at least there is A) a room, which is already pretty good , B) good amount of li…
-
-
- 13 replies
- 4.8k views
-
-
On a current, large, complicated standing seam roof job, I bought one each of every different kind of HT (high temperature for metal roofs) membrane I could find. All are okay, and some really expensive. For the best combination of price to quality of product, this one is my current favorite. It's almost a hundred bucks per 200 sq. ft. roll cheaper than the Grace product. The Grace product is my favorite as far as quality goes, but this one seems to be the best value. It's going under the rest of the roof that isn't covered by the various different types I've used so far. http://alco-products.com/products/underlayments/alco-shield-high-temp.html I put thi…
-
-
- 16 replies
- 4.1k views
-
-
So I'm finally at the point to where I don't have any major projects going on and I am now spending the next month doing a complete overhaul of my shop space. I'll be installing lumber storage racks (vertical and horizontal), ceiling mounted storage (for some of the household things that take up space throughout the year), and modifying an 4'x8'x12" cabinet that is just holding old junk right now to be an organized tool storage space for hand tools and small power tools. Oh, and I'm going to put together a charging/storage station for my cordless drills/tools, as well. I'm curious what fixtures you have made for your shop that you have found to be handy? From …
-
-
- 32 replies
- 12.9k views
- 1 follower
-
-
Or, "yet another new house, new shop thread." After living in apartments for three years, I finally closed on a house last month. With part of the basement walled off for mechanicals and the like, I have just shy of 400 square feet with an 84" ceiling to dedicate to making stuff. What tools I own are currently piled in a mound in said basement. Electrical needs a panel upgrade, dust management will be a priority after that. Yada yada. It's going to be a long road making this space my own.
-
-
- 18 replies
- 5.1k views
-
-
I'm in the process of getting my shop set up and was just given a Shop Fox 1.5HP, dual port dust collector with 1 micron bags, some 4" hoses and a bunch of blast gates. I'm still trying to understand the best way to manage dust in the shop (dust collectors, dust extractors, separators, filters, microns !?!?!?!?!?!). I was just reading about cyclone dust separators. Is this something I should consider adding on to my collector as a first step in managing dust? Any advice on how to get the most from my dust separator would be very appreciated? Here's a link to the exact model I have. http://www.northerntool.com/shop/tools/product_200481385_200481385 Thanks again for a…
-
-
- 12 replies
- 4.5k views
-
-
While the shop vac works *generally* I'm running into something where, I suspect, even a heftier vac might fail. It seems my table saw piles up the dust inside the cabinet. I just cleaned it out Sunday and was disappointed. Could that be because the side panel has enough air leakage so that airflow to the outlet is reduced? Lots of dust is extracted but too much remains and piles up in the corners.
-
-
- 10 replies
- 4.7k views
-
-
I have two cyclone separator/shop vacuum combinations working in my garage wood shop. Why two? I added thesecond separator set-up rather than run vacuum piping to serve all tools - wanted to avoid piping, blast gates, etc. I have a table saw and a router table running on one and a stationary belt sander, drill press, and small jointer feeding the other. The first is a 2HP Genie and the second is a 4.5HP Shop Vac; both have 2" hose running from tool to cyclone port and from cyclone to vacuum. The older Genie set-up passes virtually nothing to the vacuum (99.9% gets collected in the bucket under that cyclone.) My new Shop Vac system is constructed exactly the same, ho…
-
-
- 30 replies
- 12.5k views
-
-
I live in an apartment so I have a membership to a shared workshop to use the jointer, planer, table saw, etc., but I'd like to start doing some of my hand tool work, final fitting, sanding, and glue-ups at home. The glue-ups I can do anywhere but I'd really like a way to hold things securely for the planing, sanding, and the like. I'm mostly building end tables, nightstands, and things like that. I have a patio where I can work as well as some spaces I can set up in temporarily inside, but I need something I can transport in and out and that doesn't take up a lot of space when stored. One option I was looking at is the Blum Bench Horse. It's light enough that I…
-
- 1 reply
- 3.9k views
-
-
Been contemplating a new bench build for a while, but don't have space for a full size "Wood Whisperer Roubo" (I think about 6 and half feet long is my max). I am currently looking at vises, and pouring over schwarz's book on workbenches. I am thinking the Veritas Quick Release Tail Vise for the end, and a Veritas twin screw vise for the face. I am also looking at the bench crafted "chop" style hardware (with the X), as well as a quick release front vise from Veritas. Any opinions? Tail Vise http://www.leevalley.com/en/wood/page.aspx?p=65746&cat=1,41637,41659 Twin Screw Vise http://www.leevalley.com/en/wood/page.aspx?p=45114&cat=1,41637,45114 Q…
-
-
- 9 replies
- 4.8k views
-
-
Nothing fancy here. Just showing the tools I'm going to use as they come into the shop. I picked up my Frankensaw Saturday and started checking things and seeing how it will go together. A few things needed to be tightened and the motor bracket slot needs to be tweaked a little. The fence rail goes out to over 9 feet to the right of the blade. I will probably cut that off a little. They had a sheet metal catch pan screwed to the bottom of the saw. It looks like that's where they had the dust collector hooked up. More later.
-
-
- 58 replies
- 16.5k views
-
Who's Online (See full list)
Forum Statistics
- Total Topics 32.1k
- Total Posts 437.6k
Member Statistics
- 26,009 Total Members
- 3,644 Most Online
-
Joseph b Newest Member ·